key TOYOTA AVENSIS 2003 Service Workshop Manual

Within 40 sec.
ON
LOCK
ON±LOCK operation: 1 time
Add Mode
Rewrite Mode
ON±LOCK operation: 2 times
Confirmation Mode
ON±LOCK operation: 3 times
All Clear Mode
ON±LOCK operation: 5 times
Number of ON±LOCK operations of ignition switch:
Turn ignition switch from LOCK to ON and back to LOCK at approximately
1 second intervals according to the number of times shown below.
Mode Selection:
If the number of the ON±LOCK operations of the ignition switch
is 0, 4 or 6 or more, there will be no response (power door lock and
unlock operation) to inform which mode has been selected.
Remove key from ignition key cylinder.
8.
7.
Within 3 sec.
T1
T1: Approx. 1 sec.
Continued from previous page
Continued on next page
ON
LOCK T1 T1
ON
LOCK T1 T1
ON
LOCK T1 T1
±
THEFT DETERRENT & DOOR LOCK TRANSMITTER SUB±ASSY MODULE SET DOOR
CONTROL73±23
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

Continued from previous page
Press either LOCK or UNLOCK switch on transmitter once.
9.
Within 40 sec.
Proceed to flow chart to finish
registration.
Press the same switch again.
LOCK±UNLOCK Occurs Once Registration of recognition code has
been completed.
Response to registration completion:
T1: Approx. 1 sec.
LOCK±UNLOCK Occurs Twice
Registration of recognition code has failed.
10.
LOCK
UNLOCK
T1
LOCK
UNLOCK T1 T1
Within
40 sec.
If other transmitter is to be registered.
Within
3 sec.
Registration of recognition codes (add mode and rewrite mode) is compl\
eted.
Integration relay automatically performs power door LOCK±UNLOCK operation to show
whether registration has been completed correctly or not.
HINT:
4 recognition codes can be registered
at once.
HINT:
If LOCK±UNLOCK operation is performed twice, registration of recognition\
code has
failed. Perform registration procedures by beginning once again.
Within
3 sec.


Open a door.

Insert key into ignition key cylinder.
Perform either of the following.
±
THEFT DETERRENT & DOOR LOCK TRANSMITTER SUB±ASSY MODULE SET DOOR
CONTROL73±25
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

730EU±02
73±14
±
THEFT DETERRENT & DOOR LOCK WIRELESS DOOR LOCK CONTROL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
WIRELESS DOOR LOCK CONTROL SYSTEM
PRECAUTION
1. NOTICES WHEN CHECKING
(a) The wireless door lock remote control function operates only when the follo\
wing 3 conditions are met. (1) All the doors are closed.
(2) No key is inserted in the ignition key cylinder.
(3) The power door lock system operates normally.
HINT:
The door UNLOCK and luggage door (back door) UNLOCK functions operate \
even when a door is open.
(b) The wireless door lock remote control operational area differs depending on the situation. (1) The operational area differs depending on the operators and the ways the transmitter is held.
(2) In certain areas, the remote control function will only operate partiall\
y for the operational area
will be reduced due to the vehicle body shape and the influence of the surrounding environment.
(3) Since the transmitter uses faint electric waves, strong electric waves or noise in the frequency used may reduce the operational area or the remote control may not funct\
ion.
(4) When the battery weakens, the operational area is reduced or the remote control may not func-
tion.
HINT:
If the door control transmitter has been left in a place that is exposed t\
o the direct sunlight, such as on the
instrument panel, it may cause the battery to weaken or cause other such\
problems.
http://vnx.su

730EV±02
±
THEFT DETERRENT & DOOR LOCKWIRELESS DOOR LOCK CONTROL SYSTEM
73±15
AVENSIS REPAIR MANUAL (RM1018E)
ON±VEHICLE INSPECTION
1.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
HINT:

The switch described in this text is a switch for transmitting signals (LO\
CK switch, UNLOCK switch and
luggage door (back door) unlock switch) which is built in the door control t\
ransmitter.

All the functions listed below must be checked in comparison with the re\
mote control operational area.
(a)Put the vehicle under the conditions that allow the wireless control fun\
ction to be operated (See PRE-
CAUTION on page 73±14).
(b) Check the basic function. (1) Check whether the LED of the transmitter lights up 3 times when each switch i\
s pressed 3 times.
HINT:
If the LED does not light up when the switch has been pressed 3 times or more, it may have a dead bat\
tery.
(2) Check that all the doors including the luggage door (back door) lock when t\
he LOCK switch ispressed (However, this will not happen when any door is open).
(3) w/ Double locking system: Check that the double locking system is set when the LOCK switch is pressed within 5 seconds
after the above step (However, the double locking system is not applicable to the luggage door
(back door)).
CAUTION:
Never activate the double locking system when there are people in the vehicle, because all the doors
cannot be opened from inside the vehicle with the system on. If you lock\
the doors by accident, push
UNLOCK switch of the door control transmitter. (4) Check that all the doors including the luggage door (back door) unlock when\
the UNLOCK switchis pressed. Also, check that the double locking system is canceled at th\
e same time.
(5) Check that the luggage door (back door) unlocks when the luggage door (bac\
k door) unlock
switch is pressed.
HINT:
The UNLOCK switch and luggage door (back door) unlock switch can unlock t\
he doors even when any door
is open.
(c) Check the chattering prevention function. (1) Check that the corresponding operation occurs only once, and not repeated continuously whilethe switch is held down. However, when the switch is operated repeatedly at 1 second intervals,
check that the corresponding operation is carried out.
(d) Check the automatic locking function. (1) Check that all the doors including the luggage door (back door) lock automatically as long asnone of them have been opened or locked within approx. 30 seconds after they\
are unlocked
by pressing the switch.
(2) Check that the automatic locking function does not operate when any door incl\
uding the luggage
door (back door) has been opened or all of them have been locked within ap\
prox. 30 seconds
after they are unlocked by pressing the switch.
(e) Check the switch operation fail±safe function. (1) Check that the doors can not be locked by the switch while the key is in the \
ignition key cylinder.
However, this does not apply when the system is in the recognition code registra\
tion mode.
(f) Check the repeat function. (1) Check that all the doors attempt to automatically lock once again 1 second af\
ter the LOCK switchhas been pressed while the movement of the driver side door control knob, which is in the un-
locked state, is being restricted.
http://vnx.su

B59092
Wire Harness SideDoor Control Receiver
73±16
±
THEFT DETERRENT & DOOR LOCK WIRELESS DOOR LOCK CONTROL SYSTEM
AVENSIS REPAIR MANUAL (RM1018E)
(g) Check the hazard warning lamps flashing function (answer±back). (1) When the LOCK switch is pressed, check that the hazard warning lamps flash once, simulta-neously with the locking of all the doors.
(2) When the UNLOCK switch is pressed once, check that the hazard warning lamps \
flash twice si- multaneously with the unlocking of all the doors.
(3) When the luggage door (back door) unlock switch is pressed once, check tha\
t the hazard warn- ing lamps flash twice simultaneously with the unlocking of the luggage door\
(back door).
2. CHECK DOOR CONTROL RECEIVER
(a) Disconnect the receiver connector.
(b) Check the voltage and resistance between the terminalsof the wire harness side connector and the body ground.
Standard:
Tester ConnectionConditionSpecified Condition
5 (+B) ± Body groundConstant10 to 14 V
1 (GROUND) ± Body groundConstantBelow 1

If the result is not as specified, there may be a malfunction on the wire \
harness side.
(c) Reconnect the connector and check the voltage between the terminal and b\
ody ground.
Standard:
Tester ConnectionConditionSpecified Condition
2 (RDA) ± Body groundNo key in ignition key cylinder, all doors closed
and each transmitter switch OFF ONBelow 1 V Approx. 6 to 7 V Below 1 V
If the result is not as specified, the receiver may have a malfunction.
http://vnx.su

B67989
Front Door Outside Handle Frame Sub±assy LHw/ Key:
Front Door Outside Handle Cover LH
Front Door Handle
Assy Outside LH
Front Door Outside Handle Pad Rear
Front Door Outside
Handle Pad Front
Hole Plug
Front Door Lock Open Rod
Front Door w/ Motor Lock Assy LH
Door Lock Wire Harness Packing
5.0 (51, 44 in.´lbf)
Front Door Belt Moulding LH
Front Door Hinge
Assy Upper LH
Front Door Check Assy
30 (306, 22)

5.5 (56, 49 in.´lbf)
Front Door Hinge
Assy Lower LH26 (265, 19)
Front Door Weatherstrip LH
Cushion Rubber Front Door Lower Frame
Bracket Garnish LH
Outer Rear View Mirror Assy LH
Front Door Speaker No. 2
Front Door Service Hole Cover

: Specified torqueN´m (kgf´cm, ft´lbf)

Precoated Part Non±reusable part
 Clip
26 (265, 19)
Front Door Lower
Frame Seal


Butyl Tape

10 (102, 7)
Front Door Stiffener
Cushion No. 1
Side Trim
Spacer LH
Key Cylinder
w/o Key:
Front Door Outside
Handle Cover LHw/ SpeakerFront Door Lower Frame
Bracket Garnish LH
±
ENGINE HOOD/DOOR FRONT DOOR
75±5
AVENSIS REPAIR MANUAL (RM1018E)
http://vnx.su

B62422
B62423
12
B66968
B61434

B68932Hole Plug
±
ENGINE HOOD/DOOR FRONT DOOR
75±11
AVENSIS REPAIR MANUAL (RM1018E)
14. REMOVE FRONT DOOR GLASS SUB±ASSY LH
HINT:
Insert a shop rag inside the door panel to prevent the glass from
being scratched.
(a) Move the door glass until the bolts appear in the service
holes.
(b) Remove the 2 bolts holding the door glass to the window
regulator.
(c) Remove the door glass in the direction indicated by the arrows in the illustration.
NOTICE:

Do not damage the glass.

When the bolts are removed, the glass may fall and
become deformed.
(d) Remove the glass run.
15. REMOVE FRONT DOOR WINDOW REGULATOR SUB±ASSY LH
(a) Disconnect the window regulator connector.
(b) Remove the 6 bolts and window regulator.
NOTICE:
When the bolts are removed, the window regulator may fall
and become deformed.
HINT:
Remove the window regulator through the service hole.
16. REMOVE FRONT DOOR FRAME SUB±ASSY REAR LOWER LH
(a) Remove the bolt and frame.
HINT:
Remove the frame through the service hole.
17. REMOVE FRONT DOOR OUTSIDE HANDLE COVER
(a) Remove the hole plug.
(b) Using a torx socket wrench (T30), loosen the screw and remove the cover with the door lock key cylinder installed.
http://vnx.su

B65961
Rod
B66894
Adhesive
Adhesive

B68932Hole Plug
B62425
B66972
75±14
±
ENGINE HOOD/DOOR FRONT DOOR
AVENSIS REPAIR MANUAL (RM1018E)
(c) Insert the control rod into the door lock, and then set it to the door panel.
NOTICE:
Make sure that the handle link is securely engaged with the
lock.
(d) Apply adhesive to the threads of the 3 screws. Adhesive:
Part No. 08833±00070, THREE BOND 1324 or equiva-
lent
(e) Using a torx socket wrench (T30), install the door lock with the 3 screws.
Torque: 5.0 N
m (51 kgf
cm, 44 in.
lbf)
(f) Connect the door lock connector.
27. INSTALL FRONT DOOR OUTSIDE HANDLE COVER
(a) Using a torx socket wrench (T30), install the cover with the door lock key cylinder installed with the screw.
Torque: 7.0 N
m (71 kgf
cm, 62 in.
lbf)
(b) Install the hole plug.
28. INSTALL FRONT DOOR FRAME SUB±ASSY REAR
LOWER LH
(a) Install the frame with the bolt. Torque: 5.5 N
m (56 kgf
cm, 49 in.
lbf)
29. I N S TA L L F R O N T D O O R W I N D O W R E G U L ATO R SUB±ASSY LH
(a) Apply MP grease to the sliding and rotating areas of the
window regulator.
NOTICE:
Do not apply grease to the spring of the window regulator.
http://vnx.su

AVENSIS (EWD526E)9
B
The
”Current Flow Chart” section, describes which parts each power source (fuses, fusible links\
, and circuit breakers)
transmits current to. In the Power Source circuit diagram, the condition\
s when battery power is supplied to each system
are explained. Since all System Circuit diagrams start from the power so\
urce, the power source system must be fully
understood.
ACC
S 2 6
6
5 2
22
Battery 30A AM2
Starter Short Pin
100A ALT
Fusible Link Block
60A ABS10A ECU–B
7.5A DOME
15A EFI
10A HAZARD
20A RADIO NO.1
10A HORN
20A
10A Fuse
Page
214
230
11 2
122 194
187
180
166
210
ABS
Cigarette Lighter
Combination Meter
Key Reminder and Seat Belt Warning
Light Auto Turn Off
Theft Deterrent and Door Lock ControlABS and Traction Control
Cruise Control
Electronically Controlled Transmission
Multiplex Communication System
STOP System
DOME Headlight
Interior Light
3 EA2 1 EA1E 6
E 7
E 7
2
2
2
2 2
2 2
2
INJECTION Relay
STARTER Relay
B
B
B
B–O
1
1 2
23
4
3
4
W–B W–B
B–W
B–W
E 7
E 7 B
B W
1.25B FL MAIN
50A MAIN
7.5A AM2
15A HAZ–RADIO
2
2 2
2
2W
W EB1
EB1
7
6
W–R I 2 I 2 I 2
WW
W
W W
1 1
1 140A DOOR LOCK CB
7.5A DOME
1
W–L
R
1
1
2
43 1
11
1
1 1 1
G
G
W–R
15A TAIL
20A DEFOG
B–Y
84
32Ignition SW I 8
B–Y 1 1P–L
Battery
15A RAD CIG2
TAIL
Relay
Power Source
J POWER SOURCE (Current Flow Chart)
Engine Room R/B (See Page 20)
2
W W
B
B
B
B
B
W–RWW
W
G–W AM2
AM1
IG2
IG1 W
W
The chart below shows the route by which current flows from the battery \
to each electrical source
(Fusible Link, Circuit Breaker, Fuse, etc.) and other parts.
∗ The system shown here is an EXAMPLE ONLY. It is different to the actual circuit shown in the SYSTEM CIRCUITS SECTION.
http://vnx.su

A 1
L PART NUMBER OF CONNECTORS
A/C Ambient Temp. Sensor
Code
90980–11070Part Number
D 4 Diode (Courtesy)
Code
90980–11608
A 2 A/C Condenser Fan Motor 90980–11237 D 5 Diode (Interior Light) 90980–10962
A 3 A/C Condenser Fan Relay 90980–10940 D 6 Diode (Moon Roof) 90980–11608
A 4 A/C Condenser Fan Resistor 90980–10928
90980–11271D 7 Door Lock Control Relay
90980–10848
A 5 A/C Magnetic Clutch
90980–11413D 8 Door Lock Control SW LH
90980–11148
A 6 A/T Oil Temp. Sensor
90980–11151D 9 Door Lock Control SW RH
A 7 ABS Actuator 90980–11009Door Courtesy SW LH
90980–11097
A 8 ABS Actuator
90980–10941Door Courtesy SW RH
A 9 ABS Speed Sensor Front LH
90980–11002Door Courtesy SW Front LH
ABS Speed Sensor Front RH
90980–11856Door Courtesy SW Front RH
90980–11156
Airbag Sensor Front LH Door Courtesy SW Rear LH
Airbag Sensor Front RH Door Courtesy SW Rear RH
A10
A11
A12
A13 Airbag Squib
90980–11194Door Key Lock and Unlock SW LH
90980–11170
90980–11070 D10
D11
D12
D13
D14
D15
D16
D17 Door Key Lock and Unlock SW RH Part Number
Part Name
Part Name
[A]
[B] [C]
AVENSIS (EWD526E) 11
B
[A]
: Part Code
[B] : Part Name
[C] : Part Number
Toyota Part Number are indicated.
Not all of the above part numbers of the connector are established for t\
he supply.
http://vnx.su