oil level TOYOTA AVENSIS 2005 Service Owner's Manual

A79295
N´m (kgf´cm, ft´lbf)
: Specified torque

Non±reusable part
5.0 (50, 43 in.
lbf)

O±ring

Gasket
Gasket
Gasket
Gasket

O±ring
15 (153, 11)
20 (204, 15)
9.0 (92, 80 in.
lbf)
9.0 (92, 80 in.
lbf)
Fuel Delivery Pipe
w/ Injector
Oil Control Valve
Knock Control SensorSpacer
Water By±pass Pipe No. 1
Oil Level Gauge
Sub±assy
Oil Level Gauge Guide
Water Inlet
9.0 (92, 79 in.
lbf)Engine Oil Pressure Switch Assy
Water Temperature Sensor
Thermostat
9.0 (92, 80 in.
lbf)
19 (194, 14)
19 (194, 14)
20 (204, 15)
14±120
± ENGINE MECHANICALPARTIAL ENGINE ASSY (1AZ±FE)
AVENSIS REPAIR MANUAL (RM1018E)

A65078
A64058
A79363
A64026
± ENGINE MECHANICALCYLINDER HEAD GASKET (1ZZ±FE/3ZZ±FE)
14±83
AVENSIS REPAIR MANUAL (RM1018E)
22. DISCONNECT VENTILATION HOSE
(a) Disconnect the ventilation hose from the cylinder head
cover.
23. DISCONNECT VENTILATION HOSE NO.2
(a) Disconnect the ventilation hose from the cylinder head
cover.
24. REMOVE INTAKE MANIFOLD
(a) Disconnect the 2 water hoses from the throttle body.
(b) Disconnect the ventilation hose and ventilation hose No.
2 from the cylinder head cover.
(c) Disconnect the vacuum hose from the water by±pass
pipe No. 1.
(d) Remove the 4 bolts, 2 nuts and 2 wire brackets.
(e) Remove the intake manifold and the throttle body assem-
bly.
(f) Remove the gasket from the intake manifold and the
throttle body assembly.
25. REMOVE OIL LEVEL GAGE SUB±ASSY
(a) Remove the oil level gage from the oil level gage guide.
26. REMOVE OIL LEVEL GAGE GUIDE
(a) Disconnect the crankshaft position sensor cramp.
(b) Remove the bolt and the oil level gage guide.
27. SEPARATE WATER BY±PASS PIPE NO.1
(a) Remove the 2 bolts which are used to secure the water
by±pass pipe.

A76720
AAB
A76721
B06777
A64026
A79363
14±94
±
ENGINE MECHANICAL CYLINDER HEAD GASKET(1ZZ±FE/3ZZ±FE)
AVENSIS REPAIR MANUAL (RM1018E)
68.INSTALL MANIFOLD STAY
(a)Install the manifold stay with the 3 bolts. Torque:
37 N
m (377 kgf
cm, 27 ft
lbf) for Bolt A
49 N
m (500 kgf
cm, 36 ft
lbf) for Bolt B
69.INSTALL MANIFOLD STAY NO.2
(a)Install the manifold stay with the 3 bolts. Torque: 49 N
m (500 kgf
cm, 36 ft
lbf)
70.INSTALL EXHAUST PIPE ASSY FRONT (See page 15±2)
71. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSY
(a) Apply a light coat of engine oil on a new O±ring, and install it to the camshaft timing oil control valve.
(b) Install the camshaft timing oil control valve with the bolt.
Torque: 9.0 N
m (92 kgf
cm, 80 in.
lbf)
72. INSTALL WATER BY±PASS PIPE NO.1
(a) Install a new gasket and water by±pass pipe with the 2 nuts and 2 bolts.
Torque: 9.0 N
m (92 kgf
cm, 80 in.
lbf)
73. INSTALL OIL LEVEL GAGE GUIDE
(a) Apply a light coat of engine oil on a new O±ring, and install it to the oil level gage guide.
(b) Install the oil level gage guide with the bolt.
Torque: 13 N
m (133 kgf
cm, 10 ft
lbf)
74. INSTALL INTAKE MANIFOLD
(a) Install a new gasket to the intake manifold.
(b) Install the intake manifold and the throttle body assembly with the 2 brackets, 4 bolts and 2 nuts.
Torque: 30 N
m (306 kgf
cm, 22 ft
lbf)
(c) Connect the 2 vacuum hoses to the intake manifold.
(d) Connect the 2 water hoses to the throttle body.

A76712
Camshaft
Camshaft No. 2
Plate Washer Camshaft Bearing Cap No. 1
Camshaft Bearing Cap No. 3
Cylinder Head Sub±assy Camshaft Timing
Oil Control Valve Assy
 Cylinder Head Gasket
Manifold Stay No. 1 Intake Manifold
Clamp Bracket
Oil Level Gage Guide
 O±ring Oil Level Gage
Sub±assy

Non±reusable part
N´m (kgf´cm, ft´lbf): Specified torque
13 (133, 10)
23 (235, 17)
30 (306, 22)
9.0 (92, 80 in.
lbf)
1st 49 (500, 36)
2nd Turn 90

See page 14±81
49 (500, 36)

Gasket
Manifold Stay No. 2
37 (377, 27)
 O±ring
9.0 (92, 80 in.
lbf)
13 (133, 10)
49 (500, 36)
14±80
±
ENGINE MECHANICAL CYLINDER HEAD GASKET (1ZZ±FE/3ZZ±FE)
AVENSIS REPAIR MANUAL (RM1018E)

A77328
N´m (kgf´cm, ft´lbf)
: Specified torque

Non±reusable part
30 (301, 22)

O±ring
Bearing Cap No. 1
Bearing Cap No. 2
9.0 (92, 80 in.
lbf)
Bearing Cap No. 3
Camshaft
No. 2 Camshaft
Camshaft Bearing No. 2
Camshaft Timing
Oil Control Valve Assy
Cylinder Head

Cylinder Head Gasket
9.0 (92, 80 in.
lbf)
Oil Level Gauge
Sub±assy
9.0 (92, 80 in.
lbf)

O±ring
Oil Level Gauge
Guide
1st: 79 (800, 58)
2nd: Turn 90

30 (301, 22)
9.0 (92, 79 in.
lbf)
± ENGINE MECHANICALCYLINDER HEAD GASKET (1AZ±FE)
14±159
AVENSIS REPAIR MANUAL (RM1018E)

A32676
A77350
A52497
±
ENGINE MECHANICAL PARTIAL ENGINE ASSY(1AZ±FSE)
14±211
AVENSIS REPAIR MANUAL (RM1018E)
80.REMOVE INTAKE AIR CONTROL VALVE ASSY
(a)Remove the intake air control valve and a gasket.
81.REMOVE SURGE TANK STAY NO.1
(a)Remove the 3 bolts and the surge tank stay.
82.REMOVE INTAKE MANIFOLD INSULATOR NO.2
83.REMOVE NOZZLE HOLDER CLAMP
84.REMOVE FUEL DELIVERY PIPE SUB±ASSY (See page 11±42)
85.REMOVE FUEL INJECTOR ASSY (See page 11±42)
86. REMOVE V±RIBBED BELT TENSIONER ASSY
(a) Remove the bolt and nut, and then detach the V±ribbedbelt tensioner.
87. REMOVE IGNITION COIL ASSY
(a) Remove the 4 bolts and the ignition coils.
88. REMOVE EXHAUST MANIFOLD HEAT INSULATOR NO.1
(a) Remove the 3 bolts and the exhaust manifold heat insulator. 89. REMOVE EXHAUST MANIFOLD CONVERTERSUB±ASSY
(a) Remove the 2 bolts and 2 nuts, then detach the No. 1 and No. 2 exhaust manifold stay.
(b) Remove the 5 nuts, the exhaust manifold converter and gasket.
90. REMOVE OIL LEVEL GAGE SUB±ASSY
91. REMOVE OIL LEVEL GAGE GUIDE
92. REMOVE WATER INLET
(a) Remove the 2 nuts and the water inlet.
93. REMOVE THERMOSTAT

A78645
Oil Pressure Switch
14±212
±
ENGINE MECHANICAL PARTIAL ENGINE ASSY(1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)
94.REMOVE WATER BY±PASS PIPE NO.1
(a)Remove the 2 bolts and 2 nuts.
(b)Remove the water by±pass pipe No. 1 and a gasket.
95.REMOVE KNOCK SENSOR
(a)Remove the nut and the knock sensor. 96.REMOVE ENGINE OIL PRESSURE SWITCH ASSY
(a)Using SST, remove the engine oil pressure switch.SST09268±46021
97.REMOVE E.F.I. ENGINE COOLANT TEMPERATURE SENSOR
(a)Using a SST, remove the coolant temperature sensor SST09817±33190
98.REPLACE PARTIAL ENGINE ASSY
99.INSTALL E.F.I. ENGINE COOLANT TEMPERATURE SENSOR
(a)Install a new gasket to the engine coolant temperature sensor.
(b)Using SST, install the engine coolant temperature sensor. SST09817±33190
Torque: 20 N
m (208 kgf
cm,15 ft
lbf)
100.INSTALL ENGINE OIL PRESSURE SWITCH ASSY
(a)Clean the threads of the oil pressure switch, apply adhesive there.
Adhesive: Part No. 08833 ± 00080 THREE BOND 1344 or equivalent.
(b)Install the oil pressure switch. Torque: 15 N
m (153 kgf
cm,11 ft
lbf)
SST09268±46021
101.INSTALL KNOCK SENSOR Torque: 20 N
m (208 kgf
cm,15 ft
lbf)
102.INSTALL WATER BY±PASS PIPE NO.1
(a)Install the water by±pass pipe No. 1 and a new gasket.
(b)Install the 2 bolts and 2 nuts. Torque: 9.0 N
m (92 kgf
cm,80 in.
lbf)
103.INSTALL THERMOSTAT (See page 16±35)
104. INSTALL WATER INLET Torque: 9.0 N
m (92 kgf
cm, 80 in.
lbf)
105. INSTALL OIL LEVEL GAGE GUIDE
(a) Apply a light coat of engine oil to the O±ring, install it to the oil\
level gauge guide.
(b) Install the oil level gauge and guide with the bolt. Torque: 9.0 N
m (92 kgf
cm, 80 in.
lbf)

A77499
N´m (kgf´cm, ft´lbf)
: Specified torque

Non±reusable part
GasketWater By±pass
Pipe No. 1
Gasket
Thermostat
9.0 (90, 80 in.
lbf)
Water Inlet
37 (378, 27)Oil Level Gauge
Guide

O±ring
Manifold Stay No. 2
Exhaust Manifold
Converter Sub±assy Manifold Stay No. 1
9.0 (90, 80 in.
lbf)
9.0 (90, 80 in.
lbf)

Gasket
9.0 (90, 80 in.
lbf)
12 (122, 9.0)12 (122, 9.0)
12 (122, 9.0)
44 (449, 32)
44 (449, 32)
Oil Level Gauge Sub±assy
14±202
± ENGINE MECHANICALPARTIAL ENGINE ASSY (1AZ±FSE)
AVENSIS REPAIR MANUAL (RM1018E)

A79424
N´m (kgf´cm, ft´lbf)
: Specified torque

Non±reusable part
8.8 (90, 65 in.
lbf)
8.8 (90, 6.5 in.
lbf)
8.4 (86, 74 in.
lbf)
21 (209, 15)
8.8 (90, 78 in.
lbf)
34 (347, 25)
18 (184, 13)21 (210, 15)
21 (210, 15)
42 (428, 31)
37 (377, 27)
59 (600, 43)
21 (214, 15)
45 (454, 33)

O±ring

O±ring

Gasket

O±ring

O±ring
Vacuum Pump Oil Pipe
Union Bolt
Oil Cooler AssyFuel Filter To Injection Pump
Fuel Pipe
Rear End Plate
Crankshaft Position
Sensor
Thermostat
Water Inlet
Oil Level Gage Guide Oil Filter Bracket Sub±assy
Injection or Supply Pump Assy Compressor Mounting
Bracket No. 1Generator Bracket No. 1 V±ribbed Belt
Tensioner
AssyGenerator Assy
Oil Cooler Pipe

Gasket
Turbo Oil Outlet Pipe No. 2
31 (320, 23)

Gasket
33 (331, 24)
8.8 (90, 78 in.
lbf)
47 (475, 34)
± ENGINE MECHANICALPARTIAL ENGINE ASSY (1CD±FTV)
14±285
AVENSIS REPAIR MANUAL (RM1018E)

A77328
N´m (kgf´cm, ft´lbf)
: Specified torque

Non±reusable part
30 (301, 22)

O±ring
Bearing Cap No. 1
Bearing Cap No. 2
9.0 (92, 80 in.
lbf)
Bearing Cap No. 3
Camshaft
No. 2 Camshaft
Camshaft Bearing No. 2
Camshaft Timing
Oil Control Valve Assy
Cylinder Head

Cylinder Head Gasket
9.0 (92, 80 in.
lbf)
Oil Level Gauge
Sub±assy
9.0 (92, 80 in.
lbf)

O±ring
Oil Level Gauge
Guide
1st: 79 (800, 58)
2nd: Turn 90

30 (301, 22)
9.0 (92, 79 in.
lbf)
± ENGINE MECHANICALCYLINDER HEAD GASKET (1AZ±FSE)
14±253
AVENSIS REPAIR MANUAL (RM1018E)