fuel filter TOYOTA AVENSIS 2005 Service Manual PDF

100LW−01
A84695
Mass Air Flow
Meter Connector
N·m (kgf·cm, ft·lbf) : Specified torqueEngine Cover Sub−assy
No. 1
9.0 (92, 80 in.
lbf)
VSV
Connector Fuel Vapor Feed
Hose
Clip
Engine Room Cover Side
Radiator Support Opening Cover
Clip
Retainer
x2
x4
1.5 (15, 13 in.
lbf)
Air Cleaner Filter
Element Sub−assy x2
Air Cleaner Cap
Sub−assy 10−6
− ENGINE CONTROL SYSTEMTHROTTLE BODY ASSY (2AZ−FSE)
AVENSIS Supplement (RM1045E)
THROTTLE BODY ASSY (2AZ−FSE)
COMPONENTS

A85746
Union to Connector Tube Hose
Fuel Filter Assy Vacuum Reservoir Sub−assy
43 (440, 32)
43 (440, 32)
zGasket
zGasketCompression Spring
Floor Panel Brace Front Exhaust Pipe Assy Front
Compression Spring
N·m (kgf·cm, ft·lbf)
: Specified torque
zNon−reusable partzGasket
7.5 (76, 66 in.
lbf)
Exhaust Pipe Assy
30 (302, 22)
7.5 (76, 66 in.
lbf)
Heater Bracket
Heater Pump Assy25 (255, 18)
25 (255, 18)
7.5 (76, 66 in.
lbf)
18 (178, 13)
7.5 (76, 66 in.
lbf)
w/ Cold Area:
w/ Cold Area:
w/ Cold Area:
8.3 (85, 73 in.
lbf)
Air Tube No. 1
x2
43 (440, 32)
6.0 (61, 53 in.
lbf)
13−10− INTAKETURBOCHARGER SUB−ASSY (1CD−FTV)(From
September, 2003)
AVENSIS Supplement (RM1045E)

A85742
5.0 (51, 44 in.
lbf)
* 36 (372, 27)
40 (408, 30)
* 31 (316, 23)
34 (347, 25)
* 31 (316, 23)
34 (347, 25)
Injection Pipe Clamp No. 2
Injection Pipe Sub−assy
zFuel Inlet Pipe Sub−assy
64 (653, 47)
Injection Pump
Drive Pulley
zO−ring Oil Level Gage Guide
: Specified torqueN·m (kgf·cm, ft·lbf)
* Use SST
18 (184, 13)
Oil Level Gage Sub−assy Injection or
Supply Pump Assy
21 (209, 15)
21 (209, 15)
Water Inlet
8.8 (90, 78 in.
lbf)
zGasket
5.0 (51, 44 in.
lbf)
Intake Manifold Insulator No. 1
Injection Pump to Fuel Filter
Fuel Hose or Pipe
Injection Pump to Fuel Pipe
Fuel Hose
Fuel Pipe No. 3
zGasket
27 (275, 20)
5.0 (51, 44 in.
lbf)
x3
zNon−reusable part
5.0 (51, 44 in.
lbf)
* 22 (223, 16)
24 (240, 17)
* 31 (316, 23)
34 (347, 25)
− FUELINJECTION OR SUPPLY PUMP
ASSY (1CD−FTV)(From September, 2003)11−57
AVENSIS Supplement (RM1045E)

1111 D−01
A93661
(a)
(a)
(b)(b)
(a)
(a)
A85630
11−46
− FUELINJECTOR ASSY (1CD−FTV)(From September, 2003)
AVENSIS Supplement (RM1045E)
REPLACEMENT
NOTICE:
If an incorrect injector compensation code was registered with the ECM, it may rattle the engine as-
sembly or the engine idling may become rough. In addition, it may become a cause of engine failure
or shorten the life of the engine.
HINT:
SIn order to optimize the injector’s fuel injection characteristic, the ECM compensates the injection dura-
tion by each cylinder. The ECM stores and uses compensating data in the form of a 30−digit−alphanu-
meric value that is imprinted on the head portion of each injector as the injector compensation code.
SIf you installed a new injector, its own injector compensation code is needed to register with the ECM.
Also, if you replaced the ECM, the compensation codes of all the injectors are needed to register be-
cause the new ECM does not have the codes until they are registered.
SOnce the ECM is replaced, DTC P1601 will be present when turning the ignition switch to ON. This
is to inform you that the injector compensation codes are required to register with the ECM. In order
to clear the DTC, register the compensation codes first, then turn the ignition switch to OFF and wait
for 30 seconds or longer.
1. REMOVE VACUUM RESERVOIR SUB−ASSY
(a) Disconnect the 2 vacuum hoses and connector.
(b) Remove the 2 bolts and vacuum reservoir.
2. REMOVE RADIATOR SUPPORT OPENING COVER
3. REMOVE ENGINE COVER SUB−ASSY NO.1
(a) Remove the 5 nuts and engine cover.
4. REMOVE AIR CLEANER ASSY
(a) Disconnect the connector.
(b) Remove the air cleaner cap together with the air cleaner hose.
(c) Remove the air cleaner filter element.
(d) Remove the 3 bolts and air cleaner case.
5. REMOVE AIR TUBE NO.1
(a) Remove the 3 bolts and nut, then separate the air tube
No. 1.
(b) Loosen the hose clamp bolts.
6. REMOVE FUEL PIPE NO.3
(a) Remove the fuel pipe insulator.

1111 5−01
A84695
Mass Air Flow
Meter Connector
N·m (kgf·cm, ft·lbf) : Specified torqueEngine Cover Sub−assy
No. 1
9.0 (92, 80 in.
lbf)
VSV
Connector Fuel Vapor Feed
Hose
Clip
Engine Room Cover Side
Radiator Support Opening Cover
Clip
Retainer
x2
x4
1.5 (15, 13 in.
lbf)
Air Cleaner Filter
Element Sub−assy x2
Air Cleaner Cap
Sub−assy
− FUELFUEL PUMP ASSY (2AZ−FSE)
11−21
AVENSIS Supplement (RM1045E)
FUEL PUMP ASSY (2AZ−FSE)
COMPONENTS

No.1 Fuel Pipe
Fuel Tube Connector
SST
(Clip)
SST (T joint)SST
SST
(Hose)
B12975
− FUELFUEL SYSTEM (2AZ−FSE)
11−5
AVENSIS Supplement (RM1045E)
(g) Install SST (pressure gauge) and the fuel tube connector
using SST as shown in the illustration.
SST 09268−41047(95336−08070),09268−45014
(09268−41250, 09268−41200, 09268−41220)
(h) Wipe up any gasoline.
(i) Reconnect the negative (−) battery cable.
(j) Connect the hand−held tester to the DLC3.
(k) Measure the fuel pressure.
Fuel pressure:
196 to 588 kPa (2 to 6 kgf/cm
2, 28 to 85 psi)
If pressure is high, replace the fuel pressure regulator.
If pressure is low, check the fuel hose connections, fuel pump,
fuel filter and fuel pressure regulator.
(l) Disconnect the hand−held tester from the DLC3.
(m) Start the engine.
(n) Measure the fuel pressure at idle.
Fuel pressure:
196 to 588 kPa (2 to 6 kgf/cm
2, 28 to 85 psi)
(o) Stop the engine.
(p) Check that the fuel pressure remains as specified for 5
minutes after the engine has stopped.
Fuel pressure:147 kPa (1.5 kgf/cm
2, 21 psi) or more
If pressure is not as specified, check the fuel pump, pressure
regulator and/or fuel injectors.
(q) After checking the fuel pressure, disconnect the negative
(−) battery cable and carefully remove SST and the fuel
tube connector to prevent gasoline splash.
(r) Reconnect the No. 1 fuel pipe (fuel tube connector).
CAUTION:
After taking the precautions, connect the fuel tube con-
necter (quick type).
2. CHECK FUEL PUMP OPERATION AND CHECK FOR
FUEL LEAKS
(a) When using the hand−held tester.
(1) Connect the hand−held tester to the DLC3.
(2) Turn the ignition switch ON and the hand−held tes-
ter main switch ON.
NOTICE:
Do not start the engine.
(3) Select the ACTIVE TEST mode on the hand−held
tester.
(4) Perform the active test. Check that the fuel pump
operates and check for fuel leaks.

141NM−01
14 −166−
ENGINE MECHANICAL CYLINDER HEAD GASKET (1CD −FTV)(From
September, 2003)
AVENSIS Supplement (RM1045E)
REPLACEMENT
1. REMOVE FRONT WHEEL RH
2. REMOVE ENGINE UNDER COVER LH
3. REMOVE ENGINE UNDER COVER SUB −ASSY NO.1
4. REMOVE ENGINE UNDER COVER RH
5. REMOVE RADIATOR SUPPORT OPENING COVER
6. REMOVE ENGINE ROOM COVER SIDE
7. DRAIN ENGINE COOLANT (See page 16 −19)
8. DRAIN ENGINE OIL (See Pub. No. RM1018E on page 17 −30)
9. REMOVE ENGINE COVER SUB −ASSY NO.1 (See page 14 −90)
10. REMOVE VACUUM RESERVOIR SUB −ASSY (See page 14 −108)
11. REMOVE AIR CLEANER ASSY (See page 14 −108)
12. REMOVE BATTERY
13. REMOVE AIR TUBE NO.2 (See page 14 −108)
14. REMOVE AIR TUBE NO.1 (See page 14 −108)
15. REMOVE INJECTOR DRIVER (See page 14 −108)
16. REMOVE V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT NO.1
(See Pub. No. RM1018E on page 14 −269)
17. REMOVE GENERATOR V BELT (See Pub. No. RM1018E on page 14 −269)
18. SEPARATE POWER STEERING IDLE PULLEY BRACKET (See page 14 −138)
19. DISCONNECT ENGINE WIRE (See page 14 −138)
20. DISCONNECT VACUUM HOSE (See page 14 −108)
21. REMOVE DIFFERENTIAL PRESSURE SENSOR ASSY(See page 14 −108)
22. REMOVE ENGINE MOUNTING INSULATOR SUB −ASSY RH (See page 14 −138)
23. REMOVE CRANKSHAFT PULLEY (See page 14 −138)
SST 09213 −54015 (09213 −70020), 09330 −00021, 09950 −50013 (09951 −05010, 09952 −05010,
09953 −05020, 09954 −05031)
24. REMOVE IDLER PULLEY SUB −ASSY (See page 14 −138)
25. REMOVE TIMING BELT NO.2 COVER (See page 14 −138)
26. REMOVE TIMING BELT NO.1 COVER (See page 14 −138)
27. REMOVE TIMING BELT GUIDE
28. REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET (See page 14 −138)
29. SET NO. 1 CYLINDER TO TDC/COMPRESSION (See page 14 −138)
30. REMOVE TIMING CHAIN COVER PLATE (See page 14 −138)
31. REMOVE TIMING BELT (See page 14 −138)
HINT:
If reusing the timing belt, draw an arrow on the timing belt which indicates the engine revolution direction
and put match marks on the pulleys and timing belt.
32. REMOVE FUEL FILTER ASSY (See Pub. No. RM1018E on page 11 −82)
33. REMOVE HEATER PUMP ASSY (W/ COLD AREA) (See page 13 −12)
34. REMOVE HEATER BRACKET (W/ COLD AREA) (See page 13 −12)
35. REMOVE FLOOR PANEL BRACE FRONT (See page 15 −6)
36. REMOVE EXHAUST PIPE ASSY FRONT (See page 15 −6)
37. REMOVE EXHAUST PIPE ASSY (W/ COLD AREA) (See page 13 −12)
38. DISCONNECT RADIATOR HOSE INLET
39. DISCONNECT HEATER INLET WATER HOSE
40. DISCONNECT HEATER OUTLET WATER HOSE
41. DISCONNECT FUEL PIPE TO FUEL TUBE FUEL HOSE
42. DISCONNECT OIL COOLER HOSE

A87960
Fulcrum Length
30 cm (11.81 in.)
SST
−
ENGINE MECHANICAL CYLINDER HEAD GASKET (1CD −FTV)(From
September, 2003)14 −175
AVENSIS Supplement (RM1045E)
(b) Using SST, tighten the nut of the fuel inlet pipe on the
common rail side.
SST 09023 −12700
Torque:
31 N
m (316 kgf
cm, 23 ft
lbf) with SST
34 N
m (347 kgf
cm, 25 ft
lbf) without SST
HINT:
S Use a torque wrench with the fulcrum length of 30 cm
(11.81 in.).
S After the inlet pipe is reassembled, check that the used
pipe has no deflection and is installed properly. If it has
deflection or could not be installed properly, replace the
used pipe with a new pipe.
(c) Using SST, tighten the nut of the fuel inlet pipe on the pump side.
SST 09023 −12700
Torque:
31 N
m (316 kgf
cm, 23 ft
lbf) with SST
34 N
m (347 kgf
cm, 25 ft
lbf) without SST
HINT:
S Use a torque wrench with the fulcrum length of 30 cm
(11.81 in.).
S After the inlet pipe is reassembled, check that the used
pipe has no deflection and is installed properly. If it has
deflection or could not be installed properly, replace the
used pipe with a new pipe.
103. INSTALL TURBOCHARGER SUB −ASSY (See page 13 −12)
104. INSTALL TURBO OIL INLET PIPE SUB −ASSY (See page 13 −12)
105. INSTALL TURBOCHARGER STAY (See page 13 −12)
106. INSTALL MANIFOLD CONVERTER SUB −ASSY (See page 13 −12)
107. INSTALL MANIFOLD STAY NO.2 (See page 13 −12)
108. INSTALL VACUUM TRANSMITTING PIPE SUB −ASSY NO.2 (See page 14 −108)
SST 09023 −38200
109. INSTALL VACUUM TRANSMITTING PIPE SUB −ASSY NO.1 (See page 14 −108)
SST 09023 −38200
110. INSTALL EXHAUST GAS TEMPERATURE SENSOR (See page 14 −108)
SST 09023 −38400
111. INSTALL GENERATOR ASSY (See Pub. No. RM1018E on page 19 −29)
112. INSTALL EGR PIPE INSULATOR (See page 13 −12)
113. INSTALL EXHAUST MANIFOLD HEAT INSULATOR NO.2 (See page 13 −12)
114. INSTALL TURBO INSULATOR NO.1 (See page 13 −12)
115. INSTALL TURBO INSULATOR NO.2 (See page 13 −12)
116. INSTALL EXHAUST PIPE ASSY (W/ COLD AREA) (See page 13 −12)
117. INSTALL EXHAUST PIPE ASSY FRONT (See page 15 −6)
118. INSTALL FLOOR PANEL BRACE FRONT (See page 15 −6)
119. INSTALL HEATER BRACKET (W/ COLD AREA) (See page 13 −12)
120. INSTALL HEATER PUMP ASSY (W/ COLD AREA) (See page 13 −12)
121. INSTALL FUEL FILTER ASSY (See Pub. No. RM1018E on page 11 −82)

141NG−01
A84393
(a)
(a)
(b)(b)
(a)
A84286
14 −108−
ENGINE MECHANICAL PARTIAL ENGINE ASSY (1CD −FTV)(From September,
2003)
AVENSIS Supplement (RM1045E)
REPLACEMENT
1. REMOVE FRONT WHEELS
2. REMOVE ENGINE UNDER COVER LH
3. REMOVE ENGINE UNDER COVER SUB −ASSY NO.1
4. REMOVE ENGINE UNDER COVER RH
5. REMOVE RADIATOR SUPPORT OPENING COVER
6. REMOVE ENGINE ROOM COVER SIDE
7. DRAIN ENGINE COOLANT (See page 16 −19)
8. DRAIN ENGINE OIL (See Pub No. RM1018E on page 17 −30)
9. DRAIN MANUAL TRANSAXLE OIL
Torque: 49 N
m (500 kgf
cm, 36 ft
lbf)
10. REMOVE ENGINE COVER SUB −ASSY NO.1
(a) Remove the 5 nuts, then remove the engine cover.
11. REMOVE BATTERY
12. REMOVE AIR CLEANER ASSY
(a) Disconnect the mass air flow meter connector.
(b) Remove the air cleaner cap together with the air cleaner hose.
(c) Remove the air cleaner filter element.
(d) Remove the 3 bolts and air cleaner case.
13. REMOVE VACUUM RESERVOIR SUB −ASSY
(a) Disconnect the 2 vacuum hoses and connector.
(b) Remove the 2 bolts and vacuum reservoir.
14. REMOVE FUEL FILTER ASSY (See Pub. No. RM1018E on page 11 −82)
15. REMOVE RADIATOR HOSE INLET
16. REMOVE RADIATOR HOSE OUTLET
17. DISCONNECT WATER BY−PASS HOSE NO.2

A85929
(g)
(f)
(g)
A84394
A84395
A84396
(a)
(b)
A93840
Air Hose No. 2
To
Turbocharger (b)
(b)(c)
(c)
(c) 14−11 0
− ENGINE MECHANICALPARTIAL ENGINE ASSY (1CD−FTV)(From September,
2003)
AVENSIS Supplement (RM1045E)
(f) Remove the bolt and engine room relay block No. 3.
(g) Disconnect the 2 connectors.
(h) Disconnect the wire harness from the fuel filter support.
(i) Disconnect the 2 exhaust gas temperature sensor con-
nectors.
27. DISCONNECT VACUUM HOSE
(a) Disconnect the 2 vacuum hoses.
28. REMOVE DIFFERENTIAL PRESSURE SENSOR ASSY
(a) Disconnect the connector.
(b) Remove the bolt and differential pressure sensor.
29. REMOVE AIR TUBE NO.1
(a) Disconnect the vacuum hoses and connectors.
(b) Loosen the 2 hose clamps.
(c) Remove the 2 bolts and nut, then detach the air tube No.
1.