tow bar TOYOTA AVENSIS 2005 Service Repair Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2005, Model line: AVENSIS, Model: TOYOTA AVENSIS 2005Pages: 5135, PDF Size: 95.28 MB
Page 2546 of 5135
C86268
SST
C67417
Matchmarks
30±16
± DRIVE SHAFT / PROPELLER SHAFTFRONT DRIVE SHAFT
AVENSIS REPAIR MANUAL (RM1018E)
(5) Using SST, adjust the clearance of the damper
clamp.
SST 09240±00020
Clearance: 0.8 mm (0.031 in.) or less
NOTICE:
When the measured value exceeds the specified value, re-
tighten the clamp.
HINT:
Install the damper clamp to inboard joint side.
Except 1AZ±FSE, FE (MT)/ 1CD±FTV
Perform the above procedure only when reassembling
the RH side
38. INSTALL FRONT DRIVE INBOARD JOINT ASSY LH
(a) Wrap the spline of the outboard joint shaft assy LH with
vinyl tape to prevent them from being damaged.
(b) Install new parts to the outboard joint shaft assy LH in the
following order.
(1) Inboard joint boot LH clamp
(2) Inboard joint boot
(3) Inboard joint boot LH No.2 clamp
(c) Place the beveled side of the tripod axial spline toward the
outboard joint.
(d) Align the matchmarks placed before removal.
(e) Using a brass bar and hammer, tap in the tripod joint assy
to the drive shaft assy LH.
NOTICE:
Do not tap the roller.
Be sure to install the tripod joint assy in the correct
direction.
(f) Pack the inboard joint shaft and boot with grease in the
boot kit.
Engine typeGrease capacity g (oz.)
1AZ±FSE, 1AZ±FE, 1CD±FTV170 ± 190 g
(6.0 ± 6.7 oz.)
3ZZ±FE, 1ZZ±FE125.5 ± 135.5 g
(4.4 ± 4.8 oz.)
Page 4740 of 5135
C86268
SST
C67417
Matchmarks
G24058
− DRIVE SHAFT / PROPELLER SHAFTFRONT DRIVE SHAFT (2AZ−FSE)
30−13
AVENSIS Supplement (RM1045E)
(5) Using SST, adjust the clearance of the damper
clamp.
SST 09240−00020
Clearance: 0.8 mm (0.031in.) or less
NOTICE:
When the measured value exceeds the specified value, re-
tighten the clamp.
HINT:
SInstall the damper clamp to inboard joint side.
SPerform the above procedure only when reassembling
the RH side.
37. INSTALL FRONT DRIVE INBOARD JOINT ASSY LH
(a) Wrap the outboard joint shaft assy LH spline with vinyl
tape to prevent it from being damaged.
(b) Install new parts to the outboard joint shaft assy LH in the
following order.
(1) Inboard joint boot LH clamp
(2) Inboard joint boot
(3) Inboard joint boot LH No.2 clamp
(c) Place the beveled side of the tripod axial spline toward the
outboard joint.
(d) Align the match marks.
(e) Using a brass bar and hammer, tap in the tripod joint assy
to the drive shaft assy LH.
NOTICE:
SDo not tap the roller.
SBe sure to install the tripod joint assy in the correct
direction.
(f) Pack the inboard joint shaft and boot with grease in the
boot kit.
Grease capacity:170 to190 g (6.0 to 6.7 oz.)
(g) Using a snap ring expander, install a new shaft snap ring.