key TOYOTA AYGO 2011 Service Manual

162AUDIO SYSTEM
Reference
MS17001
AM·FM radio/compact disc player (with
compact disc changer controller)
This Section describes some of the basic
features on Toyota audiosystems. Some
information may not pertain to your sys-
tem.
Your audiosystem works when theengine
switch is in the “ACC” or “ON” position.
TURNING THE SYSTEM ON AND OFF
Push “
” (Power) to turn the audio sys-
tem on and off. The audio power can be
turned on only once even when the key
is not in the engine switch. The power,
however, will automatically turn off when
30 minutes have elapsed.
Push “AM/FM” or “CD/AUX” to turn on
that function without pushing “
” (Power).
You can turn on the compact disc player
by inserting a compact disc.
You can turn off each player by ejecting
the compact disc. If the audiosystem was
previously off, then the entire audio sys-
tem will be turned off when you eject the
compact disc. If another function was pre-
viously on, it will come on again.
SWITCHING BETWEEN FUNCTIONS
Push “AM/FM” or “CD/AUX” if the system
is already on but you want to switch from
one function to another.
VOLUME CONTROL
To adjust the volume, push and release
“”or“” side of the “VOL” button.
AYGO WE 99E37E11 02.18
Using your audio system—
—Some basics

AUDIO SYSTEM165
123456(Preset buttons)
These buttons are used to preset and
tune in radio stations.
To preset a station to a button: Tune in
the desired station. (See “TUNE/TRACK”
button). Push and hold down the button
until you hear a beep—this will set the
station to the button. The button number
will appear on the display.
To recall a preset station: Push the button
for the station you want. The button num-
ber and station frequency will appear on
the display.
These systems can store one AM and
three FM station for each button. (The
display will show “AM”, “FM1”, “FM2” or
“FM3” when you push “AM/FM”.) The pre-
set station memory will be canceled out
if the power source is interrupted. (Battery
disconnected or fuse blown.)
(Eject button)
Push this button to eject a compact disc.
After you turn the engine switch to
“LOCK”, you will be able to eject a com-
pact disc but you will not be able to rein-
sert it.
TUNE/TRACK (Tuning/Track up/down)
Radio
Tuning:
Quickly push and release the “”or“”
button. Each time you push the button,
the radio will step up or down to another
frequency. If you hear a beep, you held
the button too long and the radio will go
into the seek mode.Seeking:
Push and hold the “”or“” until you
hear a beep. The radio will begin seeking
up or down for a station of the nearest
frequency and will stop on reception. Each
time you push the button, the stations will
be searched automatically one after anoth-
er.
Compact disc player
By using this button, you can either skip
up/down to a different track or fast for-
ward/reverse the track you are listening
to.
Skip up/down tracks:
Quickly push and release the “”or“”
button. The track number will appear on
the display. If you hear a beep, you held
the button too long, and the player will
fast forward or reverse a track.
Fast forward/reverse tracks:
Push and hold the “
”or“” until
you hear a beep. While you are holding
the button, the player will fast forward/re-
verse the track. When you release the
button, the player will resume playing.
“
”(Power)
Push “
” to turn the audiosystem on
and off. The audio power can be turned
on only once even when the key is not
in the engine switch. The power, however,
will automatically turn off when 30 minutes
have elapsed.
VOL (Volume)
The volume can be adjusted by pushing
the “”or“” button.
AYGO WE 99E37E11 02.18

188OTHER EQUIPMENT
Clock
MS19005a
Before adjusting the clock.
Push the “CLOCK” button until you hear
a beep.
To reset the hour: Push the “” button.
To reset the minutes: Push the “” but-
ton.
The engine switch must be in the “ACC”
or “ON” position.
If the electrical power source has been
disconnected from the clock, the time dis-
play will automatically be set to 1:00.
When the instrument panel lights are
turned on, the brightness of the time in-
dication will be reduced.
Turning the system on and off
Push “
” (Power) to turn the audio sys-
tem on and off. The audio power can be
turned on only once even when the key
is not in the engine switch. The power,
however, will automatically turn off when
30 minutes have elapsed.
Power outlet
MS19006a
The power outlet is designed as a pow-
er supply for car accessories. To use
the power outlet, open it as shown in
the illustration.
The engine switch must be in the “ACC”
or “ON” position to be used.
NOTICE
zTo prevent the fuse from being
blown, do not use more electricity
than the total vehicle capacity of
12V/120W.
zTo prevent the battery from being
discharged, do not use the power
outlet for longer than necessary
when the engine is not running.
zClose the power outlet lid when the
power outlet is not in use. Inserting
anything other than an appropriate
plug that fits the outlet, or allowing
any liquid to get into the outlet may
cause electrical failure or short cir-
cuits.
zDo not turn car accessory plugs
when they are inserted into the
power outlet. Doing so may damage
the power outlet, depending on the
plug shape.
AYGO WE 99E37E11 02.18

STARTING AND DRIVING211
Before starting the engine, be sure to
follow the instructions in “(a) Before
cranking”.
Normal starting procedure
The multiport fuel injection system/sequen-
tial multiport fuel injection system in your
engine automatically controls the proper
air−fuel mixture for starting. You can start
a cold or hot engine as follows:
Multi−mode manual transmission:With
your foot off the accelerator pedal, turn
the engine switch to the “START” posi-
tion and crank the engine while depress-
ing the brake pedal. Release the key
when the engine starts. The engine can-
not be cranked if the shift lever is in a
position except “N” or the brake pedal
is not depressed.
Manual transmission:With your foot off
the accelerator pedal, crank the engine
by turning the engine switch to the
“START” position. Release it when the
engine starts.
Engine should be warmed up by driving,
not idling. For warming up drive with a
smoothly turning engine until the engine
coolant temperature is within the normal
range.
If the engine stalls...
Simply restart it, using the correct proce-
dure given in normal starting.
If the engine will not start...
See “If your vehicle will not start” on page
220 in Section 4.
NOTICE
zDo not crank for more than 30 se-
conds at a time. This may overheat
the starter and wiring systems.
zDo not race a cold engine.
zIf the engine becomes difficult to
start or stalls frequently, have the
engine checked immediately.
Pre−trip safety check
It is a good idea to do a safety check
before starting out on a trip. A few min-
utes of checking can help ensure safe and
pleasant driving. Just a basic familiarity
with your vehicle is required and a careful
eye! Or, if you would like, any authorized
Toyota dealer or repairer, or another duly
qualified and equipped professional, will
be pleased to make this check for you at
nominal cost.
CAUTION
If you make this check in an enclosed
garage, make sure there is adequate
ventilation. Engine exhaust is poison-
ous.
BEFORE STARTING THE ENGINE
Outside the vehicle
Tires.Check the pressure with a gauge
and look carefully for cuts, damage, or
excessive wear.
Wheel bolts.Make sure no bolts are mis-
sing or loose.
Fluid leaks.After the vehicle has been
parked for a while, check underneath for
leaking fuel, oil, water, or fluid. (Water
dripping from the air conditioning after use
is normal.)
Lights.Make sure the headlights, stop
lights, tail lights, turn signals and other
lights are all working. Check the headlight
aim.
Inside the vehicle
Spare tire, jack and wheel bolt wrench.
Check the spare tire pressure and make
sure you have your jack and wheel bolt
wrench.
AYGO WE 99E37E11 02.18
(b) Starting the engine

IN CASE OF AN EMERGENCY219
Section 4
IN CASE OF AN EMERGENCY
DIf your vehicle will not start 220..............................
DIf your engine stalls while driving 224........................
DIf you cannot increase engine speed 225.....................
DIf your vehicle overheats 225...............................
DIf you have a flat tire 226...................................
DIf your vehicle becomes stuck 236...........................
DIf your vehicle needs to be towed 236........................
DIf you cannot shift multi−mode manual transmission
shift lever 242.............................................
DIf you lose your keys 243...................................
DIf your vehicle has to be stopped in an emergency 244........
AYGO WE 99E37E11 02.18

220IN CASE OF AN EMERGENCY
Before making these checks, make sure
you have followed the correct starting
procedure given in “How to start the
engine” on page 210 in Section 3 and that
you have sufficient fuel. Since your
vehicle is equipped with an engine
immobilizer system, also check whether
the other keys will start the engine. If
they work, your key may be broken. Have
the key checked at any authorized Toyota
dealer or repairer, or another duly
qualified and equipped professional. If
none of your keys work, there may be a
malfunction in the immobilizer system. Call
any authorized Toyota dealer or repairer,
or another duly qualified and equipped
professional. (See “Keys” on page 10 in
Section 1−2).
If the engine is not turning over or is
turning over too slowly—
1. Check that the battery terminals are
tight and clean.
2. If the battery terminals are O.K., switch
on the interior light.
3. If the light is out, dim or goes out
when the starter is cranked, the battery
is discharged. You may try jump start-
ing. See “(c) Jump starting” on page
221 for further instructions.
If the light is OK, but the engine still will
not start, it needs adjustment or repair.
Call any authorized Toyota dealer or re-
pairer, or another duly qualified and
equipped professional.
NOTICE
For manual transmission:
Do not pull−or push−start the ve-
hicle. It may damage the vehicle or
cause a collision when the engine
starts. Also the three−way catalytic
converter may overheat and become a
fire hazard.
If the engine turns over at its normal
speed but will not start—
1. Turn the engine switch to “ACC” or
“LOCK” and try starting the engine
again.
2. If the engine will not start, the engine
may be flooded because of repeated
cranking. See “(b) Starting a flooded
engine” on page 221 for further instruc-
tions.
3. If the engine still will not start, it needs
adjustment or repair. Call any autho-
rized Toyota dealer or repairer, or
another duly qualified and equipped
professional.
AYGO WE 99E37E11 02.18
If your vehicle will not start
(a) Simple checks

IN CASE OF AN EMERGENCY221
If the engine will not start, your engine
may be flooded because of repeated
cranking.
If this happens, turn the engine switch to
“START” with the accelerator pedal fully
depressed. Keep the key and accelerator
pedal in these positions for 15 seconds
and release them. Then try starting the
engine with your foot off the accelerator
pedal.
If the engine does not start after 15 se-
conds of cranking, release the key, wait
a few minutes and try again.
If the engine still will not start, it needs
adjustment or repair. Call any authorized
Toyota dealer or repairer, or another duly
qualified and equipped professional, for
assistance.
NOTICE
Do not crank for more than 30 se-
conds at a time. This may overheat
the starter and wiring systems.
(c) Jump starting
To avoid serious personal injury and
damage to your vehicle which might re-
sult from a battery explosion, acid
burns, electrical burns, or damaged
electronic components, these instruc-
tions must be followed precisely.
Vehicles with multi−mode manual transmis-
sion—The engine cannot be started by
push−starting.
If you are unsure about how to follow this
procedure, we strongly recommend that
you seek the help of a competent me-
chanic or towing service.
CAUTION
DBatteries contain sulfuric acid
which is poisonous and corrosive.
Wear protective safety glasses when
jump starting, and avoid spilling
acid on your skin, clothing, or ve-
hicle.
DIf you should accidentally get acid
on yourself or in your eyes, remove
any contaminated clothing and flush
the affected area with water imme-
diately. Then get immediate medical
attention. If possible, continue to
apply water with a sponge or cloth
while en route to the medical office.
DThe gas normally produced by a
battery will explode if a flame or
spark is brought near. Use only
standardized jumper cables and do
not smoke or light a match while
jump starting.
NOTICE
The battery used for boosting must
be12 V. Do not jump start unless you
are sure that the booster battery is
correct.
AYGO WE 99E37E11 02.18
(b) Starting a flooded engine

IN CASE OF AN EMERGENCY237
Proper equipment will help ensure that
your vehicle is not damaged while being
towed. Commercial operators are generally
aware of the state/provincial and local
laws pertaining to towing.
Your vehicle could be damaged if it is
towed incorrectly. Although most operators
know the correct procedure, it is possible
to make a mistake. To avoid damage to
your vehicle, make sure the following pre-
cautions are observed. If necessary, show
this page to the tow truck driver.
TOWING PRECAUTIONS:
Use a safety chain system for all towing,
and abide by the state/provincial and local
laws. The wheels and axle on the ground
must be in good condition. If they are
damaged, use a towing dolly.
(a) Towing with wheel lift type truck
From front—Release the parking brake.
NOTICE
When lifting wheels, take care to en-
sure adequate ground clearance for
towing at the opposite end of the
raised vehicle. Otherwise, the bumper
and/or underbody of the towed vehicle
may be damaged during towing.
From rear—
DManual transmission:
We recommend using a towing dolly
under the front wheels. If you do not
use a towing dolly, place the engine
switch in the “ACC” position and put
the transmission in neutral.
DMulti−mode manual transmission:
We recommend using a towing dolly.
The towing dolly is set up under the
front wheels. If you do not use the
towing dolly (or if it is not available),
first turn the engine switch “ON” and
shift the shift lever to “N”. Make sure
that the gear is in the “N” position by
checking the gear position indicator.
Multi−mode manual transmission only:
After shifting the shift lever to the “N”
position, always make sure that the gear
is actually disengaged and is in neutral by
pushing the vehicle by hand or other
means. In case the gear can not be put
in neutral, turn the engine switch from the
“OFF” to “ON” position, and operate the
shift lever once from “N” to “E”, “M” or
“R”, then back to “N” again. Then turn the
engine switch from the “ON” to “OFF”
position. These procedures may help put
the gear in neutral. If the gear still can
not be put in neutral, you can not tow
without a towing dolly.
NOTICE
Do not tow with the key removed or
in the “LOCK” position when towing
from the rear without a towing dolly.
The steering lock mechanism is not
strong enough to hold the front
wheels straight.
(b) Using a flat bed truck
AYGO WE 99E37E11 02.18

IN CASE OF AN EMERGENCY243
DAfter shifting the shift lever to the “N”
position, always make sure that the
gear is actually disengaged and is in
neutral by pushing the vehicle by hand
or other means. In case the gear can
not be put in neutral, turn the engine
switch from the “OFF” to “ON” position,
and operate the shift lever once from
“N” to “E” or “R”, then back to “N”
again. Then turn the engine switch
from the “ON” to “OFF” position. These
procedures may help put the gear in
neutral. If the gear still can not be put
in neutral, you can not tow with cables
or chains.
6. Start the engine while depressing the
brake pedal.
Be sure to have the system checked any
authorized Toyota dealer or repairer, or
another duly qualified and equipped pro-
fessional, as soon as possible.
If you lose your keys
You can purchase a new key at any
authorized Toyota dealer or repairer, or
another duly qualified and equipped
professional, if you can give them the
key number and key.
Even if you lose only one key, contact
any authorized Toyota dealer or repairer,
or another duly qualified and equipped
professional, to make a new key. If you
lose all your keys, you cannot make new
keys; the whole engine immobilizersystem
must be replaced.
See the suggestion given in “Keys” on
page 10 in Section 1−2.
Wireless remote control key—
You can use the wireless remote control
system with the new key. Contact any
authorized Toyota dealer or repairer, or
another duly qualified and equipped pro-
fessional, for detailed information.
If your keys are locked in the vehicle and
you cannot get a duplicate, many autho-
rized Toyota dealers, repairers or other
duly qualified and equipped professionals
can still open the doors for you, using
their special tools. If you must break a
window to get in, we suggest breaking the
smallest side window because it is the
least expensive to replace. Be extremely
cautious to avoid cuts from the glass.
AYGO WE 99E37E11 02.18

244IN CASE OF AN EMERGENCY
Only in an emergency, such as if it
becomes impossible to stop the vehicle
in the normal way, stop the vehicle us-
ing the following procedure:
1. Steadily step on the brake pedal with
both feet and firmly depress it. Do not
pump the brake pedal repeatedly as
this will increase the effort required to
slow the vehicle.
2. Shift the shift lever to N.
If the shift lever is shifted to N:
3. After slowing down, stop the vehicle in
a safe place by the road.
4. Stop the engine.
If the shift lever cannot be shifted to
N:
3. Keep depressing the brake pedal with
both feet to reduce vehicle speed as
much as possible.
X40294
4. Stop the engine by turning the engine
switch to the ACC position.
5. Stop the vehicle in a safe place by the
road.
CAUTION
If the engine has to be turned off
while driving:
DPower assist for the brakes and
steering wheel will be lost, making
the brake pedal harder to depress
and the steering wheel heavier to
turn. Decelerate as much as pos-
sible before turning off the engine.
DNever attempt to remove the key, as
doing so will lock the steering
wheel.
AYGO WE 99E37E11 02.18
If your vehicle has to be
stopped in an emergency