ABS TOYOTA AYGO 2011 Owners Manual

58OCCUPANT RESTRAINT SYSTEMS
When the airbags inflate, they produce a
loud noise and release some smoke and
residue along with non−toxic gas. This
does not indicate a fire. This smoke may
remain inside the vehicle for some time,
and may cause some minor irritation to
the eyes, skin or breathing. Be sure to
wash off any residue as soon as possible
to prevent any potential skin irritation with
soap and water. If you can safely exit
from the vehicle, you should do so imme-
diately.
Deployment of the airbags happens in a
fraction of a second, so the airbags must
inflate with considerable force. While the
system is designed to reduce serious inju-
ries, primarily to the head and chest, it
may also cause other, less severe injuries
to the face, chest, arms and hands. These
are usually in the nature of minor burns
or abrasions and swelling, but the force of
a deploying airbag can cause more seri-
ous injuries, especially if an occupant’s
hands, arms, chest or head is in close
proximity to the airbag module at the time
of deployment. This is why it is important
for the occupant to: avoid placing any
object or part of the body between the
occupant and the airbag module; sit
straight and well back into the seat; wear
the available seat belt properly; and sit as
far as possible from the airbag module,
while still maintaining control of the ve-
hicle.
Parts of the airbag module (steering wheel
hub, airbag cover and inflator) may be hot
for several minutes after deployment, so
do not touch! The airbags inflate only
once. The windshield may be damaged by
absorbing some of the force of the inflat-
ing airbag.
CAUTION
The driver or front passenger who is
too close to the steering wheel or
dashboard during airbag deployment
can be killed or seriously injured.
Toyota strongly recommends that:
DThe driver sit as far back as pos-
sible from the steering wheel while
still maintaining control of the ve-
hicle.
DThe front passenger sit as far back
as possible from the dashboard.
DAll vehicle occupants must be prop-
erly restrained using the available
seat belts.
For instructions and precautions con-
cerning the seating position, see
“—Front seat precautions” on page
42 in this Section.
AYGO WE 99E37E11 02.18

GAUGES, METERS AND SERVICE REMINDER INDICATORS129
(a) Brake System Warning Light
This light comes on in the following cases
when the engine switch is in the “ON”
position.
DWhen the parking brake is applied...
This light comes on for a few seconds
when the engine switch is turned to the
“ON” position even after the parking brake
is released.
DWhen the brake fluid level is low...
CAUTION
It is dangerous to continue driving
normally when the brake fluid level is
low.
Have your vehicle checked at any au-
thorized Toyota dealer or repairer, or
another duly qualified and equipped
professional, in the following cases:
DThe light does not come on even if the
parking brake is applied when the en-
gine switch is in the “ON” position.
DThe light does not come on even if the
engine switch is turned on with the
parking brake released.
A warning light turning on briefly during
operation does not indicate a problem.
CAUTION
If either of the following conditions
occurs, immediately stop your vehicle
at a safe place and contact any au-
thorized Toyota dealer or repairer, or
another duly qualified and equipped
professional.
DThe light does not turn off even
after the parking brake is released
while the engine is running.
In this case, the brakes may not
work properly and your stopping
distance will become longer. De-
press the brake pedal firmly and
bring the vehicle to an immediate
stop.
DThe brake system warning light re-
mains on together with the “ABS”
warning light.
In this case, not only the anti−lock
brake system will fail but also the
vehicle will become extremely un-
stable during braking.
(b) Driver ’s Seat Belt Reminder Light
and Buzzer
The light and buzzer act as a reminder to
buckle up the driver ’s seat belt.
Once the engine switch is turned to “ON”
or “START”, the reminder light flashes if
the driver ’s seat belt is not fastened. Un-
less the driver fastens the belt, the light
continues flashing.
If the vehicle speed rises above 20 km/h
(12 mph) with the seat belt unfastened,
the buzzer will sound for 30 seconds.
Then, if the seat belt is still unfastened,
the buzzer will sound in a different tone
for 90 more seconds. Even if the vehicle
speed drops below 20 km/h (12 mph), the
buzzer will continue to sound. To stop the
buzzer, fasten the seat belt. If the buzzer
still sounds, make sure the front passen-
ger ’s seat belt is fastened.
AYGO WE 99E37E11 02.18

132GAUGES, METERS AND SERVICE REMINDER INDICATORS
(i) Engine Coolant Temperature Warn-
ing Light
This light comes on or blinks in the fol-
lowing cases:
DThe light will come on when the engine
switch is turned to the “ON” position.
After a few seconds, the light will go
off.
DWhen the engine coolant temperature
becomes high, the engine coolant tem-
perature warning light blinks. If the
temperature rises further, the engine
coolant temperature warning light re-
mains on and the “STOP” warning light
blinks at the same time. In such cases,
stop the vehicle and check the engine.
For detailed instructions, see “If your
vehicle overheats” on page 225 in Sec-
tion 4.
NOTICE
Continuing to drive when the engine
coolant temperature warning light is
blinking or the engine coolant temper-
ature warning light remains on and
the “STOP” warning light is blinking
at the same time, could result in the
engine overheating.
(j) “Multi−mode Manual Transmission”
Warning Light (Multi−mode manual
transmission only)
This light will come on when the engine
switch is turned to the “ON” position. After
a few seconds, the light will go off. This
means the multi−mode manual transmis-
sion system isoperating properly.
NOTICE
In case the Multi−mode manual trans-
mission warning light comes on, pull
over, stop the engine and contact any
authorized Toyota dealer or repairer,
or another duly qualified and
equipped professional. Otherwise, the
vehicle may jerk when shifted gear or
the clutch may not engage properly.
In some cases the shift requirement
may be canceled and the gear may be
locked.
(k) “ABS” Warning Light
Vehicles without vehicle stability control
system—
The light comes on when the engine
switch is turned to the “ON” position. If
the anti−lock brake system works properly,
the light turns off after a few seconds.
Thereafter, if the system malfunctions, the
light comes on again.
When the “ABS” warning light is on (and
the brake system warning light is off), the
anti−lock brake systemdoes not operate,
but the brake system stilloperates con-
ventionally.
When the “ABS” warning light is on (and
the brake system warning light is off), the
anti−lock brake systemdoes not operate
so that the wheels could lock up during
sudden braking or braking on slippery
road surfaces.
AYGO WE 99E37E11 02.18

GAUGES, METERS AND SERVICE REMINDER INDICATORS133
If either of the following conditions
occurs, this indicates a malfunction
somewhere in the components moni-
tored by the warning light system.
Contact any authorized Toyota dealer or
repairer, or another duly qualified and
equipped professional, as soon as
possible to service the vehicle.
DThe light does not come on when the
engine switch is turned to the “ON”
position, or remains on.
DThe light comes on while you are driv-
ing.
A warning light turning on briefly during
operation does not indicate a problem.
CAUTION
If the “ABS” warning light remains on
together with the brake system warn-
ing light, immediately stop your ve-
hicle at a safe place and contact any
authorized Toyota dealer or repairer,
or another duly qualified and
equipped professional.
In this case, not only the anti−lock
brake system will fail but also the
vehicle will become extremely unsta-
ble during braking.
Vehicles with vehicle stability control sys-
tem—
The light comes on when the engine
switch is turned to the “ON” position. If
the anti−lock brake system and the brake
assist system work properly, the light
turns off after a few seconds. Thereafter,
if either of the system malfunctions, the
light comes on again.
When the “ABS” warning light is on (and
the brake system warning light is off), the
anti−lock brake system, the brake assist
system, the traction control system and
the vehicle stability control system do not
operate, but the brakesystem stilloper-
ates conventionally.When the “ABS” warning light is on (and
the brake system warning light is off), the
anti−lock brake systemdoes not operate
so that the wheels could lock up during a
sudden braking or braking on slippery
road surfaces.
If either of the following conditions
occurs, this indicates a malfunction
somewhere in the components moni-
tored by the warning light system,
contact any authorized Toyota dealer or
repairer, or another duly qualified and
equipped professional, as soon as
possible to service the vehicle.
DThe light does not come on when the
engine switch is turned to the “ON”
position, or remains on.
DThe light comes on while you are driv-
ing.
A warning light turning on briefly during
operation does not indicate a problem.
CAUTION
If the “ABS” warning light remains on
together with the brake system warn-
ing light, immediately stop your ve-
hicle at a safe place and contact any
authorized Toyota dealer or repairer,
or another duly qualified and
equipped professional.
In this case, not only the anti−lock
brake system will fail but also the
vehicle will become extremely unsta-
ble during braking.
(l) “VSC” Warning Light
This light warns that there is a problem
somewhere in the vehicle stability control
system or traction control system.
The light will come on when the engine
switch is turned to the “ON” position and
will go off after a few seconds.
AYGO WE 99E37E11 02.18

GAUGES, METERS AND SERVICE REMINDER INDICATORS135
CAUTION
If the electric power steering system
warning light comes on, take your ve-
hicle to any authorized Toyota dealer
or repairer, or another duly qualified
and equipped professional, as soon
as possible. In this case, more effort
is required for the steering wheel to
turn than usual. Drive your vehicle
while firmly gripping the steering
wheel.
(o) Light Reminder Buzzer
This buzzer will sound if the driver ’s door
is opened while the engine switch is
turned to the “LOCK” position with the
headlight switch on. Removing the key will
not stop the buzzer as long as the head-
light switch is on.
(p) Warning function of the Multi−mode
manual transmission (Multi−mode
manual transmission only)
When driving, if any incorrect operation
that may cause damage to this system is
performed or if the gear is not shifted as
desired by the driver, the warning buzzer
will sound and the gear position indicator
will blink to warn the driver in some
cases. For details, see “—Warning
functions” on page 154 in Section 1−7.
When the shift lever is shifted to “R”, the
reverse buzzer sounds once. This is to
indicate the shift lever position, not a
malfunction. For details, see “(d) Backing
up” on page 143 or 150 in Section 1−7.CHECKING SERVICE REMINDER
INDICATORS (except the low fuel level
warning light)
1. Apply the parking brake.
2. Turn the engine switch to the “ON”
position, but do not start the engine.
All the service reminder indicators should
come on. The “ABS”, “VSC”, “STOP”, en-
gine coolant temperature, Multi−mode
manual transmission warning lights and
electric power steering system warning
lights go off after a few seconds. The
SRS warning light goes off after 6 sec-
onds.
If any service reminder indicator or warn-
ing buzzer does not function as described
above, have it checked by any authorized
Toyota dealer or repairer, or another duly
qualified and equipped professional, as
soon as possible.
AYGO WE 99E37E11 02.18

200INFORMATION BEFORE DRIVING YOUR TOYOTA
Brake system
The tandem master cylinder brakesystem
is a hydraulic system with two separate
sub−systems. If either sub−system should
fail, the other will still work. However, the
pedal will be harder to press, and your
stopping distance will increase. Also, the
brake system warning light may come on.
CAUTION
Do not drive your vehicle with only a
single brake system. Have your
brakes fixed immediately.
BRAKE BOOSTER
The brake booster uses engine vacuum to
power−assist the brakes. If the engine
should quit while you are driving, you can
bringthevehicletoastopwithnormal
pedal pressure. There is enough reserved
vacuum for one or two stops—but no
more!
CAUTION
DDo not pump the brake pedal if the
engine stalls. Each push on the
pedal uses up the reserved vacuum.
DEven if the power assist is com-
pletely lost, the brakes will still
work. But you will have to push the
pedal hard, much harder than nor-
mal. And your braking distance will
increase.
ANTI−LOCK BRAKE SYSTEM
The anti−lock brake system is designed
to help prevent lock−up of the wheels
during a sudden braking or braking on
slippery road surfaces. This assists in
providing directional stability and steer-
ing performance of the vehicle under
these circumstances.
Effective way to press the ABS brake
pedal:
When the anti−lock brake system func-
tion is in action, you may feel the brake
pedal pulsating and hear a noise. In this
situation, to let the anti−lock brake sys-
tem work for you, just hold the brake
pedal down more firmly. Do not pump
the brake in a panic stop. This will re-
sult in reduced braking performance.
The anti−lock brake system becomes op-
erative after the vehicle has accelerated
to a speed in excess of approximately 10
km/h (6 mph). It stops operating when the
vehicle decelerates to a speed below
approximately 5 km/h (3 mph).
Depressing the brake pedal on slippery
road surfaces such as on a manhole cov-
er, a steel plate at a construction site,
joints in a bridge, etc. on a rainy day
tends to activate the anti−lock brake sys-
tem.
You may hear a click or motor sound in
the engine compartment for a few seconds
when the engine is started or just after
the vehicle begins to move. This means
that the anti−lock brake system is in self−
check mode, and does not indicate a mal-
function.
When the anti−lock brake system is ac-
tivated, the following conditions may
occur. They do not indicate a malfunc-
tion of the system:
AYGO WE 99E37E11 02.18

202INFORMATION BEFORE DRIVING YOUR TOYOTA
MS21009
“ABS” warning light
Vehicles without vehicle stability control
system—
The light comes on when the engine
switch is turned to the “ON” position. If
the anti−lock brake system works properly,
the light turns off after a few seconds.
Thereafter, if the system malfunctions, the
light comes on again.
When the “ABS” warning light is on (and
the brake system warning light is off), the
anti−lock brake systemdoes not operate,
but the brake system stilloperates con-
ventionally.
When the “ABS” warning light is on (and
the brake system warning light is off), the
anti−lock brake systemdoes not operate
so that the wheels could lock up during
a sudden braking or braking on slippery
road surfaces.
If either of the following conditions oc-
cur, this indicates a malfunction some-
where in the components monitored by
the warning light system. Contact any
authorized Toyota dealer or repairer, or
another duly qualified and equipped
professional, as soon as possible to
service the vehicle.
DThe light does not come on when the
engine switch is turned to the “ON”
position, or remains on.
DThe light comes on while you are driv-
ing.
A warning light turning on briefly during
operation does not indicate a problem.
CAUTION
If the “ABS” warning light remains on
together with the brake system warn-
ing light, immediately stop your ve-
hicle at a safe place and contact any
authorized Toyota dealer or repairer,
or another duly qualified and
equipped professional.
In this case, not only the anti−lock
brake system will fail but also the
vehicle will become extremely unsta-
ble during braking.
“ABS” warning light
Vehicles with vehicle stability control sys-
tem—
The light comes on when the engine
switch is turned to the “ON” position. If
the anti−lock brake system and the brake
assist system work properly, the light
turns off after a few seconds. Thereafter,
if the system malfunctions, the light
comes on again.
When the “ABS” warning light is on (and
the brake system warning light is off), the
anti−lock brake system, the brake assist
system, the traction control system and
the vehicle stability control system do not
operate, but the brakesystem stilloper-
ates conventionally.
When the “ABS” warning light is on (and
the brake system warning light is off), the
anti−lock brake systemdoes not operate
so that the wheels could lock up during a
sudden braking or braking on slippery
road surfaces.
AYGO WE 99E37E11 02.18

INFORMATION BEFORE DRIVING YOUR TOYOTA203
If either of the following conditions oc-
curs, this indicates a malfunction some-
where in the components monitored by
the warning light system. Contact any
authorized Toyota dealer or repairer, or
another duly qualified and equipped
professional, as soon as possible to
service the vehicle.
DThe light does not come on when the
engine switch is turned to the “ON”
position or remains on.
DThe light comes on while you are driv-
ing.
A warning light turning on briefly during
operation does not indicate a problem.
CAUTION
If the “ABS” warning light remains on
together with the brake system warn-
ing light, immediately stop your ve-
hicle at a safe place and contact any
authorized Toyota dealer or repairer,
or another duly qualified and
equipped professional.
In this case, not only the anti−lock
brake system will fail but also the
vehicle will become extremely unsta-
ble during braking.
BRAKE ASSIST SYSTEM
When you slam the brakes on, the
brake assist system judges as an emer-
gency stop and provides more powerful
braking for a driver who cannot hold
down the brake pedal firmly.
When you slam the brakes on, more pow-
erful braking will be applied. At this time,
you may hear a sound in the engine
compartment and feel the vibrations of the
brake pedal. This does not indicate a mal-
function.Vehicles with vehicle stability control sys-
tem—
The brake assist system becomesopera-
tive after the vehicle has accelerated to a
speed in excess of approximately 10 km/h
(6 mph). It stops operating when the ve-
hicle decelerates to a speed below
approximately 5 km/h (3 mph).
For an explanation of thissystem’s warn-
ing light, see “Service reminder indicators
and warning buzzers” on page 127 in Sec-
tion 1−6.
AYGO WE 99E37E11 02.18

284DO−IT YOURSELF MAINTENANCE: Electrical components
MS73002b
2. Release the bulb retaining spring
and remove the bulb. Install a new
bulb and the bulb retaining spring.
To install a bulb, align the tabs of the
bulb with the cutouts of the mounting
hole.
MS73003
3. Install the rubber cover as shown
and fit it securely on the boss. Plug
in the connector.
Make sure the rubber cover fits securely
on the connector and the headlight body.
Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact any authorized Toyota
dealer or repairer, or another duly quali-
fied and equipped professional.
AYGO WE 99E37E1102.18

SPECIFICATIONS301
Fuses (type A)
1. H−LP RH (HI) 10 A (with daytime
running light system):Right−hand
headlights
2. H−LP LH (HI) 10 A (with daytime run-
ning light system):Left−hand head-
lights, gauges and meters
3. H−LP RH (LO) 10 A (with daytime
running light system):Right−hand
headlights
4. H−LP LH (LO) 10 A (with daytime
running light system):Left−hand
headlights, gauges and meters
5. DIMMER 20 A (with daytime running
light system):“H−LP LH (HI)”, “H−LP
RH(HI)”, “H−LP LH (LO)”, “H−LP RH
(LO)” fuses, daytime running light sys-
tem
H−LP LH 10 A (without daytime run-
ning light system):Left−hand head-
lights
6. ABS NO.2 25 A (without vehicle sta-
bility controlsystem):Anti−lock brake
systemand vehicle stability control sys-
tem
VSC NO.2 30 A (with vehicle stability
control system):Anti−lock brake sys-
tem and vehicle stability control system
7.AM230A:Starting system, “IG1”,
“IG2”, “STA” fuses
8. HAZARD 10 A:Turn signal lights,
emergency flashers, gauges and meter-
s
9. H−LP RH 10 A (without daytime run-
ning light system):Right−hand head-
lights
10. DOME 15 A:Gauges and meters, inte-
rior light, audiosystem, tachometer
11 . E F I 1 5 A :Electric cooling fan, multi-
port fuel injection system/sequential
multiport fuel injection system
12. HORN 10 A:Horn
13. SPARE 7.5 A:Spare fuse
14. SPARE 10 A:Spare fuse15. SPARE 15 A:Spare fuse
16. STA 7.5 A:Multi−mode manual trans-
mission, multiport fuel injection system/
sequential multiport fuel injection
system
17. EFI NO.2 7.5 A:Multiport fuel injection
system/sequential multiport fuel injec-
tion system, multi−mode manual trans-
mission
18. STOP 10 A:Stop lights, high mounted
stoplight, anti−lock brake system, mul-
ti−mode manual transmission
19. D/L 25 A:Power door locksystem,
wireless remote control system
20. DEF 20 A:Rear window defogger
21. TAIL 7.5 A:Daytime running light sys-
tem, tail lights, license plate lights,
position lights, headlight beam level
control system, instrumentpanel lights
22. OBD 7.5 A:On−board diagnosis sys-
tem
23. ECU−B7.5A:Multi−mode manual
transmission, daytime running light sys-
tem, vehicle stability control system,
gauges and meters, rear fog light
24. ECU−IG 7.5 A:Anti−lock brake system,
vehicle stability control system, electric
power steering system, electric cooling
fan
25. BACK UP 10 A:Back−up lights, power
door locksystem, wireless remote con-
trol system, power windows, rear win-
dow defogger, tachometer, air condition-
ing system,heatersystem
26. WIP 20 A:Windshield wiper and wash-
er, rear window wiper and washer
27. ACC 15 A:Power outlet, audiosystem
AYGO WE 99E37E11 02.18