turn signal TOYOTA AYGO 2011 Owners Manual

OVERVIEW OF INSTRUMENTS AND CONTROLS3
MS11002a
1. Headlight, turn signal and rear fog
light switches
2. Wiper and washer switches
3. Rear window defogger switch
4. Audio system
5. Emergency flasher switch
6. Air conditioning switch
7. Air conditioning controls8. Power outlet
9. Engine switch
10. Tilt steering lock release lever
11. Airbag manual on−off switch
12. Hood lock release lever
13. Headlight beam level control switch
AYGO WE 99E37E11 02.18

OVERVIEW OF INSTRUMENTS AND CONTROLS5
MS11004a
1. Rear window defogger switch
2. Emergency flasher switch
3. Audio system
4. Air conditioning switch
5. Headlight, turn signal and rear fog
light switches
6. Wiper and washer switches7. Headlight beam level control switch
8. Airbag manual on−off switch
9. Engine switch
10. Tilt steering lock release lever
11. Power outlet
12. Air conditioning controls
AYGO WE 99E37E11 02.18

8OVERVIEW OF INSTRUMENTS AND CONTROLS
Engine preheating indicator light
Electric power steering system warning light∗
Turn signal indicator lights
Headlight high beam indicator light
Headlight low beam indicator light
Rear fog light indicator light
Slip indicator light
∗: For details, see “Service reminder indicators and warning
buzzers” on page 127 in Section 1−6.
AYGO WE 99E37E11 02.18

KEYS AND DOORS19
If the wireless remote control key does
not actuate the doors, or does not operate
from a normal distance:
DCheck for closeness to a radio trans-
mitter such as a radio station or an
airport which can interfere with normal
operation of the key.
DThe battery may have been consumed.
Check the battery in the key. To
replace the battery, see “—Replacing
battery” on page 20.
If you lose your wireless remote control
key, contact any authorized Toyota dealer
or repairer, or another duly qualified and
equipped professional, as soon as pos-
sible to avoid the possibility of theft, or an
accident. (See “If you lose your keys” on
page 243 in Section 4.)
MS12002a
Locking operation
MS12003a
Unlocking operation
To lock and unlock all the side doors
and back door, push the switches of
the key slowly and securely.
To lock: Push the “
”(LOCK)switch.All
the side doors and back door will be
locked simultaneously. At this time, the
turn signal lights flash once.
Check to see that the doors are securely
locked.
To unlock: Push the “
” (UNLOCK)
switch. All the side doors and back door
are unlocked simultaneously. At this time,
the turn signal lights flash twice.
AYGO WE 99E37E11 02.18
—Locking and unlocking
doors

LIGHTS, WIPERS AND DEFOGGER11 5
Section 1−5
OPERATION OF INSTRUMENTS AND
CONTROLS
Lights, Wipers and Defogger
DHeadlights and turn signals 116.............................
DHeadlight beam level control 117............................
DEmergency flashers 118....................................
DRear fog light 119..........................................
DInterior light 119...........................................
DWindshield wiper and washer 120...........................
DRear window wiper and washer 120.........................
DRear window defogger 121.................................
AYGO WE 99E37E11 02.18

11 6LIGHTS, WIPERS AND DEFOGGER
Headlights and turn signals
MS14001b
HEADLIGHTS
To turn on the following lights: Twist
the headlight/turn signal lever knob.
Position 1—Position, tail, license plate and
instrument panel lights
Position 2—Headlights and all of the
above
However, on some models, all the lights
above also turn on when the engine is
started with the headlight switch off.
The headlight low beam indicator light
(green light) on the instrument cluster will
tell you that the low beams are on.
Adjust the headlight beam level before
turning on the headlights. (See “Headlight
beam level control” on page 117.)
Light reminder buzzer
A buzzer will remind you to turn the lights
off when the driver ’s door is opened if the
engine switch is turned to the “LOCK”
position with the headlights switch on.
NOTICE
To prevent the battery from being dis-
charged, do not leave the lights on
for a long period when the engine is
not running.
MS14002b
High−Low beams—For high beams, turn
the headlights on and push the lever away
from you (position 1). Pull the lever to-
ward you (position 2) for low beams.
The headlight low beam indicator light
(green light) on the instrument cluster will
tell you that the low beams are on.
The headlight high beam indicator light
(blue light) on the instrument cluster will
tell you that the high beams are on.
Flashing the high beam headlights
(position 3)—Pull the lever all the way
back. The high beam headlights turn off
when you release the lever.
You can flash the high beam headlights
with the knob turned to “OFF”.
AYGO WE 99E37E11 02.18

LIGHTS, WIPERS AND DEFOGGER11 7
MS14003b
TURN SIGNALS
To signal a turn, push the headlight/
turn signal lever up or down to position
1.
The engine switch must be in the “ON”
position.
The lever automatically returns after you
make a turn, but you may have to return
it by hand after you change lanes.
To signal a lane change, move the lever
up or down to the pressure point (position
2) and hold it.
If the turn signal indicator lights (green
lights) on the instrument cluster flash fast-
er than normal, a front or rear turn signal
bulb has burned out.
Headlight beam level control
MS14004a
To adjust the headlight beam level, turn
the switch.
The following list shows examples of prop-
er switch settings. For loading conditions
other than those listed, adjust the dial
position so that the beam level is the
same as the one obtained according to
the list when only the driver is in the
vehicle. The higher the number of the dial
position, the lower the headlight beam lev-
el.
CAUTION
Always keep the headlight beam at
the proper level, or your headlights
may dazzle other road users, causing
unexpected accidents.
AYGO WE 99E37E11 02.18

11 8LIGHTS, WIPERS AND DEFOGGER
"Vehicle category M1
∗
Loading condition
Indication
figure of
control switch
Driver only or
Driver + one
passenger in the front
seat.
0
All passengers.1
All passengers and
Full luggage loading
to the luggage room.
2
Driver and
Full−luggage loading
to the luggage room.
3
"Vehicle category N1∗
Loading condition
Indication
figure of
control switch
Driver only0
Driver and
Full−luggage loading
to the luggage room
2
∗: To distinguish the vehicle category, ask
any authorized Toyota dealer or repair-
er, or another duly qualified and
equipped professional.
Emergency flashers
MS14005a
To turn on the emergency flashers,
push the switch.
All the turn signal lights will flash. To turn
them off, push the switch once again.
Turn on the emergency flashers to warn
other drivers if your vehicle must be
stopped where it might be a traffic hazard.
Always pull as far off the road as pos-
sible.
The turn signal light switch will not work
when the emergency flashers are operat-
ing.
NOTICE
To prevent the battery from being dis-
charged, do not leave the switch on
longer than necessary when the en-
gine is not running.
AYGO WE 99E37E11 02.18

LIGHTS, WIPERS AND DEFOGGER11 9
Rear fog light
MS14006a
To turn on the rear fog light, twist the
band of the headlight and turn signal
switch lever to the position of the rear
fog light. They will come on when the
headlights are on.
The rear fog light indicator on the instru-
ment cluster will light up when the rear
fog light is turned on.
The rear fog light will go off automatically
when all other lights are turned off.
After the headlight switch is turned off,
the rear fog light does not come on even
if you turn on the headlight switch again.
To turn on the rear fog light, twist the
band of the headlight and turn the signal
switch lever to the position of the rear fog
light again under the condition stated
above.
Interior light
MS14007
To turn on the interior light, slide the
switch.
The interior light switch has the following
positions:
“
” (ON)—Keeps the light on all the
time.
“
” (OFF)—Turns the light off.
“
” (DOOR)—Turns the light on when
the driver ’s door is opened.
AYGO WE 99E37E11 02.18

AUDIO SYSTEM169
SCAN
There are two scan features—you can ei-
ther scan the tracks on a specific disc or
scan the first tracks of all the discs in the
magazine.
Scanning the tracks on a disc:
Quickly push and release “SCAN”. “SCAN”
will appear on the display and the player
will scan all the tracks on the disc you
are listening to. If you hear a beep, you
held the button too long, and the player
will scan the first tracks of all the discs
in the magazine. To select a track, push
the “SCAN” a second time. If the player
scanned all the tracks on the disc, it will
stop scanning.
Compact disc changer only—
Scanning for the first tracks of all the
discs in the magazine:
Push and hold “SCAN” until you hear a
beep. “D−SCAN” will appear on the dis-
play and the player will perform the first
track of the next disc. To select a disc,
push the “SCAN” a second time. If the
player has scanned all the discs, it will
stop scanning.
ST (Stereo reception) display
Your radio automatically changes to stereo
reception when a stereo broadcast is re-
ceived. “ST” appears on the display. If the
signal becomes weak, the radio reduces
the amount of channel separation to prev-
ent the weak signal from creating noise.
If the signal becomes extremely weak, the
radio switches from stereo to mono recep-
tion.TA (Traffic Announcement)
This button is used for receiving TA sta-
tions all over the band.
EON (Enhanced Other Network) sys-
tem—If the RDS station (with EON data)
you are listening to is not broadcasting a
traffic information program at the TA (Traf-
fic Announcement) mode, the radio will be
switched to the traffic information program
automatically by using the EON AF list.
After the traffic information ends, the radio
will return to the initial program automati-
cally. A beep will sound to tell you when
this feature starts and ends the operation.
When receiving FM:
Push “TA” to switch the radio mode to TP
(Traffic Program). “TP” will appear on the
display.
In the TP mode, the radio will begin seek-
ing a TP station. If the radio seek out a
TP station, the program name will appear
on the display. If the TA station is re-
ceived, the radio will be switched to the
traffic information program automatically.
When the program ends, the initial opera-
tion resumes. When also in AF mode, the
radio will seek a TP station by using the
AF list.
Push “TA” once again to switch the radio
mode to TA. “TA” will appear on the dis-
play and the radio will mute the volume
of FM station.
In the TA mode, the radio will begin seek-
ing a TP station. It sounds only when a
TP station is received. When a TP station
is received, the program service name will
appear on the display. In the AF mode,
the radio will also begin seeking a TP
station by using the AF list.
While the radio is seeking a TP station,
“TP SEEK” appears on the display. If the
radio cannot seek out any TP stations,
“NOTHING” will appear on the display for
2 seconds and the radio will begin seek-
ing a TP station again.
AYGO WE 99E37E11 02.18