tire pressure TOYOTA C-HR 2016 Owners Manual

TABLE OF CONTENTS6
C-HR_OM_Europe_OM10528E
7-1. Maintenance and care
Cleaning and protecting
the vehicle exterior ..........600
Cleaning and protecting
the vehicle interior ...........605
7-2. Maintenance
Maintenance
requirements....................609
7-3. Do-it-yourself
maintenance
Do-it-yourself service
precautions ......................612
Hood ..................................615
Positioning a floor jack .......617
Engine compartment..........618
Tires ...................................631
Tire inflation pressure ........644
Wheels ...............................646
Air conditioning filter ..........649
Wireless remote control/
electronic key battery.......652
Checking and
replacing fuses ................656
Light bulbs .........................661
8-1. Essential information
Emergency flashers .......... 680
If your vehicle has
to be stopped
in an emergency ............. 681
8-2. Steps to take
in an emergency
If your vehicle needs
to be towed ..................... 683
If you think something
is wrong ........................... 691
Fuel pump shut off
system............................. 692
If a warning light turns
on or a warning buzzer
sounds ............................ 693
If a warning message
is displayed ..................... 704
If you have a flat tire
(vehicles with
an emergency tire
puncture repair kit) .......... 710
If you have a flat tire
(vehicles with
a spare tire) ..................... 730
7Maintenance and care8When trouble arises

15Pictorial index
C-HR_OM_Europe_OM10528E
Windshield wipers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 278
Precautions for winter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 470
To prevent freezing (windshield wiper de-icer*3) . . . . . . . . . . . P. 570
Precautions for using a car wash . . . . . . . . . . . . . . . . . . . . . . P. 602
Fuel filler door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 285
Refueling method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 285
Fuel type/fuel tank capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 764
Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 631
Tire size/inflation pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 772
Winter tires/tire chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 470
Checking/rotation/tire pressure warning system . . . . . . . . . . . P. 631
Coping with flat tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 710, 730
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 615
Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 615
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 765
Coping with overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 756
Headlights/front position lights/daytime running lights/
turn signal lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 255, 265
Front fog lights*3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 276
Side turn signal lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 255
Stop lights/tail lights/turn signal lights . . . . . . . . . . . . P. 255, 265
Tail lights (LED type) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 265
Back-up light
Shifting the shift lever to R. . . . . . . . . . . . . . . . . . . . . . . . P. 244, 250
License plate lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 265
Rear fog light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 276
4
5
6
7
Light bulbs of the exterior lights for driving
(Replacing method: P. 661, Watts: P. 773)
*1: Vehicles with a smart entry & start system
*2: Vehicles with monochrome display
*3: If equipped
8
9
10
11
12
13
14

1112. Instrument cluster
2
Instrument cluster
C-HR_OM_Europe_OM10528E
*1: These lights turn on when the engine switch is turned to the “ON” position
(vehicles without a smart entry & start system) or IGNITION ON mode
(vehicles with a smart entry & start system) to indicate that a system check
is being performed. They will turn off after the engine is started, or after a
few seconds. There may be a malfunction in a system if a light does not
come on, or if the lights do not turn off. Have the vehicle inspected by any
authorized Toyota retailer or Toyota authorized repairer, or any reliable
repairer.
*2: The light comes on to indicate a malfunction.
*3: The light flashes to indicate a malfunction.
*4: Vehicles with monochrome display
*4LDA indicator (yellow) (if equipped) P. 696
*3Stop & Start cancel indicator (if equipped) P. 697
*3Parking brake indicator P. 697
Low fuel level warning light P. 697
Driver’s and front passenger’s seat belt
reminder light P. 6 9 7
Rear passengers’ seat belt reminder lights (on
the center panel) P. 6 9 7
*1Tire pressure warning light P. 698
*1Master warning light P. 698
Warning lightsPages

1262. Instrument cluster
C-HR_OM_Europe_OM10528E
●PCS (Pre-Collision System) (if equipped) (P. 298)
● LDA (Lane Departure Alert with steering control) (if equipped)
( P. 315)
The settings of the following items can be changed.
● Language
Select to change the language on the display. ( P. 779)
● Units
Select to change the units for measure of the fuel consumption.
( P. 779)
● Eco Driving Indicator Light (vehicles with a Multidrive)
Select to activate/deactivate the Eco Driving Indicator Light.
( P. 779)
● Tire pressure warning system (if equipped)
Select to initialize the tire pressure warning system. ( P. 634)
■When disconnecting and reconnecting battery terminals
The following information data will be reset:
● Elapsed time
● Average fuel consumption
● Driving range
● Average vehicle speed
■ Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is
characteristic of liquid crystal displays, and there is no problem to continue
using the display.
■ Setting display automatic suspension
In the following situations, the setting display will be suspended.
● When a message appears
● When the vehicle begins to move
Vehicle settings
Meter settings

1332. Instrument cluster
2
Instrument cluster
C-HR_OM_Europe_OM10528E
●Vehicle Settings
Select the menu to set up the following items.
• RSA (Road Sign Assist) setup ( P. 335)*1
Select to set up RSA (Road Sign Assist).
• (Stop & Start system) setup (P. 379)*1
Select to set up Stop & Start system priority.
• (Tire pressure warning system) setup (P. 634)
Select to initialize the tire pressure warning system.
●Meter settings
Select the menu to set up the following items.
• Language
Select to change the language on the display.
•Units
Select to change the unit of measure for fuel consumption.
• (Eco Driving Indicator Light) setup*1
Select to activate/deactivate the Eco Driving Indicator Light
• Drive information 1 through 3
Select to select up to 2 items that will be displayed on a Drive informa-
tion screen, up to 3 Drive information screens can be set.
• Pop-up display
Select to set the pop-up displays*2, which may appear in some situa-
tions, on/off.
• Default settings
Registered or changed meter settings will be deleted or returned to their
default setting.
*1: If equipped
*2: Stop & Start system operation time display (if equipped), route guidance
display of the navigation system-linked system (if equipped) and incom-
ing call display of the hands-free phone system (if equipped).

2254-1. Before driving
4
Driving
C-HR_OM_Europe_OM10528E
■Information tag (manufacturer’s label)
Gross vehicle mass
The combined weight of the driver, passengers, luggage, towing hitch,
total curb mass and drawbar load should not exceed the gross vehicle
mass by more than 100 kg (220.5 lb.). Exceeding this weight is danger-
ous.
Maximum permissible rear axle capacity
The weight borne by the rear axle should not exceed the maximum per-
missible rear axle capacity by 15% or more. Exceeding this weight is
dangerous.
The values for towing capacity were derived from testing conducted at
sea level. Take note that engine output and towing capacity will be
reduced at high altitudes.
1
2
Ty pe AType B
WARNING
■ When the gross vehicle mass or maximum permissible axle capacity is
exceeded
Failing to observe this precaution may lead to an accident causing death or
serious injury.
● Add an additional 20.0 kPa (0.2 kgf/cm2 or bar, 3 psi) to the recommended
tire inflation pressure value. ( P. 772)
● Do not exceed the established speed limit for towing a trailer in built-up
areas or 100 km/h (62 mph), whichever is the lower.

2274-1. Before driving
4
Driving
C-HR_OM_Europe_OM10528E
■Tire information
● Increase the tire inflation pressure to 20.0 kPa (0.2 kgf/cm2 or bar, 3 psi)
greater than the recommended value when towing. ( P. 772)
● Increase the air pressure of the trailer tires in accordance with the total
trailer weight and according to the values recommended by the manufac-
turer of your trailer.
■ Tr a i l e r l i g h ts
Please consult at any authorized retailer or Toyota authorized repairer, or any
reliable repairer when installing trailer lights, as incorrect installation may
cause damage to the vehicle’s lights. Please take care to comply with your
state’s laws when installing trailer lights.
■ Break-in schedule
Toyota recommends that vehicles fitted with new power train components
should not be used for towing trailers for the first 800 km (500 miles).
■ Safety checks before towing
● Check that the maximum load limit for the towing hitch/bracket and hitch ball
is not exceeded. Bear in mind that the coupling weight of the trailer will add
to the load exerted on the vehicle. Also make sure that the total load exerted
on the vehicle is within the range of the weight limits. ( P. 224)
● Ensure that the trailer load is secure.
● Supplementary outside rear view mirrors should be added to the vehicle if
the traffic behind cannot be clearly seen with standard mirrors. Adjust the
extending arms of these mirrors on both sides of the vehicle so that they
always provide maximum visibility of the road behind.
■ Maintenance
● Maintenance must be performed more frequently when using the vehicle for
towing due to the greater weight burden placed on the vehicle compared to
normal driving.
● Retighten all bolts securing the hitching ball and bracket after towing for
approximately 1000 km (600 miles).

3134-5. Using the driving support systems
4
Driving
C-HR_OM_Europe_OM10528E
● In some situations such as the following, sufficient braking force may not be
obtained, preventing the system from performing properly:
• If the braking functions cannot operate to their full extent, such as when
the brake parts are extremely cold, extremely hot, or wet
• If the vehicle is not properly maintained (brakes or tires are excessively
worn, improper tire inflation pressure, etc.)
• When the vehicle is being driven on a gravel road or other slippery sur-
face
● Some pedestrians such as the following may not be detected by the radar
sensor and camera sensor, preventi ng the system from operating properly*:
• Pedestrians shorter than approximately 1 m (3.2 ft.) or taller than approx-
imately 2 m (6.5 ft.)
• Pedestrians wearing oversized clothing (a rain coat, long skirt, etc.), mak-
ing their silhouette obscure
• Pedestrians who are carrying large baggage, holding an umbrella, etc.,
hiding part of their body
• Pedestrians who are bending forward or squatting
• Pedestrians who are pushing a stroller, wheelchair, bicycle or other vehi-
cle
• Groups of pedestrians which are close together
• Pedestrians who are wearing wh ite and look extremely bright
• Pedestrians in the dark, such as at night or while in a tunnel
• Pedestrians whose clothing appears to be nearly the same color or
brightness as their surroundings
• Pedestrians near walls, fences, guardrails, or large objects
• Pedestrians who are on a metal object (manhole cover, steel plate, etc.)
on the road
• Pedestrians who are walking fast
• Pedestrians who are changing speed abruptly
• Pedestrians running out from behind a vehicle or a large object
• Pedestrians who are extremely close to the side of the vehicle (outside
rear view mirror, etc.)
*: Depending on the region in which the vehicle was sold, the pedestrian
detection function may not be available.

3274-5. Using the driving support systems
4
Driving
C-HR_OM_Europe_OM10528E
■ Conditions in which functions may not operate properly
In the following situations, the camera sensor may not detect white (yellow)
lines and various functions may not operate normally.
● There are shadows on the road that run parallel with, or cover, the white
(yellow) lines.
● The vehicle is driven in an area without white (yellow) lines, such as in front
of a tollgate or checkpoint, or at an intersection, etc.
● The white (yellow) lines are cracked, “Raised pavement marker” or stones
are present.
● The white (yellow) lines cannot be seen or are difficult to see due to sand,
etc.
● The vehicle is driven on a road surface that is wet due to rain, puddles, etc.
● The traffic lines are yellow (which may be more difficult to recognize than
lines that are white).
● The white (yellow) lines cross over a curb, etc.
● The vehicle is driven on a bright surface, such as concrete.
● The vehicle is driven on a surface that is bright due to reflected light, etc.
● The vehicle is driven in an area where the brightness changes suddenly,
such as at the entrances and exits of tunnels, etc.
● Light from the headlights of an oncoming vehicle, the sun, etc., enters the
camera.
● The vehicle is driven where the road diverges, merges, etc.
● The vehicle is driven on a slope.
● The vehicle is driven on a road which tilts left or right, or a winding road.
● The vehicle is driven on an unpaved or rough road.
● The vehicle is driven around a sharp curve.
● The traffic lane is excessively narrow or wide.
● The vehicle is extremely tilted due to carrying heavy luggage or having
improper tire pressure.
● The distance to the preceding vehicle is extremely short.
● The vehicle is moving up and down a large amount due to road conditions
during driving (poor r oads or road seams).
● The headlight lenses are dirty and emit a faint amount of light at night, or the
beam axis has deviated.
● The vehicle is struck by a crosswind.
● The vehicle has just changed lanes or crossed an intersection.
● Snow tires, etc., are equipped.

4594-5. Using the driving support systems
4
Driving
C-HR_OM_Europe_OM10528E
WARNING
●The system may not be able position the vehicle in the set location in the
following situations.
• The tires are extremely worn or the tire pressure is low
• The vehicle is carrying very heavy load
• The vehicle is tilted due to having luggage, etc., located on one side of
the vehicle
• There are road heaters installed in the parking lot to prevent the road
surface from freezing.
In any other situations when the set position and vehicle position greatly
differ, have the vehicle inspected by any authorized Toyota retailer or
Toyota authorized repairer, or any reliable repairer.
● Make sure to observe the following precautions regarding the exit parallel
parking assist mode.
Exit parallel parking assist mode is a function used when departing from a
parallel parking spot. However, this function may not be usable if obsta-
cles or people are detected in front of the vehicle. Only use this function
when departing from a parallel parking s pot. In the event that the steering
control operates, either turn the system off using the S-IPA switch or oper-
ate the steering wheel to stop the control.
● If exit parallel parking assist mode is mistakenly used in the following situ-
ations, the vehicle may make contact with an obstacle.
The departure function is operated in a direction where an obstacle is
present, but the obstacle is not detected by the side sensors (situations
such as when the vehicle is directly beside a pole).
● Observe the following precautions, as the sensors may stop functioning
properly which may lead to an accident.
• Do not subject the sensor to strong shocks by hitting it, etc. The sen-
sors may not function properly.
• When using a high-pressure washer to wash the vehicle, do not spray
water directly on the sensors. Equipment may not function properly if
subjected to an impact from strong water pressure. If the vehicle
bumper strikes something, equipment may not operate properly due to
a sensor malfunction. Have the vehicle inspected at any authorized
Toyota retailer or Toyota authoriz ed repairer, or any reliable repairer.