STARTER RELAY TOYOTA CAMRY 1994 XV10 / 4.G Wiring Diagrams User Guide

74
STARTING AND IGNITION (5S±FE)
I12 IGNITION SW
4±7 : CLOSED WITH IGNITION SW AT ST POSITION
10±9 : CLOSED WITH IGNITION SW AT ON OR ST POSITION
C 7 CLUTCH START SW (M/T)
1±2 : CLOSED WITH CLUTCH PEDAL FULLY DEPRESSED
STARTER RELAY
(6) 2± (6) 4 : CLOSED WITH CLUTCH START SW ON AND IGNITION SW AT ST POSITION (M/T)
CLOSED WITH IGNITION SW AT ST POSITION (A/T)
STARTER
POINTS CLOSED WITH CLUTCH START SW ON AND IGNITION SW AT ST POSITION
P 1 PARK/NEUTRAL POSITION SW (NEUTRAL START SW) (A/T)
2±3 : CLOSED WITH A/T SHIFT LEVER IN P OR N POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C 732E11B32I1233
D 130F10A30P 131
D2A30F16B30S 3A31D 2B30I 231S 4B31
E 7A32I 331
: RELAY BLOCKS
CODESEE PAGERELAY BLOCKS (RELAY BLOCK LOCATION)
125R/B NO. 1 (LEFT KICK PANEL)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A
1C
1E20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1G
20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M
2C22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2F22COWL WIRE AND J/B NO 2 (ENGINE COMPARTMENT LEFT)2G22COWL WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2H22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3B
3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
3D
24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
EF138 (1MZ±FE)EF140 (5S±FE)ENGINE WIRE AND COWL WIRE
IP144
ENGINE WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EC38 (1MZ±FE)INTAKE MANIFOLD RHEC40 (5S±FE)INTAKE MANIFOLD RH
IG42INSTRUMENT PANEL BRACE LH
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E1640 (5S FE)ENGINE WIREE2040 (5S±FE)ENGINE WIRE
E1940 (5S±FE)ENGINE WIRE
SERVICE HINTS

78
ENGINE CONTROL (1MZ±FE)
THIS SYSTEM UTILIZES AN ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU) AND
MAINTAINS OVERALL CONTROL OF THE ENGINE, TRANSMISSION AND SO ON. AN OUTLINE OF THE ENGINE CONTROL IS
EXPLAINED HERE.
1. INPUT SIGNALS
(1) ENGINE COOLANT TEMP. (WATER TEMP.) SIGNAL CIRCUIT
THE ENGINE COOLANT TEMP. SENSOR (WATER TEMP. SENSOR) DETECTS THE ENGINE COOLANT TEMP. AND HAS A
BUILT±IN THERMISTOR WITH A RESISTANCE WHICH VARIES ACCORDING TO THE WATER TEMP. IS INPUT INTO TERMINAL
THW OF ENGINE CONTROL MODULE (ECU) AS A CONTROL SIGNAL.
(2) INTAKE AIR TEMP. SIGNAL CIRCUIT
THE INTAKE AIR TEMP. SENSOR IS INSTALLED IN THE MASS AIR FLOW (AIR FLOW METER) AND DETECTS THE INTAKE AIR
TEMP., WHICH IS INPUT AS A CONTROL SIGNAL TO TERMINAL THA OF ENGINE CONTROL MODULE (ECU).
(3) OXYGEN SENSOR SIGNAL SYSTEM
THE OXYGEN DENSITY IN THE EXHAUST GASES IS DETECTED AND INPUT AS A CONTROL SIGNAL TO TERMINAL OXL, OXR
AND OXS OF THE ENGINE CONTROL MODULE (ECU). TO MAINTAIN STABLE DETECTION PERFORMANCE BY THE OXYGEN
SENSOR, A HEATER IS USED FOR WARMING THE SENSOR. THE HEATER IS ALSO CONTROLLED BY THE ENGINE CONTROL
MODULE (ECU) (HTL, HTR AND HTS).
(4) RPM SIGNAL SYSTEM
CAMSHAFT POSITION AND CRANKSHAFT POSITION ARE DETECTED BY THE CAMSHAFT POSITION SENSOR AND
CRANKSHAFT POSITION SENSOR. CRANKSHAFT POSITION IS INPUT AS A CONTROL SIGNAL TO TERMINAL G22+ OF THE
ENGINE CONTROL MODULE (ECU), AND ENGINE RPM IS INPUT TO TERMINAL NE+.
(5) THROTTLE SIGNAL CIRCUIT
THE THROTTLE POSITION SENSOR DETECTS THE THROTTLE VALVE OPENING ANGLE AS A CONTROL SIGNAL, WHICH IS
INPUT INTO TERMINAL VTA OF THE ENGINE CONTROL MODULE (ECU). WHEN THE VALVE IS COMPLETELY CLOSED, THE
CONTROL SIGNAL IS INPUT INTO TERMINAL IDL.
(6) VEHICLE SPEED SIGNAL SYSTEM
THE VEHICLE SPEED SENSOR (SPEED SENSOR), INSTALLED INSIDE THE COMBINATION METER, DETECTS THE VEHICLE
SPEED AND INPUTS A CONTROL SIGNAL TO TERMINAL SP1 OF THE ENGINE CONTROL MODULE (ECU).
(7) PARK/NEUTRAL POSITION SW (NEUTRAL START SW) SIGNAL SYSTEM
THE PARK/NEUTRAL POSITION SW (NEUTRAL START SW) DETECTS WHETHER THE SHIFT POSITION IS IN NEUTRAL OR
PARKING OR NOT, AND INPUTS A CONTROL SIGNAL TO TERMINAL NSW OF THE ENGINE CONTROL MODULE (ECU).
(8) A/C SW SIGNAL SYSTEM
THE A/C AMPLIFIER INPUTS THE A/C OPERATIONS TO TEMRINAL A/C OF THE ENGINE CONTROL MODULE (ECU) AS A
CONTROL SIGNAL.
(9) BATTERY SIGNAL CIRCUIT
VOLTAGE IS CONSTANTLY APPLIED TO TERMINAL BATT OF THE ENGINE CONTROL MODULE (ECU). WHEN THE IGNITION SW
TURNED ON, VOLTAGE FOR ENGINE CONTROL MODULE (ECU) START±UP POWER SUPPLY IS APPLIED TO TERMINALS +B
AND +B1 OF ENGINE CONTROL MODULE (ECU) VIA EFI MAIN RELAY.
(10) INTAKE AIR VOLUME SIGNAL CIRCUIT
INTAKE AIR VOLUME IS DETECTED BY THE MASS AIR FLOW (AIR FLOW METER) AND THE SIGNAL IS INPUT TO TERMINAL VG
OF THE ENGINE CONTROL MODULE (ECU). AS A CONTROL SIGNAL.
(11) STA SIGNAL CIRCUIT
TO CONFIRM WHETHER THE ENGINE IS CRANKING, THE VOLTAGE APPLIED TO THE STARTER MOTOR DURING CRANKING IS
DETECTED AND THE SIGNAL IS INPUT INTO TERMINAL STA OF THE ENGINE CONTROL MODULE (ECU) AS A CONTROL
SIGNAL.
(12) ENGINE KNOCK SIGNAL CIRCUIT
ENGINE KNOCKING IS DETECTED BY THE KNOCK SENSOR NO. 1 AND NO. 2 AND THE SIGNALS ARE INPUT INTO TERMINALS
KNKR AND KNKL AS A CONTROL SIGNAL.
SYSTEM OUTLINE

80
ENGINE CONTROL (1MZ±FE)
AM1
AM2 104
7
9 ST1
IG2
2G 1
IG 1 2
1 2
1 2
1 2
1 2
1 2 I20
E12 I18 E12 I18
BX1 4IJ1 16 EF1 3IP1 9IP1 16
IP3 15 66
666 641 32 2H 2
L±B
G±R
Y
R
L
GR
G
W B±OL±B B±W
B±WB±O
B±O B±O B±O
BB±O
BWW
BW
W±R
B±O
B±O B±O B±O
B±O
B±O
B±O
B±O
B±O Y RL GRG W
W±B W±B W±B
L±B L±BG±R
L±BB± O
B±W
B±W
BATTERY FL MAIN
2. 0LI18
B±O B±O 100A ALT
10A
STARTER
30A
AM2
FUSE BOX
IGNITION SW
CIRCUIT
OPENING
RELAY
INJECTOR NO. 1
INJECTOR NO. 6
INJECTOR NO. 3
INJECTOR NO. 4
INJECTOR NO. 5
INJECTOR NO. 2 I4
I9
I6
I7
I8
I5
I12
L±B
A 1
B 1B F10 , F16A
FROM POWER SOURCE
SYSTEM(
SEE PAGE 64)
1 B±O
B±W B±W
B±O
IP14
B±O 4
1G 9
1E 140A
AM1 2
1
1G 8
1A 67. 5A
IGN 1D 9
3B 20
3D 23C 2
3A 13
1C 113C 18
1M 1

84
ENGINE CONTROL (1MZ±FE)
CIRCUIT OPENING RELAY2±1 : CLOSED WITH STARTER RUNNING OR MEASURING PLATE (VOLUME AIR FLOW (AIR FLOW METER)) OPEN
EFI MAIN RELAY2±4 : CLOSED WITH IGNITION SW AT ON OR ST POSITION
E 4
ENGINE COOLANT TEMP. SENSOR (EFI WATER TEMP. SENSOR) 1±2 : 10.0 ± 20.0 K (±20°C, ±4°F)
: 4.0 ± 7.0 K (0°C, 32°F)
: 2.0 ± 3.0 K (20°C, 68°F)
: 0.9 ± 1.3 K (40°C, 104°F)
: 0.4 ± 0.7 K (60°C, 140°F)
: 0.2 ± 0.4 K (80°C, 176°F)
E 7(A), E 8(B), E 9(C), E10(D)
ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED
TRANSMISSION ECU)
VOLTAGE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTOR
BATT ± E1: ALWAYS 9.0±14.0 VOLTS
+B ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
+B1 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
IDL ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY OPEN)
0±3.0 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY CLOSED)
VC ± E1: ALWAYS 4.5±5.5 VOLTS (IGNITION SW AT ON POSITION)
VTA ± E1:0.3±0.8 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY CLOSED)
3.2±4.9 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY OPEN)
VG ± E1:4.0±5.5 VOLTS (IGNITION SW AT ON POSITION)
THA ± E1:0.5±3.4 VOLTS (IGNITION SW ON AND INTAKE AIR TEMP. 20°C, 68°F)
THW ± E1:0.2±1.0 VOLTS (ENGINE IDLING AND COOLANT TEMP. 80°C, 176°F)
#10, #20, #30, #40, #50, #60
± E01:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
PULSE GENERATION (ENGINE IDLING)
IGT1, IGT2, IGT3
IGT4, IGT5, IGT6 ± E1: PULSE GENERATION (ENGINE IDLING)
IGF ± E1:4.5±5.5 VOLTS (IGNITION SW AT ON POSITION)
PULSE GENERATION (ENGINE IDLING)
G22+ ± G±: PULSE GENERATION (ENGINE IDLING)
NE+ ± G±: PULSE GENERATION (ENGINE IDLING)
RSC, RSO ± E1: PULSE GENERATION (ENGINE IDLING AND A/C OPERATION)
OXS, OXL, OXR ± E1: PULSE GENERATION (MAINTAIN ENGINE SPEED AT 2500 RPM FOR TWO MINUTES AFTER WARMING UP)
HTS, HTL, HTR ± E01:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
0±3.0 VOLTS (ENGINE IDLING)
KNKL, KNLR ± E1: PULSE GENERATION (ENGINE IDLING)
NSW ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND OTHER SHIFT POSITION IN P OR N POSITION)
BELOW 3.0 VOLTS (IGNITION SW ON AND SHIFT POSITION IN P OR N POSITION)
SP1 ± E1: PULSE GENERATION (IGNITION SW ON AND ROTATE DRIVING WHEEL SLOWLY)
TE1 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
TE2 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
W ± E1: BELOW 3.0 VOLTS (MULFUNCTION INDICATOR LAMP ON)
9.0±14.0 VOLTS (MULFUNCTION INDICATOR LAMP OFF AND ENGINE RUNNING)
A/C ± E1: BELOW 1.5 VOLTS (ENGINE IDLING AND A/C SW ON)
7.5±14.0 VOLTS (A/C SW OFF)
ACT ± E1:9.0±14.0 VOLTS (ENGINE IDLING AND A/C SW ON)
BELOW 1.5 VOLTS (A/C SW OFF)
ACIS ± E01:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
STA ± E1:6.0 VOLTS OR MORE (ENGINE CRANKING)
I 4, I 5, I 6, I 7, I 8, I 9
INJECTOR1±2 : APPROX. 13.8 
T 1
THROTTLE POSITION SENSOR3±1 :0.2±5.7 KWITH CLEARANCE BETWEEN LEVER AND STOP SCREW 0 MM (0 IN.)
2±1 : LESS THAN 2.3 KWITH CLEARANCE BETWEEN LEVER AND STOP SCREW 0.5 MM (0.020 IN.)
WITH CLEARANCE BETWEEN LEVER AND STOP SCREW 0.7 MM (0.0276 IN.)
3±1 :2.0±10.2 KWITH THROTTLE VALVE FULLY OPEN
SERVICE HINTS

88
ENGINE CONTROL (5S±FE)
THIS SYSTEM UTILIZES AN ENGINE CONTROL MODULE (ENGINE ECU (M/T), ENGINE AND ELECTRONIC CONTROLLED
TRANSMISSION ECU (A/T)) AND MAINTAINS OVERALL CONTROL OF THE ENGINE, TRANSMISSION AND SO ON. AN OUTLINE OF THE
ENGINE CONTROL IS EXPLAINED HERE.
1. INPUT SIGNALS
(1) ENGINE COOLANT TEMP. (WATER TEMP.) SIGNAL SYSTEM
THE ENGINE COOLANT TEMP. SENSOR (EFI WATER TEMP. SENSOR) DETECTS THE ENGINE COOLANT TEMP. AND HAS A
BUILT±IN THERMISTOR WITH A RESISTANCE WHICH VARIES ACCORDING TO THE ENGINE COOLANT TEMP. (WATER TEMP.)
THUS THE ENGINE COOLANT TEMP. (WATER TEMP.) IS INPUT IN THE FORM OF A CONTROL SIGNAL TO TERMINAL THW OF
THE ENGINE CONTROL MODULE (ECU).
(2) INTAKE AIR TEMP. SIGNAL SYSTEM
THE INTAKE AIR TEMP. SENSOR (IN±AIR TEMP. SENSOR) IS DETECTS THE INTAKE AIR TEMP., WHICH IS INPUT AS A
CONTROL SIGNAL TO TERMINAL THA OF THE ENGINE CONTROL MODULE (ECU).
(3) OXYGEN SENSOR SIGNAL SYSTEM
THE OXYGEN DENSITY IN THE EXHAUST GASES IS DETECTED AND INPUT AS A CONTROL SIGNAL TO TERMINAL OX1 AND
OX2 OF THE ENGINE CONTROL MODULE (ECU).
(4) RPM SIGNAL SYSTEM
CRANKSHAFT POSITION AND ENGINE RPM ARE DETECTED BY THE PICK±UP COIL INSTALLED INSIDE THE DISTRIBUTOR.
CRANKSHAFT POSITION IS INPUT AS A CONTROL SIGNAL TO TERMINALS G+ AND G2 (CALIFORNIA), OF THE ENGINE
CONTROL MODULE (ECU), AND RPM IS INPUT TO TERMINAL NE+.
(5) THROTTLE SIGNAL SYSTEM
THE THROTTLE POSITION SENSOR DETECTS THE THROTTLE VALVE OPENING ANGLE, WHICH IS INPUT AS A CONTROL
SIGNAL TO TERMINAL VTA OF THE ENGINE CONTROL MODULE (ECU), OR WHEN THE VALVE IS FULLY CLOSED, TO
TERMINAL IDL
(6) VEHICLE SPEED SIGNAL SYSTEM
THE VEHICLE SPEED SENSOR (SPEED SENSOR), INSTALLED INSIDE THE COMBINATION METER, DETECTS THE VEHICLE
SPEED AND INPUTS A CONTROL SIGNAL TO TERMINAL SPD OF THE ENGINE CONTROL MODULE (ECU).
(7) PARK/NEUTRAL POSITION SW (NEUTRAL START SW) SIGNAL SYSTEM (A/T)
THE PARK/NEUTRAL POSITION SW (NEUTRAL START SW) DETECTS WHETHER THE SHIFT POSITION ARE IN NEUTRAL AND
PARKING OR NOT, AND INPUTS A CONTROL SIGNAL TO TERMINAL NSW OF THE ENGINE CONTROL MODULE (ECU).
(8) A/C SW SIGNAL SYSTEM
THE A/C AMPLIFIER INPUTS THE A/C OPERATIONS TO TARMINAL ACA OF THE ENGINE CONTROL MODULE (ECU) AS A
CONTROL SIGNAL.
(9) BATTERY SIGNAL CIRCUIT
VOLTAGE IS CONSTANTLY APPLIED TO TERMINAL BATT OF THE ENGINE CONTROL MODULE (ECU). WHEN THE IGNITION SW
TURNED ON, THE VOLTAGE FOR ENGINE CONTROL MODULE (ECU) START±UP POWER SUPPLY IS APPLIED TO TERMINALS
+B AND +B1 OF ENGINE CONTROL MODULE (ECU) VIA EFI MAIN RELAY. THE CURRENT FLOWING THROUGH THE IGN FUSE
FLOWS TO TERMINAL IGSW OF THE ENGINE CONTROL MODULE (ECU).
(10) INTAKE AIR VOLUME SIGNAL SYSTEM
INTAKE AIR VOLUME IS DETECTED BY THE MANIFOLD ABSOLUTE PRESSURE SENSOR (VACUUM SENSOR) (FOR MANIFOLD
PRESSURE) AND IS INPUT AS A CONTROL SIGNAL TO TERMINAL PIM OF THE ENGINE CONTROL MODULE (ECU).
(11) STA SIGNAL CIRCUIT
TO CONFIRM WHETHER THE ENGINE IS CRANKING, THE VOLTAGE APPLIED TO THE STARTER MOTOR DURING CRANKING IS
DETECTED AND THE SIGNAL IS INPUT INTO TERMINAL STA OF THE ENGINE CONTROL MODULE (ECU) AS A CONTROL
SIGNAL.
(12) ENGINE KNOCK SIGNAL CIRCUIT
ENGINE KNOCKING IS DETECTED BY KNOCK SENSOR AND THE SIGNAL IS INPUT INTO TERMINAL KNK AS A CONTROL
SIGNAL.
(13) ELECTRICAL LOAD SIGNAL SYSTEM
THE SIGNAL WHEN SYSTEMS SUCH AS THE REAR WINDOW DEFOGGER, HEADLIGHTS, ETC. WHICH CAUSE A HIGH
ELECTRICAL BURDEN ARE ON IS INPUT TO TERMINAL ELS AS A CONTROL SIGNAL.
SYSTEM OUTLINE

93
* 1 : CALIFORNIA
*
2 : EX. CALIFORNIA
* 3 : EX. CALIFORNIA M/T
*
5 : EX.*
4 *
4 : FOR CANADA IN TMM MADE
CB
17 8 9 13 4 15
146 212 1
23 IP119
IP115
IP313
IP11
IP3196 61
666
M
5 4
E17I18 I18 I18
I18
I18I18 I18 I18 I18
IP3 15IP1 4
BX1 4IJ 1 16
BX1 5
BL IG 2 1
EC B 7B15 B14 B8A11
A
14 B5B6A143
BR±B
GR
G±W
R±W B±O
B±W B±WB±O L±B
G±R
W±B W±B W±BW±B W±B L±B L±BBRR±W G±WGR BR±B
L±BBR R±LW
B±O W
R±L
BRR±LBR BR BR BR
W
G±R
L±B
W±R
B±O
B±O
G±R
BR±B
Y±G
G±W
R±W
(
SHIELDED)G±RL±B
R±LW
BR BR±B
GR
G±W
R±WTT TE1 TE2 VF1 OX1 OX2 E1
B±O B±W
B±W
(
SHIELDED) BR (
SHIELDED) (
SHIELDED) (
SHIELDED)
W±R
D1
E1 OX2 OX1 FCTT TE1 TE2 VF STAW+B FP
E7 ,E8 ,E10
N1
F15
O3FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
10A
STARTER
DATA LINK CONNECTOR 1
(
CHE CK CONNE CTOR)
CIRCUIT
OPENING
RELAY
NOISE FILTER
(
FOR IGNITION SYSTEM)
OXYGEN SENSOR(
MAIN)FUEL
PUMP ENGINE CONTROL MODULE(
ENGINE AND ELECTRONIC
CONTROLLED TRANSMISSION ECU)(
A/T)
C
E16 BR1 B
BR BRBR 19
IG±
BR BR
IP316
BR
BR
ED4
I18
BR(
SHIELDED) (
*3)(
*3)
(
*3) (
*3)
B E11 , E12CA,E14
ENGINE CONTROL MODULE(
ENGINE ECU)(
M/T)
3D 2
3C 2
3B20
3A 13
1C 113C 18
1M 1

101
* 2 : TMM MADE *
1:TMCMADE
AB
8913 415
146 212 1
23 IP313
IP11
IP3196 62C A6
666
M
5 4 I18
I18I18 I18 I18
IP3 15IP1 4
BX1 4IJ1 16IP3 18
BX1 5
BL IG 2 1
ECB 15 B7B8A2
C
B 1B6C43
GR
G±W
R±W B±O
B±W B±W B±WB±O L±B
G±R
W±B W±B W±BW±B W±B L±B L±BBRR±W G±WGR
L±BBR R±LW
B±O W BRR±L
W
G±R
L±B
W±R
B±O
B±O
G±R
Y±G
G±W
R±W
(
SHIELDED)G±RL±B
R±LW
BR
BR GR
G±W
R±WTE1 TE2 VF1 OX1 OX2 E1
B±O B±W
W±RD1
OX2 OX1 FCTE1 TE2 VF STAWB FP
E11 , E12 , E14
N1
F15
O3
O2FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
10A
STARTER
DATA LINK CONNECTOR 1
(
CHECK CONNECTOR)
CIRCUIT
OPENING
RELAY
NOISE FILTER
(
FOR I GNITI ON
SYSTEM)
OXYGEN SENSOR
(
SUB)OXYGEN SENSOR
(
MAIN)FUEL
PUMP ENGINE CONTROL MODULE(
ENGINE ECU) IG± 19 B
BR(
SHIELDED) IP119
ED 2 11 IP316
BR BR(
SHIELDED)
(
SHIELDED)
R±L
BR BR
BR
BR
B±W
(
*2)(
*1)
B±W
E17
3C 2
3D 23B
3A 13
3C 18
1C 11
1M 1

192
CRUISE CONTROL
B
ST1 IG1 ACC
AM1
7
IP3 8IP3 11
II1 4 2 1
1 1 213 41883
17 15
20 1420 510 2
13B 4 B 12 B5B9 A 6
1 2
IG CC
I13
11 R±L R±L
R±L
W±B
W±B W±B
B±R B±W
R±L B±W
B±R B
B
W±B
W±L
W
LG±R
R±W LG±R
R±W LG±R
R±W
R±WW±B
W±B
G±BG
V±Y
G±Y V±YP LG B
FROM POWER SOURCE SYSTEM(
SEEPAGE64)
10A
GAUGE
COMBINATON METER
DIODE
(
FOR CRUISE
CONTROL)VEHICLE
SPEED SENSOR
(
SPEED SENSOR)
DATA LINK CONNECTOR 2
(
TDCL)
A/D JUNCTION
CONNECTOR
CRUISE CONTROL
CLUTCH SW
(
M/T)
CRUISE CONTROL SW
[COMB. SW]
DA TA LINK CONNE CTOR 1
(
CHECK CONNECTOR)
PARKING
BRAKE SW
PARKING
BRAKE SWMAIN
CA NCELSET/
COAST RE SUME/
ACCEL N&C GND CMS CCS TC PKBBSPD PI
TC
IGNITION SW
P
N5
6EF1 1
B±W B±W
J1
P1
D5
C8 , C9
D3
V5A
PARK/NEUTRAL POSITION SW
(
NE UTRAL S TA RT SW)
(
A/T) B
TO STARTER RELAY
CRUIS E CONTROL ECU C16
C15
C13
D1
P3
P2
(
1MZ±FE)
SPEED
CRUISEI12
IP3 2
(
A/T)
(
5S±FE)IP3 14
(
A/T)
(
M/T) (
M/T)
R±L
TO BA CK ±UP LIGHT SW(
M/T)
TO PARK/NEUTRAL POSITION SW
(
NE UTRA L S TA RT SW)(
A/T)
TO GENERATOR(
ALTERNATOR)
R±L
I18
(
*2) O
(
*1)
G±L
(
*2) O
(
*1)
O
(
*1) G±L
(
*2)
1G 63C16
1A 14 3B16 1E 5
1A 71D61B6 15A
ECU±IG
3D 22 3B8
3B 10 3B19 3B9
3B 73B18
3B 17
3B 14 3B5
3C 18
1M1
1C11
3B 12
3D 83C83B 15
3D 16

237
*
1 : W/O A/T INDICATOR LIGHT
* 2 : W/ A/T INDICATOR LIGHT
*
3 : MALFUNCTION INDICATOR LAMP
(
CHECK ENGINE WARNING LIGHT)
*7 : 5S±FE *
6 : 1MZ±FE * 5 : TMM MADE
*
4:TMCMADE
AB
C
COMBINATION METER1
IEIF 2 1B 15 B3B9B13
B 12B 8B14 C 1 C 3 A 9A 10C 2
II1 4
11B DE 18 A
FB E D
8 A
FAFROM POWER SOURCE SYSTEM(
SEE PAGE 64)
B±W
R±Y
R±GW±R Y±G B±W
B±O G± L
G±R
R±Y R±Y W±BG±RG± L
±B W±B
R±W R±W
R±W
G±O
Y
B±Y
R±BB±YY G±O R±Y
R±Y
R±W 10A
STARTER
TO LIGHT FAILURE
SENSOR
FROM º HEAD RHº FUSE
FROM º HEAD(
UP R±RH)
ºFUSE
(
CA NADA) (
USA) CRUISE
(
*3)
BRAKE
BULB
CHECK
RE AR LIGHT
O/D OFF
CHARGE
SRS
HIGH BEAM
PKB BRK
TOO/DMAINSW
TO GENERATOR(
ALTERNATOR)
TO CENTER AIRBAG
SENSOR ASSEMBLY
TO DIMMER SW
[COMB. SW] TO CRUISE CONTROL ECU
TO E NGINE CONTROL MODULE
(
ENGINE AND ELECTRONIC CONTROLLED
TRANSMISSION ECU)(
A/T)
TO E NGINE CONTROL MODULE
(
ENGINE ECU)(
M/T)
BRAKE FLUID
LEVEL SWJUNCTION
CONNECTOR
JUNCTION
CONNE CTOR
DAYTIME RUNNING
LIGHT RELAY
(
MAIN) PARKING
BRAKE SW
PARKING
BRAKE SW(
EX. 1MZ±FE A/T)
(
1MZ±FE A/T)
JUNCTION
CONNECTOR
JUNCTION
CONNECTOR (
USA)
(
CANA DA) C8 ,C9 , C10
J2
J2 B2
P3
P2 D4
J2
J3(
*1) (
*1)
(
USA)
II1 2
I6
G±O
G±O G±O
(
*2) FROM A/T
INDICATOR LIGHT
W±B
(
CA NADA)(
*5) (
*5)
O
(
*4)O
(
*4)
4
3B 203C 2
1D 31F3 7. 5A
IGN7. 5A
SRS
3B 19 3D19 3B 83D18
3D 83C8 3A 10
1M 51C 8
W

256
GROUND POINT*3 :W/POWERWINDOW *
2:TMMMADE * 1 : TMC MADE
* 6 : AIR CONDITIONING(
LEVER CONTROL SW TYPE) *
5 : AIR CONDITIONING(
PUSH CONTROL SW TYPE) * 4 : W/O POWER WINDOW
LIGHT CONTROL SW
[COMB. SW]
KEY INTERLOCK
SOLENOID
WIPER AND WASHER SW
[COMB. SW]
RE AR WINDOW
DEFOGGER SW
CLOCK
CIGARETTE LIGHTER
BRAKE FLUID LEVEL
SW
TURN SIGNAL FLASHER
MOON ROOF
CONTROL RELAY
MOON ROOF MOTOR
MOON ROOF LIMIT SW
RADIO AND PLAYER
STEREO COMPONENT
AMPLIFIERBLOWER RESISTOR
A/C AMPLIFIER HEATER CONTROL SW
(
PUSH CONTROL SW
TYPE)
OR AIR VENT
MODE CONTROL SW
(
LEVER CONTROL SW
TYPE) BLOWER SW
STARTER RELAY
COMBINATION METER
CIRCUIT OPENING
RELAY
DAYTIME RUNNING
LIGHT RELAY(
MAIN)
CRUISE CONTROL ECU
CRUISE CONTROL SW
[COMB. SW]
HEATER RELAY I7
I7
I7
I7
I7
I13I13 I13 I13 I12
IH IG II2F
4 1
IM27F FI5
I5 W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
BR
BR BRW±B W±BW±B
W±B
W±B W±BW±B
W±B
W±B
W±B
W±B
W±B W±B
W±B
W±B W±B
W±B W±B
W±B W±BW±BW±B W±B W±B W±B
W±B
W±BW±B
W±B
VANI TY LIGHT LHAIR VENT MODE CONTROL
SERVO MOTOR
W±B
W±B W±B W±B JUNCTION
CONNE CTOR J1
DIMMER SW
[COMB. SW]
IL17 IK 14
W±B
W±B
CENTER AIRBAG SENSOR
ASSEMBLY(
E2)6
VANITY LIGHT RHW±B W±B
W±B
W±B
MOON ROOF CONTROL SW
AND PERSONAL LI GHT
(
W/ CD PL AYER)(
CANADA)
(
W/O CD PLAYER)IE
W±BIV 2 IV1
(
W/G)(
S /D, C/P) (
*1)W±B W±B
(
*2)
(
*2)
B5:S/D
B21 : C/P
B32 : W/G
B4:S/D
B21 : C/P
B31 : W/G
BK : S/D, C/P
BP : W/G
6 6 W±B
I5
W±B
DA TA LINK
CONNE CTOR 3
F W±B
B4:S/D
B30 : W/G
B20 : C/PI7:*5
I14 : * 6
1 HIGH BEAM INDICATOR
LIGHT [COMB. METER]
CRUISE CONTROL
CLUCH SW W±B
NOISE FILTER
POWER MAIN RELAY
INTEGRATION RELAY
UNLOCK WARNING SW
[IGNITION SW] 1C11
W±B W±B
CENTER AIRBAG SENSOR
ASSEMBLY(
E1)
1G4
1F1
1M1
1I6 1F2
1M 51C 8
3C
3D6
3A13
3A12
3B5
3C 186
3B14DEFOGGER RELAY 1C10