length TOYOTA CAMRY 1994 XV10 / 4.G Wiring Diagrams Workshop Manual

79
2. CONTROL SYSTEM
*SFI (SEQUENTIAL MULTIPORT FUEL INJECTION) (EFI (ELECTRONIC FUEL INJECTION) SYSTEM
THE EFI SYSTEM MONITORS THE ENGINE CONDITION THROUGH THE SIGNALS INPUT FROM EACH SENSOR (INPUT SIGNALS
FROM (1) TO (12) ETC.). THE BEST FUEL INJECTION VOLUME IS DECIDED BASED ON THIS DATA AND THE PROGRAM MEMORIZED
BY THE ENGINE CONTROL MODULE (ECU), AND THE CONTROL SIGNAL IS OUTPUT TO TERMINALS #10, #20, #30, #40, #50 AND #60
OF THE ENGINE CONTROL MODULE (ECU) TO OPERATE THE INJECTOR (INJECT THE FUEL). THE EFI SYSTEM PRODUCES
CONTROL OF FUEL INJECTION OPERATION BY THE ENGINE CONTROL MODULE (ECU) IN RESPONSE TO THE DRIVING
CONDITIONS.
*ESA (ELECTRONIC SPARK ADVANCE) SYSTEM
THE ESA SYSTEM MONITORS THE ENGINE CONDITION THROUGH THE SIGNALS INPUT TO THE ENGINE CONTROL MODULE (ECU)
FROM EACH SENSOR (INPUT SIGNALS FROM (1), (3), (4) TO (12) ETC.). THE BEST IGNITION TIMING IS DECIDED ACCORDING TO
THIS DATA AND THE MEMORIZED DATA IN THE ENGINE CONTROL MODULE (ECU) AND THE CONTROL SIGNAL IS OUTPUTS TO
TERMINALS IGT1, IGT2, IGT3, IGT4, IGT5 AND IGT6. THIS SIGNAL CONTROLS THE IGNITER TO PROVIDE THE BEST IGNITION
TIMING FOR THE DRIVING CONDITIONS.
*HEATED OXYGEN SENSOR (OXYGEN SENSOR) HEATER CONTROL SYSTEM
THE OXYGEN SENSOR HEATER CONTROL SYSTEM TURNS THE HEATER ON WHEN THE INTAKE AIR VOLUME IS LOW (TEMP. OF
EXHAUST EMISSIONS IS LOW), AND WARMS UP THE OXYGEN SENSOR (NO. 1 AND NO. 2) TO IMPROVE DETECTION
PERFORMANCE OF THE SENSOR.
THE ENGINE CONTROL MODULE (ECU) EVALUATES THE SIGNALS FROM EACH SENSOR (INPUT SIGNALS FROM (1), (4), (9) TO (10)
ETC.), AND OUTPUT CURRENT TO TERMINALS HTL, HTR AND HTS AND CONTROL THE HEATER.
*IAC (IDLE AIR CONTROL (ISC)) SYSTEM
THE IAC (ISC) SYSTEM (ROTARY SOLENOID TYPE) INCREASES THE RPM AND PROVIDES IDLE STABILITY FOR FAST IDLE±UP
WHEN THE ENGINE IS COLD, AND WHEN THE IDLE SPEED HAS DROPPED DUE TO ELECTRICAL LOAD AND SO ON, THE ENGINE
CONTROL MODULE (ECU) EVALUATES THE SIGNALS FROM EACH SENSOR (INPUT SIGNALS FROM (1), (4), (5), (8), (9) ETC.),
OUTPUTS CURRENT TO TERMINALS RSO AND RSC TO CONTROL IDLE AIR CONTROL VALVE.
*EGR CONTROL SYSTEM
THE EGR CONTROL SYSTEM DETECTS THE SIGNAL FROM EACH SENSOR (INPUT SIGNALS FROM (1), (4), (9), (10), ETC)., AND
OUTPUTS CURRENT TO TERMINAL EGR TO CONTROL THE EGR VALVE.
*ACIS (ACOUSTIC CONTROL INDUCTION SYSTEM)
ACIS INCLUDES A VALVE IN THE BULKHEAD SEPARATING THE SURGE TANK INTO TWO PARTS. THIS VALVE IS OPENED AND
CLOSED IN ACCORDANCE WITH THE DRIVING CONDITIONS TO CONTROL THE INTAKE MANIFOLD LENGTH IN TWO STAGES FOR
INCREASED ENGINE OUTPUT IN ALL RANGES FROM LOW TO HIGH SPEEDS.
THE ENGINE CONTROL MODULE (ECU) JUDGES THE ENGINE SPEED BY THE SIGNALS ((4), (5)) FROM EACH SENSOR AND
OUTPUTS SIGNALS TO THE TERMINAL ACIS TO CONTROL THE VSV (FOR OPENING AND CLOSING THE INTAKE CONTROL VALVE)
3. DIAGNOSIS SYSTEM
WITH THE DIAGNOSIS SYSTEM, WHEN THERE IS A MALFUNCTION IN THE ENGINE CONTROL MODULE (ECU) SIGNAL SYSTEM, THE
MALFUNCTIONING SYSTEM IS RECORDED IN THE MEMORY.
4. FAIL±SAFE SYSTEM
WHEN A MALFUNCTION HAS OCCURRED IN ANY SYSTEM, IF THERE IS A POSSIBILITY OF ENGINE TROUBLE BEING CAUSED BY
CONTINUED CONTROL BASED ON THE SIGNALS FROM THAT SYSTEM, THE FAIL±SAFE SYSTEM EITHER CONTROLS THE SYSTEM
BY USING DATA (STANDARD VALUES) RECORDED IN THE ENGINE CONTROL MODULE (ECU) MEMORY OR ELSE STOPS THE
ENGINE.