fuse TOYOTA CAMRY 1994 XV10 / 4.G Wiring Diagrams Owner's Guide

163
CURRENT ALWAYS FLOWS TO TERMINAL 8 OF THE DOOR LOCK CONTROL RELAY THROUGH THE POWER FUSE.
WHEN THE IGNITION SW IS TURNED ON, THE CURRENT FLOWING THROUGH THE GAUGE FUSE FLOWS THROUGH THE COIL SIDE
OF THE POWER MAIN RELAY TO GROUND, CAUSING THE RELAY TO OPERATE. THE CURRENT FLOWING THROUGH THE POWER
FUSE FLOWS TO THE LH DOOR LOCK CONTROL SW, CAUSING THE INDICATOR LIGHT TO LIGHT UP.
1. MANUAL LOCK OPERATION
WHEN THE DOOR LOCK CONTROL SW AND KEY SW ARE PUSHED TO LOCK POSITION, A LOCK SIGNAL IS INPUT TO TERMINAL 10,
12 OF THE DOOR LOCK CONTROL RELAY AND CAUSES THE RELAY TO FUNCTION. CURRENT FLOWS FROM TERMINAL 8 OF THE
RELAY " TERMINAL 4 " TERMINAL 4 OF THE DOOR LOCK MOTORS, (EX. C/P FRONT DOOR) OR TERMINAL 7 (C/P FRONT DOOR),
OF THE DOOR LOCK MOTOR TERMINAL 2 OF THE BACK DOOR LOCK MOTOR " TERMINAL 2 OF THE DOOR LOCK MOTORS, (EX.
C/P FRONT DOOR) OR TERMINAL 5 (C/P FRONT DOOR) OF THE DOOR LOCK MOTOR TERMINAL 1 OF THE BACK DOOR LOCK
MOTOR " TERMINAL 3 OF THE RELAY " TERMINAL 16 " TO GROUND AND THE DOOR LOCK MOTOR CAUSES THE DOOR TO
LOCK.
2. MANUAL UNLOCK OPERATION
WHEN THE DOOR LOCK CONTROL SW AND KEY SW RH TO UNLOCK POSITION, AN UNLOCK SIGNAL IS INPUT TO TERMINAL 11, 13
OF THE DOOR LOCK RELAY AND CAUSES THE RELAY TO FUNCTION. CURRENT FLOWS FROM TERMINAL 8 OF THE RELAY "
TERMINAL 3 " TERMINAL 2 OF THE DOOR LOCK MOTORS, (EX. C/P FRONT DOOR) OR TERMINAL 5 (C/P FRONT DOOR) OF THE
DOOR LOCK MOTOR TERMINAL 1 OF THE BACK DOOR LOCK MOTOR " TERMINAL 4 OF THE DOOR LOCK MOTORS, (EX. C/P
FRONT DOOR) OR TERMINAL 7 (C/P FRONT DOOR), OF THE DOOR LOCK MOTOR TERMINAL 2 OF THE BACK DOOR LOCK MOTOR "
TERMINAL 4 OF THE RELAY " TERMINAL 16 " TO GROUND AND DOOR LOCK MOTORS CAUSES DOOR TO UNLOCK.
3. DOUBLE OPERATION UNLOCK OPERATION
WHEN THE DOOR LOCK KEY SW (DRIVER'S) IS TURNED TO THE UNLOCK SIDE, ONLY THE DRIVER'S DOOR IS MECHANICALLY
UNLOCKED. TURNING THE DOOR LOCK KEY SW (DRIVER'S) TO THE UNLOCK SIDE CAUSES A SIGNAL TO BE INPUT TO TERMINAL 9
OF THE RELAY, AND IF THE SIGNAL IS INPUT AGAIN WITHIN 3 SECONDS BY TURNING THE SW TO THE UNLOCK SIDE AGAIN,
CURRENT FLOWS TERMINAL 3 " TERMINAL 2 OF DOOR LOCK MOTORS, (EX. C/P FRONT DOOR) OR TERMINAL 5 (C/P FRONT
DOOR) OF THE DOOR LOCK MOTOR TERMINAL 1 OF THE BACK DOOR LOCK MOTOR " TERMINAL 4 OF THE DOOR LOCK MOTORS,
(EX. C/P FRONT DOOR) OR TERMINAL 7 (C/P FRONT DOOR), OF THE DOOR LOCK MOTOR TERMINAL 2 OF THE BACK DOOR LOCK
MOTOR " TERMINAL 4 OF THE RELAY " TERMINAL 16 " GROUND, CAUSING THE DOOR LOCK MOTORS TO OPERATE AND
UNLOCK THE DOORS.
4. IGNITION KEY REMINDER OPERATION
*OPERATING DOOR LOCK KNOB (OPERATION OF DOOR LOCK MOTORS)
WITH IGNITION KEY IN CYLINDER (UNLOCK WARNING SW ON), WHEN THE DOOR IS OPENED AND LOCKED USING DOOR LOCK
KNOB (DOOR LOCK MOTOR), THE DOOR IS LOCKED ONCE BUT EACH DOOR IS UNLOCKED SOON BY THE FUNCTION OF RELAY.
AS A RESULT, THE CURRENT FLOWS FROM TERMINAL 8 OF THE RELAY " TERMINAL 3 " TERMINAL 2 OF THE DOOR LOCK
MOTORS, (EX. C/P FRONT DOOR) OR TERMINAL 5 (C/P FRONT DOOR) OF THE DOOR LOCK MOTOR TERMINAL 2 OF THE BACK
DOOR LOCK MOTOR " TERMINAL 4 OF THE DOOR LOCK MOTORS, (EX. C/P FRONT DOOR) OR TERMINAL 7 (C/P FRONT DOOR),
OF THE DOOR LOCK MOTOR TERMINAL 1 OF THE BACK DOOR LOCK MOTOR " TERMINAL 4 OF THE RELAY " TERMINAL 16 "
TO GROUND AND CAUSES ALL THE DOORS TO UNLOCK.
*OPERATING DOOR LOCK CONTROL SW OR DOOR LOCK KEY SW
WITH IGNITION KEY IN CYLINDER (UNLOCK WARNING SW ON), WHEN THE DOOR IS OPENED AND LOCKED USING DOOR LOCK
CONTROL SW OR KEY SW, THE DOOR IS LOCKED ONCE BUT EACH DOOR IS UNLOCK BY THE FUNCTION OF SW CONTAINED IN
MOTORS, WHICH THE SIGNAL IS INPUT TO TERMINAL 6 (DRIVER'S) OR 5 (PASSENGER'S) OF THE RELAY. ACCORDING TO THIS
INPUT SIGNAL, THE CURRENT IN ECU FLOWS FROM TERMINAL 8 OF THE RELAY " TERMINAL 3 " TERMINAL 2 OF THE DOOR
LOCK MOTORS, (EX. C/P FRONT DOOR) OR TERMINAL 5 (C/P FRONT DOOR) OF THE DOOR LOCK MOTOR TERMINAL 2 OF THE
BACK DOOR LOCK MOTOR " TERMINAL 4 OF THE DOOR LOCK MOTORS, TERMINAL 1 OF THE BACK DOOR LOCK MOTOR "
TERMINAL 4 OF THE RELAY " TERMINAL 16 " TO GROUND AND CAUSES ALL THE DOOR TO UNLOCK.
*IN CASE OF KEY LESS LOCK
WITH IGNITION KEY IN CYLINDER (UNLOCK WARNING SW ON), WHEN THE UNLOCK FUNCTION IS DISTURBED MORE THAN 0.2
SECONDS, FOR EXAMPLE PUSHING THE DOOR LOCK KNOB ETC., THE DOOR HOLDS ON LOCK CONDITION. CLOSING THE DOOR
AFTER, DOOR COURTESY SW INPUTS THE SIGNAL INTO TERMINAL 2 OR 14 OF THE RELAY. BY THIS INPUT SIGNAL, THE ECU
WORKS AND CURRENT FLOWS FROM TERMINAL 8 OF THE RELAY " TERMINAL 3 " TERMINAL 2 OF THE DOOR LOCK MOTORS,
(EX. C/P FRONT DOOR) OR TERMINAL 5 (C/P FRONT DOOR) OF THE DOOR LOCK MOTOR TERMINAL 1 OF THE BACK DOOR LOCK
MOTOR " TERMINAL 4 OF THE DOOR LOCK MOTORS, (EX. C/P FRONT DOOR) OR TERMINAL 7 (C/P FRONT DOOR), OF THE
DOOR LOCK MOTOR TERMINAL 2 OF THE BACK DOOR LOCK MOTOR " TERMINAL 4 OF THE RELAY " TERMINAL 16 " TO
GROUND AND CAUSES ALL THE DOORS TO UNLOCK.
SYSTEM OUTLINE

169
CURRENT IS APPLIED AT ALL TIMES THROUGH POWER FUSE TO TERMINAL 5 OF POWER MAIN RELAY AND ALSO THROUGH DOME
FUSE TO TERMINAL 12 OF MOON ROOF CONTROL RELAY.
WITH THE IGNITION SW TURNED ON, THE CURRENT FLOWS FROM TERMINAL 1 OF POWER MAIN RELAY " TERMINAL 2 " TO
GROUND THROUGH GAUGE FUSE. AS A RESULT, POWER MAIN RELAY IS ACTIVATED AND THE CURRENT TO TERMINAL 5 OF
POWER MAIN RELAY FLOWS FROM TERMINAL 3 OF RELAY TO TERMINAL 6 OF MOON ROOF CONTROL RELAY.
1. SLIDE OPEN OPERATION
WHEN THE IGNITION SW IS TURNED ON AND THE MOON ROOF CONTROL SW IS PUSHED TO THE OPEN POSITION, A SIGNAL IS
INPUT FROM TERMINAL 3 OF MOON ROOF CONTROL SW TO TERMINAL 1 OF MOON ROOF CONTROL RELAY. MOON ROOF LIMIT SW
NO. 2 ON AT THIS TIME.
WHEN THIS OCCURS, THE RELAY IS ACTIVATED AND THE CURRENT TO TERMINAL 6 OF MOON ROOF CONTROL RELAY FLOWS
FROM TERMINAL 5 " TERMINAL 1 OF MOON ROOF MOTOR " TERMINAL 3 " TERMINAL 4 OF MOON ROOF CONTROL RELAY "
TERMINAL 11 " TO GROUND AND ROTATES THE MOTOR TO OPEN THE MOON ROOF WHILE THE SW IS BEING PUSHED TO OPEN
POSITION.
2. SLIDE CLOSE OPERATION
WITH THE IGNITION SW TURNED ON, THE MOON ROOF COMPLETELY OPEN AND MOON ROOF LIMIT SW NO. 1 AND NO. 2 BOTH ON,
WHEN THE MOON ROOF CONTROL SW IS PUSHED TO THE CLOSE POSITION A SIGNAL IS INPUT FROM TERMINAL 6 OF MOON
ROOF CONTROL SW TO TERMINAL 2 OF MOON ROOF CONTROL RELAY.
WHEN THIS OCCURS, THE RELAY IS ACTIVATED AND THE CURRENT TO TERMINAL 6 OF MOON ROOF CONTROL RELAY FLOWS
FROM TERMINAL 4 " TERMINAL 3 OF MOON ROOF MOTOR " TERMINAL 1 " TERMINAL 5 OF MOON ROOF CONTROL RELAY "
TERMINAL 11 " TO GROUND AND ROTATES THE MOTOR TO CLOSE THE MOON ROOF WHILE THE SW IS BEING PUSHED TO CLOSE
POSITION.
MOON ROOF LIMIT SW NO. 1 TURNS OFF (LIMIT SW NO. 2 IS ON) AND A 100 MM BEFORE FULLY CLOSE POSITION, SIGNAL IS INPUT
FROM TERMINAL 1 OF LIMIT SW NO. 1 TO TERMINAL 8 OF MOON ROOF CONTROL RELAY. THIS SIGNAL ACTIVATES THE RELAY AND
STOPS CONTINUITY FROM TERMINAL 6 OF MOON ROOF CONTROL RELAY TO TERMINAL 11. AS A RESULT, THE MOON ROOF
STOPS AT THIS POSITION.
TO CLOSE THE MOON ROOF COMPLETELY, PUSHING THE MOON ROOF CONTROL SW AGAIN TO THE CLOSE SIDE CAUSES A
SIGNAL TO BE INPUT AGAIN TO TERMINAL 2 OF MOON ROOF CONTROL RELAY. THIS ACTIVATES THE RELAY AND THE MOON ROOF
WILL CLOSE AS LONG AS THE MOON ROOF CONTROL SW IS BEING PUSHED, ALLOWING THE MOON ROOF TO FULLY CLOSE.
3. TILT UP OPERATION
WHEN THE MOON ROOF CONTROL SW IS PUSHED TO TILT UP POSITION, WITH THE IGNITION SW TURNED ON AND THE MOON
ROOF COMPLETELY CLOSED (MOON ROOF LIMIT SW NO. 2 IS OFF), A SIGNAL IS INPUT FROM TERMINAL 5 OF MOON ROOF
CONTROL SW TO TERMINAL 3 OF MOON ROOF CONTROL RELAY. AS A RESULT, THE RELAY IS ACTIVATED AND THE CURRENT TO
TERMINAL 6 OF RELAY FLOWS FROM TERMINAL 4 OF RELAY " TERMINAL 3 OF MOON ROOF MOTOR " TERMINAL 1 " TERMINAL
5 OF RELAY " TERMINAL 11 TO GROUND AND ROTATES THE MOTOR SO THAT TILT UP OPERATION OCCURS AS LONG AS THE
MOON ROOF CONTROL SW IS PUSHED ON THE TILT UP SIDE.
4. TILT DOWN OPERATION
WHEN THE MOON ROOF CONTROL SW IS PUSHED TO TILT DOWN POSITION, WITH THE IGNITION SW TURNED ON AND THE MOON
ROOF TILTED UP (NO. 1 AND NO. 2 MOON ROOF LIMIT SWITCHES ARE BOTH OFF), A SIGNAL IS INPUT FROM TERMINAL 2 OF MOON
ROOF CONTROL SW TO TERMINAL 7 OF MOON ROOF CONTROL RELAY.
AS A RESULT, THE RELAY IS ACTIVATED AND THE CURRENT TO TERMINAL 6 OF RELAY FLOWS FROM TERMINAL 5 OF RELAY "
TERMINAL 1 OF MOON ROOF MOTOR " TERMINAL 3 " TERMINAL 4 OF RELAY " TERMINAL 11 " TO GROUND AND ROTATES THE
MOTOR SO THAT TILT DOWN OPERATION OCCURS AS LONG AS THE MOON ROOF CONTROL SW IS PUSHED ON THE TILT DOWN
SIDE. (DURING TILT DOWN, LIMIT SW NO. 1 IS CHANGED OFF TO ON.)
5. TILT UP REMINDER SYSTEM
WHEN THE IGNITION SW IS TURNED FROM ON TO ACC OR OFF WITH THE MOON ROOF STILL TILTED UP THE CURRENT DOES NOT
FLOW TO TERMINAL 6 OF MOON ROOF CONTROL RELAY.
THIS IS RECEIVED BY THE RELAY AS A SIGNAL THAT THE IGNITION SW IS TURNED OFF. AT THIS TIME, MOON ROOF LIMIT SW NO.1
AND NO. 2 ARE OFF, SO SIGNALS ARE INPUT TO TERMINALS 8 AND 9 OF MOON ROOF CONTROL RELAY THAT THE MOON ROOF IS
IN THE TILT OPERATION POSITION. WHEN THESE SIGNALS ARE INPUT TO THE MOON ROOF CONTROL RELAY, THE TIMER BUILT
INTO THE RELAY OPERATES.
THUS THE CURRENT TO TERMINAL 12 OF MOON ROOF CONTROL RELAY FLOWS THROUGH BUZZER OF MOON ROOF CONTROL
RELAY AND TERMINAL 11 OF MOON ROOF CONTROL RELAY TO GROUND AND THE BUZZER SOUNDS ABOUT 8 TIMES TO NOTIFY
THAT THE MOON ROOF IS STILL IN THE TILT UP CONDITION.
SYSTEM OUTLINE

171
CURRENT ALWAYS FLOWS TO TERMINAL 1 OF THE INTEGRATION RELAY THROUGH THE DOME FUSE.
1. SEAT BELT WARNING SYSTEM
WHEN THE IGNITION SW IS TURNED ON, CURRENT FLOWS FROM THE GAUGE FUSE TO THE TERMINAL 7 OF THE INTEGRATION
RELAY AT THE SAME TIME, CURRENT FLOWS TO TERMINAL 9 OF THE RELAY FROM THE GAUGE FUSE THROUGH THE SEAT BELT
WARNING LIGHT. THIS CURRENT ACTIVATES THE SEAT BELT WARNING RELAY AND, CURRENT FLOWING THROUGH THE WARNING
LIGHT FLOWS FROM TERMINAL 9 OF THE RELAY" TERMINAL 10 " GROUND, CAUSING THE WARNING LIGHT TO LIGHT UP. AT THE
SAME AS THE WARNING LIGHT LIGHTS UP. A BUCKLE SW OFF SIGNAL IS INPUT TO TERMINAL 8 OF THE RELAY, THE CURRENT
FLOWING TO TERMINAL 1 OF THE RELAY FLOWS FROM TERMINAL 10 " GROUND AND THE SEAT BELT WARNING BUZZER SOUNDS
FOR APPROX. 4±8 SECONDS. HOWEVER, IF SEAT BELT IS PUT ON DURING THIS PERIOD (WHILE THE BUZZER IS SOUNDING),
SIGNAL INPUT TO TERMINAL 8 OF THE RELAY STOPS AND THE CURRENT FLOW FROM TERMINAL 1 OF THE RELAY " TERMINAL 10
" GROUND IS CUT, CAUSING THE BUZZER TO STOP.
2. UNLOCK WARNING SYSTEM
WITH THE IGNITION KEY INSERTED IN THE KEY CYLINDER (UNLOCK WARNING SW ON), THE IGNITION SW STILL OFF AND DOOR
OPEN (DOOR COURTESY SW ON), WHEN A SIGNAL IS INPUT TERMINAL 5 AND 6 OF THE RELAY, THE INTEGRATION RELAY
OPERATES, CURRENT FLOWS FROM TERMINAL 1 OF THE RELAY " TERMINAL 10 " GROUND AND THE UNLOCK WARNING
BUZZER SOUNDS.
B 7, B 8 BUCKLE SW
1±2 : CLOSED WITH DRIVR'S LAP BELT IN USE
D12 DOOR COURTESY SW FRONT LH
1±GROUND : CLOSED WITH FRONT LH DOOR OPEN
INTEGRATION RELAY
10±GROUND : ALWAYS CONTINUITY
6±GROUND : CONTINUITY WITH FRONT LH DOOR OPEN
5±GROUND : CONTINUITY WITH IGNITION KEY IN CYLINDER
8±GROUND : CONTINUITY UNLESS DRIVER'S LAP BELT IN USE
9±GROUND :0 VOLTS WITH IGNITION SW ON AND BUCKLE SW OFF
1±GROUND : ALWAYS APPROX. 12 VOLTS
7±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
I12 UNLOCK WARNING SW [IGNITION SW]
1±5 : CLOSED WITH IGNITION KEY IN CYLINDER
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
B 732D1234 (S/D), 35 (C/P), 36 (W/G)J 536 (W/G)
B 832I1233
C 932J 133
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B
1C20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1G
20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1H20FLOOR NO. 1 WIRE J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
2E22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IO142FLOOR NO. 1 WIRE AND SEAT WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IG42INSTRUMENT PANEL BRACE LH
46 (S/D)
BL48 (C/P)UNDER THE LEFT QUARTER PILLARBL
50 (W/G)
UNDER THE LEFT QUARTER PILLAR
SYSTEM OUTLINE
SERVICE HINTS

178
SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
THE SRS (SUPPLEMENTAL RESTRAINT SYSTEM) IS A DRIVER AND PASSENGER PROTECTION DEVICE WHICH HAS A
SUPPLEMENTAL ROLE TO THE SEAT BELTS.
WHEN THE IGNITION SW IS TURNED TO ACC OR ON, CURRENT FROM THE CIG/RADIO FUSE FLOWS TO TERMINAL 14 OF THE
CENTER AIRBAG SENSOR ASSEMBLY. ONLY WHEN THE IGNITION SW IS ON DOES THE CURRENT FROM THE IGN FUSE FLOW TO
TERMINAL 13.
IF AN ACCIDENT OCCURS WHILE DRIVING, DECELERATION CAUSED BY A FRONTAL IMPACT IS DETECTED BY EACH SENSOR AND
SWITCH, AND WHEN THE FRONTAL IMPACT EXCEEDS A SET LEVEL (WHEN THE SAFING SENSOR BUILT INTO THE CENTER AIRBAG
SENSOR ASSEMBLY IS ON AND THE CENTER AIRBAG SENSOR IS ON, FRONT AIRBAG SENSORS ARE OFF), CURRENT FROM THE
CIG/RADIO OR IGN FUSE FLOWS TO TERMINALS 2, 3 OF THE CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 1 OF THE AIRBAG
SQUIB " SQUIB " TERMINAL 2 " TERMINALS 1, 4 OF CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 6, TERMINAL 5 OR BODY
GROUND " GROUND.
WHEN THE SAFING SENSOR BUILT INTO THE CENTER AIRBAG SENSOR ASSEMBLY IS ON AND THE FRONT AIRBAG SENSOR LH OR
RH IS ON, CENTER AIRBAG SENSOR IS OFF CURRENT FROM THE CIG/RADIO OR IGN FUSE FLOWS TO TERMINALS 2, 3 OF THE
CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 1 OF THE AIRBAG SQUIB " SQUIB " TERMINAL 2 " TERMINALS 1, 4 OF
CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 8 OR 11 " TERMINAL 1 OF FRONT AIRBAG SENSOR " TERMINAL 2 "
TERMINAL 9 OR 10 OF CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 6, TERMINAL 5 OR BODY GROUND " GROUND.
WHEN THE SAFING SENSOR BUILT INTO THE CENTER AIRBAG SENSOR ASSEMBLY IS ON, AND THE FRONT AIRBAG SENSOR LH OR
RH IS ON AND CENTER AIRBAG SENSOR IS ON ONE OF THE ABOVE±MENTIONED CIRCUITS IS ACTIVATED SO THAT CURRENT
FLOWS TO THE AIRBAG SQUIB AND CAUSES IT TO OPERATE. THE BAG STORED INSIDE THE STEERING WHEEL PAD IS
INSTANTANEOUSLY EXPANDED TO SOFTEN THE SHOCK TO THE DRIVER.
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A1532D 128 (1MZ±FE), 30 (5S±FE)F 228 (1MZ±FE), 30 (5S±FE)
C 332D 332J 433
C1032F 128 (1MZ±FE), 30 (5S±FE)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1F20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
3D24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IP144ENGINE WIRE AND COWL WIREIP344ENGINE WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IE42LEFT KICK PANEL
IG42INSTRUMENT PANEL BRACE LH
SYSTEM OUTLINE

BBB
BB B B BBB
BBB J2 J3
B
(
HINT : SEE PAGE 7)(
HINT : SEE PAGE 7)
12 N3B
13X
45612 S5 S10BLUE12K3
1 2 N2A
183
WHEN THE IGNITION SW IS TURNED TO ACC POSITION THE CURRENT FROM THE CIG/RADIO FUSE FLOWS TO TERMINAL 1 OF THE
SHIFT LOCK ECU. WHEN THE IGNITION SW IS TURNED TO ON POSITION THE CURRENT FROM THE ECU±IG FUSE FLOWS TO
TERMINAL 3 OF THE ECU.
1. SHIFT LOCK MECHANISM
WITH THE IGNITION SW ON, WHEN A SIGNAL THAT THE BRAKE PEDAL IS DEPRESSED (STOP LIGHT SW ON) AND A SIGNAL THAT
THE SHIFT LEVER IS PUT IN ªPº POSITION (CONTINUITY BETWEEN P1 AND P OF THE SHIFT LOCK CONTROL SW) IS INPUT TO THE
ECU, THE ECU OPERATES AND CURRENT FLOWS FROM TERMINAL 3 OF THE ECU " TERMINAL SL+ OF THE SHIFT LOCK
SOLENOID " SOLENOID " TERMINAL SL± " TERMINAL 5 OF THE ECU " GROUND. THIS CAUSES THE SHIFT LOCK SOLENOID TO
TURN ON (PLATE STOPPER DISENGAGES) AND THE SHIFT LEVER CAN SHIFT INTO OTHER POSITION THAN THE ªPº POSITION.
2. KEY INTERLOCK MECHANISM
WITH THE IGNITION SW IN ON OR ACC POSITION, WHEN THE SHIFT LEVER IS PUT IN ªPº POSITION (NO CONTINUITY BETWEEN P2
AND P OF SHIFT LOCK CONTROL SW), THE CURRENT FLOWING FROM TERMINAL 4 OF THE ECU " KEYINTERLOCK SOLENOID IS
CUT OFF. THIS CAUSES THE KEYINTERLOCK SOLENOID TO TURN OFF (LOCK LEVER DISENGAGES FROM LOCK POSITION) AND
THE IGNITION KEY CAN BE TURNED FROM ACC TO LOCK POSITION.
S 5 SHIFT LOCK ECU
1±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ACC OR ON POSITION
3±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
5±GROUND : ALWAYS CONTINUITY
6±GROUND : APPROX. 12 VOLTS WITH BRAKE PEDAL DEPRESSED
4±GROUND :0 VOLTS WITH IGNITION SW AT ACC POSITION AND SHIFT LEVER POSITION IN P POSITION
6±12 VOLTS WITH SHIFT LEVER POSITION IN EXCEPT P POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
J 233N 2A33S1033
J 333N 3B33
K 333S 533
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1L20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
II142COWL WIRE AND INSTRUMENT PANEL WIRE
II242INSTRUMENT PANEL WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IE42LEFT KICK PANELIF42LEFT KICK PANEL
SYSTEM OUTLINE
SERVICE HINTS

185
WITH THE IGNITION SW TURNED ON, THE CURRENT FLOWS TO TERMINAL 18 OF THE WIPER AND WASHER SW, TERMINAL 2 OF
THE WASHER MOTOR AND TERMINAL 4 OF THE WIPER MOTOR THROUGH THE WIPER FUSE.
1. LOW SPEED POSITION
WITH WIPER SW TURNED TO LOW POSITION, THE CURRENT FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW "
TERMINAL 7 " TERMINAL 3 OF THE WIPER MOTOR " WIPER MOTOR " TERMINAL 1 " TO GROUND AND CAUSES TO THE WIPER
MOTOR TO RUN AT LOW SPEED.
2. HIGH SPEED POSITION
WITH WIPER SW TURNED TO HIGH POSITION, THE CURRENT FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW "
TERMINAL 13 " TERMINAL 2 OF THE WIPER MOTOR " WIPER MOTOR " TERMINAL 1 " TO GROUND AND CAUSES TO THE WIPER
MOTOR TO RUN AT HIGH SPEED.
3. INT POSITION
WITH WIPER SW TURNED TO INT POSITION, THE RELAY OPERATES AND THE CURRENT WHICH IS CONNECTED BY RELAY
FUNCTION FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW " TERMINAL 16 " TO GROUND. THIS FLOW OF CURRENT
OPERATES THE INTERMITTENT CIRCUIT AND THE CURRENT FLOWS FROM TERMINAL 18 OF THE WIPER AND WASHER SW "
TERMINAL 7 " TERMINAL 3 OF THE WIPER MOTOR " TERMINAL 1 " TO GROUND AND THE WIPER FUNCTIONS.
THE INTERMITTENT OPERATION IS CONTROLLED BY A CONDENSER'S CHARGED AND DISCHARGED FUNCTION INSTALLED IN
RELAY AND THE INTERMITTENT TIME IS CONTROLLED BY A TIME CONTROL SW TO CHANGE THE CHARGING TIME OF THE
CONDENSER.
4. WASHER CONTINUOUS OPERATION
WITH WASHER SW TURNED TO ON, THE CURRENT FLOWS FROM TERMINAL 2 OF THE WASHER MOTOR " TERMINAL 1 "
TERMINAL 8 OF THE WIPER AND WASHER SW " TERMINAL 16 " TO GROUND AND CAUSES TO THE WASHER MOTOR TO RUN AND
WINDOW WASHER TO JET. THIS CAUSES THE CURRENT TO FLOW TO WASHER CONTINUOUS OPERATION CIRCUIT IN TERMINAL 18
OF THE WIPER AND WASHER SW " TERMINAL 7 " TERMINAL 3 OF THE WIPER MOTOR " TERMINAL 1 " TO GROUND AND THE
WIPER FUNCTION.
C13 FRONT WIPER AND WASHER SW (W/ WIPER RELAY) [COMB. SW]
16±GROUND : ALWAYS CONTINUITY
18±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
7±GROUND : APPROX. 12 VOLTS WITH WIPER AND WASHER SW AT LOW OR MIST POSITION
APPROX. 12 VOLTS 2 TO 12 SECONDS INTERMITTENTLY WITH WIPER SW AT INT POSITION
4±GROUND : APPROX. 12 VOLTS WITH IGNITION SW ON UNLESS WIPER MOTOR AT STOP POSITION
13±GROUND : APPROX. 12 VOLTS WITH WIPER AND WASHER SW AT HIGH POSITION
F 9 FRONT WIPER MOTOR
5±6 : CLOSED UNLESS WIPER MOTOR AT STOP POSITION
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C1332F 928 (1MZ±FE), 30 (5S±FE)W 128 (1MZ±FE), 30 (5S±FE)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1H20FLOOR NO. 1 WIRE J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IR144ENGINE ROOM MAIN WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EA38 (1MZ±FE)FRONT RIGHT FENDEREA40 (5S±FE)FRONT RIGHT FENDER
IE42LEFT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
E138 (1MZ±FE)ENGINE ROOM MAIN WIREI 544COWL WIREE 140 (5S±FE)ENGINE ROOM MAIN WIRE
SYSTEM OUTLINE
SERVICE HINTS

187
WHEN THE IGNITION SW IS TURNED ON, CURRENT FLOWS TO TERMINAL 2 OF WASHER MOTOR, TERMINAL 4 OF REAR WIPER
RELAY AND TERMINAL 1 OF REAR WIPER MOTOR THROUGH THE WIPER FUSE.
1. REAR WIPER NORMAL OPERATION
WITH THE IGNITION SW TURNED ON AND REAR WIPER AND WASHER SW TURNED ON, THE CURRENT FLOWING TO TERMINAL 4
OF REAR WIPER RELAY FLOWS TO TERMINAL 6 OF RELAY " TERMINAL 1 OF REAR WIPER AND WASHER SW " TERMINAL 16 "
TO GROUND. THUS, THE RELAY COIL IS ACTIVATED AND THE CURRENT TO TERMINAL 4 OF RELAY FLOWS TO TERMINAL 1 "
TERMINAL 4 OF REAR WIPER MOTOR " MOTOR " TERMINAL 2 " TO GROUND AND CAUSES THE MOTOR TO OPERATE THE
WIPER.
2. REAR WIPER INTERMITTENT OPERATION
WITH THE IGNITION SW TURNED ON AND REAR WIPER AND WASHER SW TURNED TO INT POSITION, THE CURRENT FLOWING TO
TERMINAL 4 OF REAR WIPER RELAY FLOWS TO TERMINAL 3 OF RELAY " TERMINAL 10 OF WIPER SW " TERMINAL 16 " TO
GROUND. AS A RESULT, THE RELAY OPERATES AND CURRENT FLOWS FROM TERMINAL 4 OF RELAY " TERMINAL 1 " TERMINAL
4 OF REAR WIPER MOTOR " MOTOR " TERMINAL 2 " TO GROUND, CAUSING THE MOTOR TO ROTATE TO OPERATE THE WIPER.
AT THIS TIME THE CONTACT IN THE WIPER MOTOR CLOSED AND THE CURRENT FLOWS FROM TERMINAL 1 OF REAR WIPER
MOTOR " TERMINAL 3 " TERMINAL 2 OF REAR WIPER RELAY " TERMINAL 1 " TERMINAL 4 OF REAR WIPER MOTOR "
TERMINAL 2 " TO GROUND.
THUS, THE INTERMITTENT±STOP CIRCUIT OPERATES, THE CONDENOR IN THE CIRCUIT CHARGES AND THE WIPER CONTINUES TO
OPERATE UNTIL REACHING THE STOP POSITION. AFTER THE WIPER STOPS, CURRENT DOES NOT FLOW TO THE
INTERMITTENT±STOP CIRCUIT FROM TERMINAL 2 OF RELAY, BUT THE CONDENSER DISCHARGES CURRENT INTO THE
INTERMITTENT CIRCUIT AND THE CIRCUIT OPERATES UNTIL THE CONDENSER DISCHARGE ENDS. AS A RESULT, THIS DISCHARGE
INTERVAL BECOMES THE INTERMITTENT TIME.
WHEN THE CURRENT IS DISCHARGED COMPLETELY, THE CURRENT FLOWING TO TERMINAL 4 OF RELAY FLOWS TO TERMINAL 3
" TERMINAL 10 OF REAR WIPER AND WASHER SW " TERMINAL 16 " TO GROUND.
THEN, THE CURRENT IN TERMINAL 4 OF RELAY FLOWS FROM TERMINAL 1 " TERMINAL 4 OF MOTOR " MOTOR " TERMINAL 2 "
TO GROUND AND ROTATES THE MOTOR. THROUGH REPEITION OF THIS PROCESS, INTERMITTENT OPERATION OF THE REAR
WIPER OCCURS.
3. WASHER OPERATION
WITH THE IGNITION SW ON AND THE REAR WIPER AND WASHER SW IS TURNED STRONGLY (WASHER SW ON), CURRENT FLOWS
FROM TERMINAL 2 OF WASHER MOTOR " TERMINAL 3 " TERMINAL 2 OF REAR WIPER AND WASHER SW " TERMINAL 16 " TO
GROUND SO THAT THE WASHER MOTOR ROTATES AND WINDOW WASHER EJECTS THE SPRAY, ONLY THE WHILE THE REAR
WASHER SW IS TURNED, WHEN THE REAR WIPER SW IS OFF, AND THE REAR WIPER AND WASHER SW IS THEN TURNED IN THE
OFF DIRECTION, WASHER LIQUID WILL ALSO SPLAY.
R19 REAR WIPER RELAY
4±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
7±GROUND : ALWAYS CONTINUITY
1±4 : POINTS CHANGES EVERY APPROX. 9±15 SECONDS INTERMITTENTLY WITH IGNITION SW ON AND WIPER SW AT
INT POSITION
W 1 WASHER MOTOR
2±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT ON POSITION
3±GROUND : CONTINUITY WITH WASHER SW TURNED ON
SYSTEM OUTLINE
SERVICE HINTS

189
CIGARETTE LIGHTER AND CLOCK
2G 2
I7
IE 1
F12
F243
W±BL±R
L±R
R L±R W±B
G GW±B W±B
FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
20A
DOME
JUNCTION
CONNECTOR
FROM TA IL FUSE CIGARETTE
LIGHTERCLOCK
J2C4
C6SERVI CE HI NTS
F F F C4 C6
J2DARK GRAYBLACK
(
HINT : SEE PAGE 7) 1
212
34
1D 715A
CIG/RADIO
3D 93C 21
1M 51C 8
C 4 CIGARETTE LIGHTER2±GROUND : APPROX. 12 VOLTS WITH IGNITION SW AT
ACC OR ON POSITION
1±GROUND : ALWAYS CONTINUITY
C 6
CLOCK3±GROUND : ALWAYS APPROX. 12 VOLTS (POWER FOR
CLOCK)
4±GROUND : APPROX .12 VOLTS WITH IGNITION SW AT
ACC OR ON POSITION
(POWER FOR INDICATION)
2±GROUND : APPROX .12 VOLTS WITH LIGHT CONTROL
SW AT TAIL OR HEAD POSITION
APPROX. 12 VOLTS WITH ENGINE
RUNNING AND PARKING BRAKE RELEASED
(CANADA)
1±GROUND : ALWAYS CONTINUITY
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C 432C 632J 233
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1B
1C20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1D20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M
2E22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IE42LEFT KICK PANEL
: SPLICE POINTS
CODESEE PAGEWIRE HARNESS WITH SPLICE POINTSCODESEE PAGEWIRE HARNESS WITH SPLICE POINTS
I 744COWL WIRE

196
CRUISE CONTROL
CURRENT IS APPLIED AT ALL TIMES THROUGH STOP FUSE TO TERMINAL 1 OF THE CRUISE CONTROL ECU AND TERMINAL 2 OF
STOP LIGHT SW, AND ALSO THROUGH THE STOP FUSE TO TERMINAL 15 OF CRUISE CONTROL ECU.
WITH THE IGNITION SW TURNED TO ON, THE CURRENT FLOWS THROUGH GAUGE FUSE TO TERMINAL (A) 6 OF COMBINATION
METER AND THE CURRENT THROUGH ECU±IG FUSE FLOWS TO TERMINAL 14 OF CRUISE CONTROL ECU.
WHEN THE IGNITION SW IS ON AND THE CRUISE CONTROL MAIN SW IS TURNED ON, A SIGNAL IS INPUT FROM TERMINAL 15 OF
CRUISE CONTROL MAIN SW TO TERMINAL 4 OF CRUISE CONTROL ECU. AS A RESULT, THE CRUISE CONTROL ECU FUNCTIONS
AND THE CURRENT TO TERMINAL 14 OF CRUISE CONTROL ECU TO TERMINAL 13 OF CRUISE CONTROL ECU " GROUND, AND
THE CRUISE CONTROL SYSTEM IS IN A CONDITION READY FOR OPERATION.
AT THE SAME TIME, THE CURRENT THROUGH THE GAUGE FUSE FLOWS FROM TERMINAL (A) 6 OF CRUISE CONTROL INDICATOR
LIGHT " TERMINAL (B) 9 " TERMINAL 5 OF CRUISE CONTROL ECU " TERMINAL 13 " TO GROUND, CAUSING THE CRUISE
CONTROL INDICATOR LIGHT TO LIGHT UP, INDICATING THAT THE CRUISE CONTROL IS READY FOR OPERATION.
1. SET OPERATION
WHEN THE CRUISE CONTROL MAIN SW IS TURNED ON AND THE SET SW IS TURNED ON WITH THE VEHICLE SPEED WITHIN THE
SET LIMIT (APPROX. 40 KM/H, 25 MPH TO 200 KM/H, 124 MPH), A SIGNAL IS INPUT TO TERMINAL 18 OF THE CRUISE CONTROL ECU
AND THE VEHICLE SPEED AT THE TIME THE SET SW IS RELEASED IS MEMORIZED IN THE ECU AS THE SET SPEED.
2. SET SPEED CONTROL
DURING CRUISE CONTROL DRIVING, THE ECU COMPARES THE SET SPEED MEMORIZED IN THE ECU WITH THE ACTUAL VEHICLE
SPEED INPUT INTO TERMINAL 20 OF THE CRUISE CONTROL ECU FROM THE VEHICLE SPEED SENSOR (SPEED SENSOR), AND
CONTROLS THE CRUISE CONTROL ACTUATOR TO MAINTAIN THE SET SPEED.
WHEN THE ACTUAL SPEED IS LOWER THAN THE SET SPEED, THE ECU CAUSES THE CURRENT TO THE CRUISE CONTROL
ACTUATOR TO FLOW FROM TERMINAL 12" TERMINAL 6 OF CRUISE CONTROL ACTUATOR "TERMINAL 7 "TERMINAL 11 OF
CRUISE CONTROL ECU. AS A RESULT, THE MOTOR IN THE CRUISE CONTROL ACTUATOR IS ROTATED TO OPEN THE THROTTLE
VALVE AND THE THROTTLE CABLE IS PULLED TO INCREASE THE VEHICLE SPEED. WHEN THE ACTUAL DRIVING SPEED IS HIGHER
THAN THE SET SPEED, THE CURRENT TO CRUISE CONTROL ACTUATOR FLOWS FROM TERMINAL 11 OF ECU "TERMINAL 7 OF
CRUISE CONTROL ACTUATOR "TERMINAL 6 "TERMINAL 12 OF CRUISE CONTROL ECU.
THIS CAUSES THE MOTOR IN THE CRUISE CONTROL ACTUATOR TO ROTATE TO CLOSE THE THROTTLE VALVE AND RETURN THE
THROTTLE CABLE TO DECREASE THE VEHICLE SPEED.
3. COAST CONTROL
DURING THE CRUISE CONTROL DRIVING, WHILE THE COAST SW IS ON, THE CRUISE CONTROL ACTUATOR RETURNS THE
THROTTLE CABLE TO CLOSE THE THROTTLE VALVE AND DECREASE THE DRIVING SPEED. THE VEHICLE SPEED WHEN THE COAST
SW IS TURNED OFF IS MEMORIZED AND THE VEHICLE CONTINUES AT THE NEW SET SPEED.
4. ACCEL CONTROL
DURING CRUISE CONTROL DRIVING, WHILE THE ACCEL SW IS TURNED ON, THE CRUISE CONTROL ACTUATOR PULLS THE
THROTTLE CABLE TO OPEN THE THROTTLE VALVE AND INCREASE THE DRIVING SPEED.
THE VEHICLE SPEED WHEN THE ACCEL SW IS TURNED OFF IS MEMORIZED AND THE VEHICLE CONTINUES AT THE NEW SET
SPEED.
5. RESUME CONTROL
UNLESS THE VEHICLE SPEED FALLS BELOW THE MINIMUM SPEED LIMIT (APPROX. 40 KM/H, 25 MPH) AFTER CANCELING THE SET
SPEED BY THE CANCEL SW, PUSHING THE RESUME SW WILL CAUSE THE VEHICLE TO RESUME THE SPEED SET BEFORE
CANCELLATION.
6. MANUAL CANCEL MECHANISM
IF ANY OF THE FOLLOWING OPERATIONS OCCURS DURING CRUISE CONTROL OPERATION, CURRENT FLOW TO MAGNETIC
CLUTCH OF THE ACTUATOR IS CUT TURNS OFF AND THE MOTOR ROTATES TO CLOSE THE THROTTLE VALVE AND THE CRUISE
CONTROL IS RELEASED.
*PLACING THE SHIFT LEVER IN ªNº POSITION (PARK/NEUTRAL POSITION SW (NEUTRAL START SW ON). ªSIGNAL INPUT TO
TERMINAL 2 OF ECUº (A/T)
*DEPRESSING THE CLUTCH PEDAL (CLUCH SW ON). ªSIGNAL INPUT TO TERMINAL 2 OF THE ECUº (M/T)
*DEPRESSING THE BRAKE PEDAL (STOP LIGHT SW ON). ªSIGNAL INPUT TO TERMINAL 16 OF ECUº
*PUSH THE CANCEL SW (CANCEL SW ON). ªSIGNAL INPUT TO TERMINAL 18 OF ECUº
*DEPRESSING THE PARKING BRAKE PEDAL (PARKING BRAKE SW ON). ªSIGNAL INPUT TO TERMINAL 3 OF ECUº (3VZ±FE)
*PULLING THE PARKING BRAKE LEVER (PARKING BRAKE SW ON). ªSIGNAL INPUT TO TERMINAL 3 OF THE ECUº (5S±FE)
SYSTEM OUTLINE

210
ABS (ANTI±LOCK BRAKE SYSTEM) (TMC MADE)
A B
A
E4
E6
I25E4 EC1 7EC1 3
IR2 6IR27IR25M
2 1 A 23 A24 A11 A1A13 A26 A14 A18 A6 B 4A1A4A3A6A2A5B1 A 5 A 1 B 4 B 2B3
A 2A15 A22 A10 A3A16B 3
B 1A2A4
A6
A 9
2 1
EAR±L
FR+ FR± FS S FL+ FL ± GND E
W±L W±L W±L
W±LG± W W±R
GR±L
GR±R
GR±G
L±W
G±W
L±R
G±R
R
R±W
W±R
W±BW±B
W±B W±B
W±B
BR BR R G W±B
B
W
W
W±B1FUSE BOX
60A ABS
ABS RELAY
ABS ACTUATOR
R±L
R± SR MR SFR SFL SRR SRL AST MT
ABS SPEED SENSOR
FRONT LHABS SPEED SENSOR
FRONT RH
W±B
(
SHIELDED)(
SHIELDED) ABS ECU FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
A1 3 , A 1 4 BA A6 , A7
B A4 , A5
A8 A9 F1 8
W±R
W±B
G
R