airbag TOYOTA CAMRY 1994 XV10 / 4.G Wiring Diagrams Workshop Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1994, Model line: CAMRY, Model: TOYOTA CAMRY 1994 XV10 / 4.GPages: 307, PDF Size: 5.48 MB
Page 28 of 307
28
ELECTRICAL WIRING ROUTING
Position of Parts in Engine Compartment
[1MZ±FE]
A 2 A/C Triple Pressure SW (A/C Dual and Single Pressure F 1 Front Airbag Sensor LH
SW) F 2 Front Airbag Sensor RH
A 3 A/C Magnetic Clutch and Lock Sensor F 3 Front Clearance Light LH
A 4 ABS Actuator F 4 Front Clearance Light RH
A 5 ABS Actuator F 5 Front Side Marker LH
A 6 ABS Relay F 6 Front Side Marker RH
A 7 ABS Relay F 7 Front Turn Signal Light LH
A 8 ABS Speed Sensor Front LH F 8 Front Turn Signal Light RH
A 9 ABS Speed Sensor Front RH F 9 Front Wiper Motor
F 10 Fuse Box
B 2 Brake Fluid Level SW F 16 Fuse Box
F 18 Fuse Box
C 2 Cruise Control Actuator
C 17 Camshaft Position Sensor G 1 Generator (Alternator)
C 18 Crankshaft Position Sensor G 2 Generator (Alternator)
D 1 Data Link Connector 1 (Check Connector) H 1 Headlight Hi LH
D 2 Distributor H 2 Headlight Hi RH
H 3 Headlight Lo LH
E 1 EGR Gas Temp. Sensor H 4 Headlight Lo RH
E 2 Electronic Controlled Transmission Solenoid H 5 Horn LH
E 4 Engine Coolant Temp. Sensor (EFI Water Temp. H 6 Horn RH
Sensor) H 11 Heated Oxygen Sensor (Bank 1 Sensor 1)
E 5 Engine Coolant Temp. Sensor (Water Temp. Sensor) H 12 Heated Oxygen Sensor (Bank 2 Sensor 1)
(for Cooling Fan)
Page 30 of 307
30
ELECTRICAL WIRING ROUTING
Position of Parts in Engine Compartment
[5S±FE]
A 1 A/C Condenser Fan Motor E 1 EGR Gas Temp. Sensor
A 2 A/C Triple Pressure SW (A/C Dual and Single Pressure E 2 Electronic Controlled Transmission Solenoid
SW) E 3 Electronic Controlled Transmission Solenoid
A 3 A/C Magnetic Clutch and Lock Sensor E 4 Engine Coolant Temp. Sensor (EFI Water Temp.
A 4 ABS Actuator Sensor)
A 5 ABS Actuator E 5 Water Temp. SW (for Cooling Fan)
A 6 ABS Relay
A 7 ABS Relay F 1 Front Airbag Sensor LH
A 8 ABS Speed Sensor Front LH F 2 Front Airbag Sensor RH
A 9 ABS Speed Sensor Front RH F 3 Front Clearance Light LH
F 4 Front Clearance Light RH
B 1 Back±Up Light SW (M/T) F 5 Front Side Marker LH
B 2 Brake Fluid Level SW F 6 Front Side Marker RH
F 7 Front Turn Signal Light LH
C 2 Cruise Control Actuator F 8 Front Turn Signal Light RH
F 9 Front Wiper Motor
D 1 Data Link Connector 1 (Check Connector) F 10 Fuse Box
D 2 Distributor F 16 Fuse Box
F 17 Fuse Box
F 18 Fuse Box
G 1 Generator (Alternator)
G 2 Generator (Alternator)
Page 32 of 307
32
ELECTRICAL WIRING ROUTING
Position of Parts in Instrument Panel
A 10 A/C Amplifier C 12 Combination SW
A 11 A/C Evaporator Temp. Sensor C 13 Combination SW
A 12 A/C SW C 14 Cooling Fan ECU
A 13 ABS ECU C 15 Cruise Control Clutch SW (M/T)
A 14 ABS ECU C 16 Cruise Control ECU
A 15 Airbag Squib (Steering Wheel Pad)
A 16 Air Inlet Control Servo Motor D 3 Data Lik Connector 2 (TDCL (Toyota Diagnostic
A 17 Air Vent Mode Control Servo Motor Communication Link))
A 18 Ashtray Illumination D 4 Daytime Running Light Relay (Main)
A 22 Airbag Squib (Front Passenger Airbag Assembly) D 5 Diode (for Cruise Control)
D 6 Diode (for Idle±Up)
B 3 Back Door Lock Control SW D 7 Diode (for Courtesy)
B 4 Blower Motor D 8 Door Lock Control Relay)
B 5 Blower Resistor D 24 Date Link Connector 3
B 6 Blower SW D 25 Diode (for Tension Reducer)
B 7 Buckle SW LH (w/ Power Seat)
B 8 Buckle SW LH (w/o Power Seat) E 6 Electronic Controlled Transmission Pattern Select SW
B 10 Buckle SW RH E 7 Engine Control Module (Engine and Electronic
Controlled Transmission ECU) (A/T)
C 3 Center Airbag Sensor Assembly E 8 Engine Control Module (Engine and Electronic
C 4 Cigarette Lighter Controlled Transmission ECU) (A/T)
C 5 Cigarette Lighter Illumination E 9 Engine Control Module (Engine and Electronic
C 6 ClockControlled Transmission ECU) (A/T)
C 7 Clutch Start SW (M/T) E 10 Engine Control Module (Engine and Electronic
C 8 Combination Meter Controlled Transmission ECU) (A/T)
C 9 Combination Meter E 11 Engine Control Module (Engine ECU) (M/T)
C 10 Combination Meter E 12 Engine Control Module (Engine ECU) (M/T)
C 11 Combination Meter E 14 Engine Control Module (Engine ECU) (M/T)
Page 55 of 307
55
192 17711 4
11 8
Cruise Control Actuator
C2 C5 C10 C11 C13 D8C12 C3 C4 C6 C8 C9 C14 C16 D1 D3 D4 D6 D7
Center Airbag Sensor Assembly
Cigarette Lighter
Cigarette Lighter Illumination
Clock
Combination Meter
(Turn Signal Indicator Light)Combination Meter
(Cruise Control Indicator Light)
Combination Meter
Combination Meter
(Meter Illmination)
Combination Meter
(Open Door Warning Light)
Combination Meter
(Seat Belt Warning Light)
Combination Meter
(Charge Warning Light)
Combination Meter
(High Beam Indicator Light)
Combination Meter
(Rear Light Warning Light)
Combination Meter
Combination Meter
(SRS Warning Light)
Combination Meter
(A/T Indicator Light)
Combination SW (Horn SW)
Combination SW
(Turn Signal SW)
Combination SW
(Light Control SW)
Combination SW
Front Wiper and Washer SW)
Cooling Fan ECU (1MZ±FE)
Cruise Control ECU
Data Link Connector 1
(Check Connector)
Data Link Connector 2
(TDCL (Toyota Diagnostic
Communication Link))
Daytime Running Light Relay
(Main) (CANADA)
Diode (for Idle±Up)
Diode (for Courtesy) (W/G) Door Lock Control Relay
18912618968
72192236210
21476 130
134
138
140 126120
124
144
148236126
198
204104
11 2
144244 80
90
98
214 90
192
214106
23680
90
98130
134
138
140156
140 104
106
D9 C717080
90
98177 17311 4
11 8106
126
148184
186192 98
204134
140
Diode (for Courtesy) Combination Meter
(Malfunction Indicator Light) Combination Meter
(ABS Warning Light) Clutch Start SW (M/T)
(4): R/B No. 4 (See page 20)(5): R/B No. 5 (See page 19)(6)R/B No. 6 (See Page )
2526 26
Page 58 of 307
58
POWER SOURCE (Current Flow Chart)
*Page Nos. of
Related Systems
Parts
Code or
Location
CB or Fuse
Location
* These are the page numbers of the first page on which the related system is shown.
The part indicated is located somewhere in the system, not necessarily on the page indicated here.
I5 I6 I7 I8 I9 I11 I12
I13I14 I16 I17 I18
I19 8068
72
80 130
134
138
140106
120
130
144
76
11 4
130
170
214
246
177
Injector No. 2
Injector No. 3
Injector No. 4
Injector No. 5 (1MZ±FE)
Injector No. 6 (1MZ±FE)
Injector Key Cylinder Light
Ignition SW and Unlock Warning
SW
Integration Relay
Interior Light
Ignition Coil No. 1 (1MZ±FE)
Ignition Coil No. 2 (1MZ±FE)
Ignition Coil No. 3 (1MZ±FE)
Ignition Coil No. 4 (1MZ±FE)
40A AM1
15A CIG/RADIO
40A DEFOG
15A ECU±1G
10A GAUGE
7.5A IGN
10A MIR±HTR
30A POWER
7.5A SRS
15A STOP
15A TAIL
7.5A TURN
20A WIPER
30A AM2
7.5A ALT±S
30A CDS FAN
20A DOME
15A ECU±B
15A EFI
10A HAZ
15A HEAD (LWR±LH)
15A HEAD (LWR±RH)
15A HEAD (UPR±LH)
15A HEAD (UPR±RH)
15A HEAD LH
15A HEAD RH
10A HORN
40A MAIN
7.5A OBD
10A STARTER
10A A/C
40A HEATER
7.5A DRL
100A ALT
60A ABS
Ignition Coil No. 5 (1MZ±FE)
Ignition Coil No. 6 (1MZ±FE)
Junction Connector
Junction Connector
Junction Connector
Junction Connector (for Airbag
System)
I20 I21 J1 J2 J3 J4 80 80 80 8011 2
126
140
17068
8068
8068
8068
8068
8068
80
90
11 8
134
192
224
252 98
120
138
210 80
154
182
190
204126
156
189
198
236130
156
182
214
226
234134
160
198
222
228
236154
168
204
224
230130
134
138
140130
134
138
140
[LOCATION](1)
(7): J/B No. 1 (See page 20)
: R/B No. 7 (See page )(2)
(8): J/B No. 2 (See page 19)
: Fuse Box (F10, F17 See
on page )(3): R/B No. 1 (See page 23)
2022
25
27
28 29
Page 174 of 307
174
SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
NOTICE: When inspecting or repairing the SRS (supplemental restraint system), perform the operation in
accordance with the following precautionary instructions and the procedure and precautions in the Repair
Manual for the applicable model year.
Malfunction symptoms of the supplemental restraint system are difficult to confirm, so the diagnostic trouble
codes become the most important source of information when troubleshooting.
When troubleshooting the supplemental restraint system, always inspect the diagnostic trouble codes before
disconnecting the battery.
Work must be started after 90 seconds from the time the Ignition SW is set to the ªLOCKº position and the
negative (±) terminal cable is disconnected from the battery.
(The supplemental restraint system is equipped with a back±up power source so that if work is started within
90 seconds of disconnecting the negative (±) terminal cable of the battery, the SRS may be activated.)
When the negative (±) terminal cable is disconnected from the battery, memory of the clock and audio systems
will be cancelled. So before starting work, make a record of the contents momorized by each memory system.
When work is finished, reset the clock and audio system as before and adjust the clock. This vehicle has tilt
and telescopic steering, power seat and outside rear view mirror and power shoulder belt anchorage, which
are all equipped with memory function, it is not possible to make a record of the customer, and ask the
customer to adjust the features and reset the memory.
To avoid erasing the memory of each memory system, never use a back±up power supply from outside the
vehicle.
When removing the steering wheel pad or handling a new steering wheel pad, keep the pad upper surface
facing upward. Also, lock the lock lever of the twin lock type connector at the rear of the pad and take care
not to damage the connector.
(Storing the pad with its metallic surface up may lead to a serious accident if the SRS inflates for some reason.)
Store the steering wheel pad where the ambient temperature remains below 93°C (200°F), without high
humidity and away from electrical noise.
Never use SRS parts from another vehicle. When replacing SRS parts, replace them with new parts.
Never disassemble and repair the steering wheel pad, center SRS sensor assembly or front airbag sensors.
Before repairing the body, remove the airbag sensors if during repair shocks are likely to be applied to the
sensors due to vibration of the body or direct tapping with tools or other parts.
Do not reuse a steering wheel pad or front airbag sensors.
After evaluating whether the center airbag sensor assembly is damaged or not, decide whether or not to reuse
it. (See the Repair Manual for the method for evaluating the center airbag sensor assembly.)
When troubleshooting the supplemental restraint system, use a high±impedance (Min. 10k/V) tester.
The wire harness of the supplemental restraint system is integrated with the cowl wire harness assembly and
engine wire harness assembly.
The vehicle wiring harness exclusively for the airbag system is distinguished by corrugated yellow tubing, as
are the connectors.
Do not measure the resistance of the airbag squib.
(It is possible this will deploy the airbag and is very dangerous.)
If the wire harness used in the supplemental restraint system is damaged, replace the whole wire harness
assembly.
When the connector to the airbag front sensors can be repaired alone (when there is no damage to the wire
harness), use the repair wire specially designed for the purpose.
(Refer to the Repair Manual for the applicable Model year for details of the replacement method.)
INFORMATION LABELS (NOTICES) are attached to the periphery of the SRS components. Follow the
instructions on the notices.
Page 177 of 307
177
IP 1 12 IP38
12
FRONT AIRBAG
SENSOR LHAIRBAG SQUIB
(
STEERING
WHEEL PAD) SPIRAL
CABLE
F1A1512 4 5 11B±O
P±L
B±Y
Y±B
LG±RB±Y
W±B W±BWB WB
±SL +SLD+ D± E1 E2 IG2 ACCLA FROM POWER SOURCE SYSTEM(
SEE PAGE 64)
DATA LINK CONNE CTOR 2
(
TDCL)DATA LINK CONNECOR 1
(
CHECK CONNECTOR)
AB TC AB TC D3 D1
CENTER AIRBAG SENSOR
ASSEMBLY C3 SRS WARNING LIGHT
[COMB. METER] C10
Y±B
21
W±B W±BW±R
B±Y
Y±BB±Y
LG±R B±Y
TC
IG IEC C B B B
13 1412 7C B
11 1034 5 6JUNCTION CONNECTOR
(
FOR SRS) J4
21
AIRBAG SQUIB
(
FRONT PASSENGER
AIRBAG ASSEMBLY) A22
B W
P± P+
12
12
AB CONNE CTION
DE TECTION
PIN12
AB CONNE CTION
DE TE CTION
PIN
WB
±SR +SR
89
FRONT AI RB AG
SENSOR RH F2
1F 91F 31F7. 5A
IGN15A
CIG/RADIO7. 5A
SRS
5
3D 16
3D 17
1M 11M51F 2 1F 1
Page 178 of 307
178
SRS (SUPPLEMENTAL RESTRAINT SYSTEM)
THE SRS (SUPPLEMENTAL RESTRAINT SYSTEM) IS A DRIVER AND PASSENGER PROTECTION DEVICE WHICH HAS A
SUPPLEMENTAL ROLE TO THE SEAT BELTS.
WHEN THE IGNITION SW IS TURNED TO ACC OR ON, CURRENT FROM THE CIG/RADIO FUSE FLOWS TO TERMINAL 14 OF THE
CENTER AIRBAG SENSOR ASSEMBLY. ONLY WHEN THE IGNITION SW IS ON DOES THE CURRENT FROM THE IGN FUSE FLOW TO
TERMINAL 13.
IF AN ACCIDENT OCCURS WHILE DRIVING, DECELERATION CAUSED BY A FRONTAL IMPACT IS DETECTED BY EACH SENSOR AND
SWITCH, AND WHEN THE FRONTAL IMPACT EXCEEDS A SET LEVEL (WHEN THE SAFING SENSOR BUILT INTO THE CENTER AIRBAG
SENSOR ASSEMBLY IS ON AND THE CENTER AIRBAG SENSOR IS ON, FRONT AIRBAG SENSORS ARE OFF), CURRENT FROM THE
CIG/RADIO OR IGN FUSE FLOWS TO TERMINALS 2, 3 OF THE CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 1 OF THE AIRBAG
SQUIB " SQUIB " TERMINAL 2 " TERMINALS 1, 4 OF CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 6, TERMINAL 5 OR BODY
GROUND " GROUND.
WHEN THE SAFING SENSOR BUILT INTO THE CENTER AIRBAG SENSOR ASSEMBLY IS ON AND THE FRONT AIRBAG SENSOR LH OR
RH IS ON, CENTER AIRBAG SENSOR IS OFF CURRENT FROM THE CIG/RADIO OR IGN FUSE FLOWS TO TERMINALS 2, 3 OF THE
CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 1 OF THE AIRBAG SQUIB " SQUIB " TERMINAL 2 " TERMINALS 1, 4 OF
CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 8 OR 11 " TERMINAL 1 OF FRONT AIRBAG SENSOR " TERMINAL 2 "
TERMINAL 9 OR 10 OF CENTER AIRBAG SENSOR ASSEMBLY " TERMINAL 6, TERMINAL 5 OR BODY GROUND " GROUND.
WHEN THE SAFING SENSOR BUILT INTO THE CENTER AIRBAG SENSOR ASSEMBLY IS ON, AND THE FRONT AIRBAG SENSOR LH OR
RH IS ON AND CENTER AIRBAG SENSOR IS ON ONE OF THE ABOVE±MENTIONED CIRCUITS IS ACTIVATED SO THAT CURRENT
FLOWS TO THE AIRBAG SQUIB AND CAUSES IT TO OPERATE. THE BAG STORED INSIDE THE STEERING WHEEL PAD IS
INSTANTANEOUSLY EXPANDED TO SOFTEN THE SHOCK TO THE DRIVER.
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
A1532D 128 (1MZ±FE), 30 (5S±FE)F 228 (1MZ±FE), 30 (5S±FE)
C 332D 332J 433
C1032F 128 (1MZ±FE), 30 (5S±FE)
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1F20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1M20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
3D24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
IP144ENGINE WIRE AND COWL WIREIP344ENGINE WIRE AND COWL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
IE42LEFT KICK PANEL
IG42INSTRUMENT PANEL BRACE LH
SYSTEM OUTLINE
Page 237 of 307
237
*
1 : W/O A/T INDICATOR LIGHT
* 2 : W/ A/T INDICATOR LIGHT
*
3 : MALFUNCTION INDICATOR LAMP
(
CHECK ENGINE WARNING LIGHT)
*7 : 5S±FE *
6 : 1MZ±FE * 5 : TMM MADE
*
4:TMCMADE
AB
C
COMBINATION METER1
IEIF 2 1B 15 B3B9B13
B 12B 8B14 C 1 C 3 A 9A 10C 2
II1 4
11B DE 18 A
FB E D
8 A
FAFROM POWER SOURCE SYSTEM(
SEE PAGE 64)
B±W
R±Y
R±GW±R Y±G B±W
B±O G± L
G±R
R±Y R±Y W±BG±RG± L
±B W±B
R±W R±W
R±W
G±O
Y
B±Y
R±BB±YY G±O R±Y
R±Y
R±W 10A
STARTER
TO LIGHT FAILURE
SENSOR
FROM º HEAD RHº FUSE
FROM º HEAD(
UP R±RH)
ºFUSE
(
CA NADA) (
USA) CRUISE
(
*3)
BRAKE
BULB
CHECK
RE AR LIGHT
O/D OFF
CHARGE
SRS
HIGH BEAM
PKB BRK
TOO/DMAINSW
TO GENERATOR(
ALTERNATOR)
TO CENTER AIRBAG
SENSOR ASSEMBLY
TO DIMMER SW
[COMB. SW] TO CRUISE CONTROL ECU
TO E NGINE CONTROL MODULE
(
ENGINE AND ELECTRONIC CONTROLLED
TRANSMISSION ECU)(
A/T)
TO E NGINE CONTROL MODULE
(
ENGINE ECU)(
M/T)
BRAKE FLUID
LEVEL SWJUNCTION
CONNECTOR
JUNCTION
CONNE CTOR
DAYTIME RUNNING
LIGHT RELAY
(
MAIN) PARKING
BRAKE SW
PARKING
BRAKE SW(
EX. 1MZ±FE A/T)
(
1MZ±FE A/T)
JUNCTION
CONNECTOR
JUNCTION
CONNECTOR (
USA)
(
CANA DA) C8 ,C9 , C10
J2
J2 B2
P3
P2 D4
J2
J3(
*1) (
*1)
(
USA)
II1 2
I6
G±O
G±O G±O
(
*2) FROM A/T
INDICATOR LIGHT
W±B
(
CA NADA)(
*5) (
*5)
O
(
*4)O
(
*4)
4
3B 203C 2
1D 31F3 7. 5A
IGN7. 5A
SRS
3B 19 3D19 3B 83D18
3D 83C8 3A 10
1M 51C 8
W
Page 256 of 307
256
GROUND POINT*3 :W/POWERWINDOW *
2:TMMMADE * 1 : TMC MADE
* 6 : AIR CONDITIONING(
LEVER CONTROL SW TYPE) *
5 : AIR CONDITIONING(
PUSH CONTROL SW TYPE) * 4 : W/O POWER WINDOW
LIGHT CONTROL SW
[COMB. SW]
KEY INTERLOCK
SOLENOID
WIPER AND WASHER SW
[COMB. SW]
RE AR WINDOW
DEFOGGER SW
CLOCK
CIGARETTE LIGHTER
BRAKE FLUID LEVEL
SW
TURN SIGNAL FLASHER
MOON ROOF
CONTROL RELAY
MOON ROOF MOTOR
MOON ROOF LIMIT SW
RADIO AND PLAYER
STEREO COMPONENT
AMPLIFIERBLOWER RESISTOR
A/C AMPLIFIER HEATER CONTROL SW
(
PUSH CONTROL SW
TYPE)
OR AIR VENT
MODE CONTROL SW
(
LEVER CONTROL SW
TYPE) BLOWER SW
STARTER RELAY
COMBINATION METER
CIRCUIT OPENING
RELAY
DAYTIME RUNNING
LIGHT RELAY(
MAIN)
CRUISE CONTROL ECU
CRUISE CONTROL SW
[COMB. SW]
HEATER RELAY I7
I7
I7
I7
I7
I13I13 I13 I13 I12
IH IG II2F
4 1
IM27F FI5
I5 W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
W±B
BR
BR BRW±B W±BW±B
W±B
W±B W±BW±B
W±B
W±B
W±B
W±B
W±B W±B
W±B
W±B W±B
W±B W±B
W±B W±BW±BW±B W±B W±B W±B
W±B
W±BW±B
W±B
VANI TY LIGHT LHAIR VENT MODE CONTROL
SERVO MOTOR
W±B
W±B W±B W±B JUNCTION
CONNE CTOR J1
DIMMER SW
[COMB. SW]
IL17 IK 14
W±B
W±B
CENTER AIRBAG SENSOR
ASSEMBLY(
E2)6
VANITY LIGHT RHW±B W±B
W±B
W±B
MOON ROOF CONTROL SW
AND PERSONAL LI GHT
(
W/ CD PL AYER)(
CANADA)
(
W/O CD PLAYER)IE
W±BIV 2 IV1
(
W/G)(
S /D, C/P) (
*1)W±B W±B
(
*2)
(
*2)
B5:S/D
B21 : C/P
B32 : W/G
B4:S/D
B21 : C/P
B31 : W/G
BK : S/D, C/P
BP : W/G
6 6 W±B
I5
W±B
DA TA LINK
CONNE CTOR 3
F W±B
B4:S/D
B30 : W/G
B20 : C/PI7:*5
I14 : * 6
1 HIGH BEAM INDICATOR
LIGHT [COMB. METER]
CRUISE CONTROL
CLUCH SW W±B
NOISE FILTER
POWER MAIN RELAY
INTEGRATION RELAY
UNLOCK WARNING SW
[IGNITION SW] 1C11
W±B W±B
CENTER AIRBAG SENSOR
ASSEMBLY(
E1)
1G4
1F1
1M1
1I6 1F2
1M 51C 8
3C
3D6
3A13
3A12
3B5
3C 186
3B14DEFOGGER RELAY 1C10