service indicator TOYOTA CAMRY 1994 XV10 / 4.G Wiring Diagrams Workshop Manual

84
ENGINE CONTROL (1MZ±FE)
CIRCUIT OPENING RELAY2±1 : CLOSED WITH STARTER RUNNING OR MEASURING PLATE (VOLUME AIR FLOW (AIR FLOW METER)) OPEN
EFI MAIN RELAY2±4 : CLOSED WITH IGNITION SW AT ON OR ST POSITION
E 4
ENGINE COOLANT TEMP. SENSOR (EFI WATER TEMP. SENSOR) 1±2 : 10.0 ± 20.0 K (±20°C, ±4°F)
: 4.0 ± 7.0 K (0°C, 32°F)
: 2.0 ± 3.0 K (20°C, 68°F)
: 0.9 ± 1.3 K (40°C, 104°F)
: 0.4 ± 0.7 K (60°C, 140°F)
: 0.2 ± 0.4 K (80°C, 176°F)
E 7(A), E 8(B), E 9(C), E10(D)
ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED
TRANSMISSION ECU)
VOLTAGE AT ENGINE CONTROL MODULE (ECU) WIRING CONNECTOR
BATT ± E1: ALWAYS 9.0±14.0 VOLTS
+B ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
+B1 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
IDL ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY OPEN)
0±3.0 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY CLOSED)
VC ± E1: ALWAYS 4.5±5.5 VOLTS (IGNITION SW AT ON POSITION)
VTA ± E1:0.3±0.8 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY CLOSED)
3.2±4.9 VOLTS (IGNITION SW ON AND THROTTLE VALVE FULLY OPEN)
VG ± E1:4.0±5.5 VOLTS (IGNITION SW AT ON POSITION)
THA ± E1:0.5±3.4 VOLTS (IGNITION SW ON AND INTAKE AIR TEMP. 20°C, 68°F)
THW ± E1:0.2±1.0 VOLTS (ENGINE IDLING AND COOLANT TEMP. 80°C, 176°F)
#10, #20, #30, #40, #50, #60
± E01:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
PULSE GENERATION (ENGINE IDLING)
IGT1, IGT2, IGT3
IGT4, IGT5, IGT6 ± E1: PULSE GENERATION (ENGINE IDLING)
IGF ± E1:4.5±5.5 VOLTS (IGNITION SW AT ON POSITION)
PULSE GENERATION (ENGINE IDLING)
G22+ ± G±: PULSE GENERATION (ENGINE IDLING)
NE+ ± G±: PULSE GENERATION (ENGINE IDLING)
RSC, RSO ± E1: PULSE GENERATION (ENGINE IDLING AND A/C OPERATION)
OXS, OXL, OXR ± E1: PULSE GENERATION (MAINTAIN ENGINE SPEED AT 2500 RPM FOR TWO MINUTES AFTER WARMING UP)
HTS, HTL, HTR ± E01:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
0±3.0 VOLTS (ENGINE IDLING)
KNKL, KNLR ± E1: PULSE GENERATION (ENGINE IDLING)
NSW ± E1:9.0±14.0 VOLTS (IGNITION SW ON AND OTHER SHIFT POSITION IN P OR N POSITION)
BELOW 3.0 VOLTS (IGNITION SW ON AND SHIFT POSITION IN P OR N POSITION)
SP1 ± E1: PULSE GENERATION (IGNITION SW ON AND ROTATE DRIVING WHEEL SLOWLY)
TE1 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
TE2 ± E1:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
W ± E1: BELOW 3.0 VOLTS (MULFUNCTION INDICATOR LAMP ON)
9.0±14.0 VOLTS (MULFUNCTION INDICATOR LAMP OFF AND ENGINE RUNNING)
A/C ± E1: BELOW 1.5 VOLTS (ENGINE IDLING AND A/C SW ON)
7.5±14.0 VOLTS (A/C SW OFF)
ACT ± E1:9.0±14.0 VOLTS (ENGINE IDLING AND A/C SW ON)
BELOW 1.5 VOLTS (A/C SW OFF)
ACIS ± E01:9.0±14.0 VOLTS (IGNITION SW AT ON POSITION)
STA ± E1:6.0 VOLTS OR MORE (ENGINE CRANKING)
I 4, I 5, I 6, I 7, I 8, I 9
INJECTOR1±2 : APPROX. 13.8 
T 1
THROTTLE POSITION SENSOR3±1 :0.2±5.7 KWITH CLEARANCE BETWEEN LEVER AND STOP SCREW 0 MM (0 IN.)
2±1 : LESS THAN 2.3 KWITH CLEARANCE BETWEEN LEVER AND STOP SCREW 0.5 MM (0.020 IN.)
WITH CLEARANCE BETWEEN LEVER AND STOP SCREW 0.7 MM (0.0276 IN.)
3±1 :2.0±10.2 KWITH THROTTLE VALVE FULLY OPEN
SERVICE HINTS

202
ELECTRONIC CONTROLLED TRANSMISSION AND A/T INDICATOR (1MZ±FE)
E 7(B), E 8 (C), E10(A)ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU)
(TURN ON THE IGNTION SW)
S1, S2± E1 : 9.0±14.0 VOLTS WITH SOLENOID ON
0±1.5 VOLTS WITH SOLENOID OFF
P± E1:7.5±14.0 VOLTS WITH IGNITION SW ON AND PATTERN SELECT SW AT POWER POSITION
L± E1:7.5±14.0 VOLTS WITH SHIFT LEVER AT L POSITION
2± E1:7.5±14.0 VOLTS WITH SHIFT LEVER AT 2 POSITION
R± E1:7.5±14.0 VOLTS WITH SHIFT LEVER AT R POSITION
STP± E1:9.0±14.0 VOLTS WITH BRAKE PEDAL DEPRESSED
THW± E2:0.2±1.0 VOLTS WITH WITH ENGINE COOLANT TEMP. 60°C (140°F) ±120°C (248°F)
IDL± E2:0±1.5 VOLTS WITH THROTTLE VALVE FULLY CLOSED
9.0±14.0 VOLTS WITH THROTTLE VALVE FULLY OPENED
VTA±E2:0.3±0.8 VOLTS WITH THROTTLE VALVE FULLY CLOSED
3.2±4.9 VOLTS WITH THROTTLE VALVE FULLY OPENED
VC± E2:4.5±5.5 VOLTS WITH IGNITION SW AT ON POSITION
OD1± E1:4.5±5.5 VOLTS WITH IGNITION SW AT ON POSITION
OD2± E1:9.0±14.0 VOLTS WITH O/D MAIN SW TURNED OFF
0±3.0 VOLTS WITH O/D MAIN SW TURNED ON
IGSW± E1:9.0±14.0 VOLTS WITH IGNITION SW AT ON POSITION
+B± E1:9.0±14.0 VOLTS WITH IGNITION SW AT ON POSITION
+B1± E1:9.0±14.0 VOLTS WITH IGNITION SW AT ON POSITION
E 2
ELECTRONIC CONTROLLED TRANSMISSION SOLENOID1, 2, 6±GROUND : EACH 11±15 W
O 5 O/D MAIN SW1±3 : CLOSED WITH O/D MAIN SW OFF, OPEN WITH O/D MAIN SW ON
: PARTS LOCATION
CODESEE PAGECODESEE PAGECODESEE PAGE
C 832E 9C32O 533
C1132E10D32O 629
D 128J 133P 129
E 228J 233S1033
E 428J 333T 129
E 632J 733V 529
E 7A32N 2A33
E 8B32N 3B33
: JUNCTION BLOCK AND WIRE HARNESS CONNECTOR
CODESEE PAGEJUNCTION BLOCK AND WIRE HARNESS (CONNECTOR LOCATION)
1A
1D20COWL WIRE AND J/B NO 1 (INSTRUMENT PANEL LEFT)1K20COWL WIRE AND J/B NO. 1 (INSTRUMENT PANEL LEFT)
1M
2B22ENGINE ROOM MAIN WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
2C22ENGINE WIRE AND J/B NO 2 (ENGINE COMPARTMENT LEFT)2D22ENGINE WIRE AND J/B NO. 2 (ENGINE COMPARTMENT LEFT)
3B
3C24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
3D
24COWL WIRE AND J/B NO. 3 (BEHIND COMBINATION METER)
: CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS
CODESEE PAGEJOINING WIRE HARNESS AND WIRE HARNESS (CONNECTOR LOCATION)
II142COWL WIRE AND INSTRUMENT PANEL WIRE
II242INSTRUMENT PANEL WIRE AND COWL WIRE
IN142INSTRUMENT PANEL WIRE AND SWITCH WIRE
IP144ENGINE WIRE AND COWL WIREIP344ENGINE WIRE AND COWL WIRE
IQ144ENGINE WIRE AND INSTRUMENT PANEL WIRE
: GROUND POINTS
CODESEE PAGEGROUND POINTS LOCATION
EB38 (1MZ±FE)FRONT LEFT FENDER
ED38 (1MZ±FE)INTAKE MANIFOLD LH
IF42LEFT KICK PANEL
SERVICE HINTS

206
ELECTRONIC CONTROLLED TRANSMISSION AND A/T INDICATOR (5S±FE)
PREVIOUS AUTOMATIC TRANSMISSIONS HAVE SELECTED EACH GEAR SHIFT USING MECHANICALLY CONTROLLED THROTTLE
HYDRAULIC PRESSURE, GOVERNOR HYDRAULIC PRESSURE AND LOCK±UP HYDRAULIC PRESSURE. THE ELECTRONIC
CONTROLLED TRANSMISSION, HOWEVER, ELECTRICALLY CONTROLS THE LINE PRESSURE AND LOCK±UP PRESSURE ETC.,
THROUGH THE SOLENOID VALVE. ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU)
CONTROL OF THE SOLENOID VALVE BASED ON THE INPUT SIGNALS FROM EACH SENSOR MAKES SMOOTH DRIVING POSSIBLE BY
SHIFT SELECTION FOR EACH GEAR WHICH IS MOST APPROPRIATE TO THE DRIVING CONDITIONS AT THAT TIME.
1. GEAR SHIFT OPERATION
DURING DRIVING, THE ENGINE CONTROL MODULE (ECU) SELECTS THE SHIFT FOR EACH GEAR WHICH IS MOST APPROPRIATE TO
THE DRIVING CONDITIONS, BASED ON INPUT SIGNALS FROM THE ENGINE COOLANT TEMP. SENSOR (EFI WATER TEMP. SENSOR)
TO TERMINAL THW OF THE ENGINE CONTROL MODULE (ECU), AND ALSO THE INPUT SIGNALS TO TERMINAL SP1 OF THE ENGINE
CONTROL MODULE (ECU) FROM THE VEHICLE SPEED SENSOR (SPEED SENSOR) DEVOTED TO THE ELECTRONIC CONTROLLED
TRANSMISSION. CURRENT IS THEN OUTPUT TO THE ELECTRONIC CONTROLLED TRANSMISSION SOLENOIDS. WHEN SHIFTING TO
1ST SPEED, CURRENT FLOWS FROM TERMINAL S1 OF THE ENGINE CONTROL MODULE (ECU) " TERMINAL (A)3 OF THE
ELECTRONIC CONTROLLED TRANSMISSION SOLENOIDS " GROUND, AND CONTINUITY TO THE NO. 1 SOLENOID CAUSES THE
SHIFT.
FOR 2ND SPEED, CURRENT FLOWS FROM TERMINAL S1 OF THE ENGINE CONTROL MODULE (ECU) " TERMINAL (A)3 OF THE
ELECTRONIC CONTROLLED TRANSMISSION SOLENOIDS " GROUND, AND FROM TERMINAL S2 OF THE ENGINE CONTROL
MODULE (ECU) " TERMINAL (A)1 OF THE ELECTRONIC CONTROL TRANSMISSION SOLENOIDS " GROUND, AND CONTINUITY TO
SOLENOIDS NO. 1 AND NO. 2 CAUSES THE SHIFT.
FOR 3RD SPEED, THERE IS NO CONTINUITY TO NO. 1 SOLENOID, ONLY TO NO. 2, CAUSING THE SHIFT.
SHIFTING INTO 4TH SPEED (OVERDRIVE) TAKES PLACE WHEN THERE IS NO CONTINUITY TO EITHER NO. 1 OR NO. 2 SOLENOID.
2. LOCK±UP OPERATION
WHEN THE ENGINE CONTROL MODULE (ECU) JUDGES FROM EACH SIGNAL THAT LOCK±UP OPERATION CONDITIONS HAVE BEEN
MET, CURRENT FLOWS FROM TERMINAL SL OF THE ENGINE CONTROL MODULE (ECU) " TERMINAL (B)1 OF THE ELECTRONIC
CONTROLLED TRANSMISSION SOLENOID " GROUND, CAUSING CONTINUITY TO THE LOCK±UP SOLENOID AND CAUSING
LOCK±UP OPERATION.
3. STOP LIGHT SW CIRCUIT
IF THE BRAKE PEDAL IS DEPRESSED (STOP LIGHT SW ON) WHEN DRIVING IN LOCK±UP CONDITION, A SIGNAL IS INPUT TO
TERMINAL B/K OF THE ENGINE CONTROL MODULE (ECU), THE ENGINE CONTROL MODULE (ECU) OPERATES AND CONTINUITY TO
THE LOCK±UP SOLENOID IS CUT.
4. OVERDRIVE CIRCUIT
*O/D MAIN SW ON
WHEN THE O/D MAIN SW IS TURNED ON (O/D OFF INDICATOR LIGHT TURNS OFF), A SIGNAL IS INPUT TO TERMINAL OD2 OF THE
ENGINE CONTROL MODULE (ECU) AND ENGINE CONTROL MODULE (ECU) OPERATION CAUSES GEAR SHIFT WHEN THE
CONDITIONS FOR OVERDRIVE ARE MET.
*O/D MAIN SW OFF
WHEN THE O/D MAIN SW IS TURNED TO OFF, THE CURRENT FLOWING THROUGH THE O/D OFF INDICATOR LIGHT FLOWS
THROUGH THE O/D MAIN SW TO GROUND. CAUSING THE INDICATOR LIGHT TO LIGHT UP. AT THE SAME TIME, A SIGNAL IS INPUT
TO TERMINAL OD2 OF THE ENGINE CONTROL MODULE (ECU) AND ENGINE CONTROL MODULE (ECU) OPERATION PREVENTS
SHIFT INTO OVERDRIVE.
5. ELECTRONIC CONTROLLED TRANSMISSION PATTERN SELECT SW CIRCUIT
IF THE ELECTRONIC CONTROLLED TRANSMISSION PATTERN SELECT SW IS CHANGED FROM NORMAL TO POWER, THE CURRENT
FLOWING THROUGH THE POWER INDICATOR FLOWS TO GROUND, CURRENT FLOWS TO TERMINAL P OF THE ENGINE CONTROL
MODULE (ECU), THE ENGINE CONTROL MODULE (ECU) OPERATES, AND SHIFT UP AND SHIFT DOWN OCCUR AT HIGHER VEHICLE
SPEEDS THAN WHEN THE SW IS IN NORMAL POSITION.
E 7(C), E 8 (B), E10(A)ENGINE CONTROL MODULE (ENGINE AND ELECTRONIC CONTROLLED TRANSMISSION ECU)
(TURN ON THE IGNTION SW)
S1, S2 ±E1 :9.0±14.0 VOLTS WITH SOLENOID ON
0±1.5 VOLTS WITH SOLENOID OFF
P ±E1:7.5±14.0 VOLTS WITH IGNITION SW ON AND PATTERN SELECT SW AT POWER POSITION
L± E1:7.5±14.0 VOLTS WITH SHIFT LEVER AT L POSITION
2± E1:7.5±14.0 VOLTS WITH SHIFT LEVER AT 2 POSITION
R± E1:7.5±14.0 VOLTS WITH SHIFT LEVER AT R POSITION
B/K± E1:9.0±14.0 VOLTS WITH BRAKE PEDAL DEPRESSED
THW± E2:0.2±1.0 VOLTS WITH WITH ENGINE COOLANT TEMP. 60°C (140°F) ±120°C (248°F)
IDL± E2:0±1.5 VOLTS WITH THROTTLE VALVE FULLY CLOSED
9.0±14.0 VOLTS WITH THROTTLE VALVE FULLY OPENED
SYSTEM OUTLINE
SERVICE HINTS

249
1. AIR INLET CONTROL SERVO MOTOR OPERATION (FOR PUSH SW TYPE)
(SWITCHING FROM FRESH TO RECIRC)
WITH THE IGNITION SW ON, CURRENT FROM THE GAUGE FUSE FLOWS TO TERMINAL 1 OF THE SERVO MOTOR. WHEN THE
RECIRC SW IS TURNED ON, THE CURRENT FLOWS FROM SERVO MOTOR " TERMINAL 3 " TERMINAL 5 OF THE HEATER
CONTROL SW " TERMINAL 1 " GROUND, THE MOTOR ROTATES AND THE DAMPER MOVES TO THE RECIRC SIDE. WHEN IT IS IN
THE RECIRC POSITION, THE CIRCUIT IS CUT INSIDE THE SERVO MOTOR AND THE DAMPER STOPS IN THAT POSITION.
WHEN THE CIRCUIT FOR THE INDICATOR LIGHT, CURRENT FLOWS FROM THE GAUGE FUSE " TERMINAL 12 OF THE HEATER
CONTROL SW " INDICATOR LIGHT " TERMINAL 1 " GROUND AND THE INDICATOR LIGHT CONTINUES TO LIGHT UP WHILE THE
RECIRC SW IS ON.
(SWITCHING FROM RECIRC TO FRESH)
WHEN THE IGNITION IS ON AND THE FRESH SW IS TURNED ON, CURRENT FLOWS FROM TERMINAL 2 OF THE SERVO MOTOR "
TERMINAL 6 OF THE HEATER CONTROL SW " TERMINAL 1 " GROUND, THE MOTOR ROTATES AND THE DAMPER MOVES TO THE
FRESH SIDE. WHEN THE DAMPER IS IN THE FRESH POSITION, THE CIRCUIT IS CUT INSIDE THE SERVO MOTOR AND THE DAMPER
STOPS IN THAT POSITION.
2. OPERATION OF AIR VENT MODE CONTROL SERVO MOTOR
WHEN THE IGNITION SW ON, CURRENT FLOWS FROM THE GAUGE FUSE TO TERMINAL 12 OF THE HEATER CONTROL SW,
TERMINAL 6 OF THE AIR VENT MODE CONTROL SERVO MOTOR.
WHEN THE DAMPER IS IN FACE POSITION AND THE BI±LEVEL OF THE HEATER CONTROL SW IS THEN TURNED ON, CURRENT
FLOWS FROM TERMINAL 3 OF THE HEATER CONTROL SW " TERMINAL 4 OF THE AIR VENT MODE CONTROL SERVO MOTOR SO
THAT A SINGAL THAT THE GROUND CIRCUIT IS ACTIVATED IS INPUT TO TERMINAL ªBº OF THE CONTROL CIRCUIT INSIDE THE AIR
VENT MODE CONTROL SERVO MOTOR.
SIMULTANEOUSLY, A SIGNAL THAT THE GROUND CIRCUIT IS NOT ACTIVATED IS INPUT TO TERMINAL ªAº OF THE CONTROL
CIRCUIT INSIDE THE SERVO MOTOR. THESE TWO SIGNALS ACTIVATE THE CONTROL CIRCUIT SO THAT CURRENT FROM THE
GAUGE FUSE TO THE SERVO MOTOR, CAUSING THE SERVO MOTOR TO OPERATE AND THE DAMPER TO MOVE TO BI±LEVEL
POSITION. WHEN THE DAMPER REACHES BI±LEVEL POSITION, A GROUND CUT SIGNAL IS INPUT TO TERMINAL ªBº OF THE
CONTROL CIRCUIT, THE CONTROL CIRCUIT OPERATES, THE SERVO MOTOR STOPS ROTATING AND THE DAMPER STOPS AT
BI±LEVEL.
WHEN ANOTHER MODE POSITION IS SWITCHED TO, INPUT OF SIGNALS TO TERMINAL ªAº AND TERMINAL ªBº OF THE CONTROL
CIRCUIT THAT GROUND IS MADE OR GROUND IS NOT MADE (AS EXPLAINED ABOVE) ACTIAVTES THE CONTROL CIRCUIT AND
MOVES THE SERVO MOTOR TO THE DESIRED POSITION.
3. AIR CONDITIONING OPERATION
WHEN THE IGNITION SW ON, CURRENT FLOWS FROM GAUGE FUSE TO TERMINAL 12 OF THE HEATER CONTROL SW, TERMINAL 6
OF THE AIR VENT MODE CONTROL SERVO MOTOR.
WHEN THE BLOWER SW IS ON, CURRENT FLOWS FROM THE GAUGE FUSE " HEATER RELAY (COIL SIDE) " TERMINAL 7 OF THE
BLOWER SW " TERMINAL 5 " GROUND, ACTIVATING THE HEATER RELAY. THIS CAUSES CURRENT TO FLOW FROM THE HEATER
FUSE TO THE HEATER RELAY (POINT SIDE) " A/C FUSE " TERMINAL 7 OF THE HEATER CONTROL SW (A/C SW). IF THE HEATER
CONTROL (A/C SW) IS THEN TURNED ON AT THIS TIME, A SIGNAL IS INPUT TO THE A/C AMPLIFIRE. THIS ACTIVATES THE A/C
AMPLIFIER AND A/C MAGNETIC CLUTCH RELAY SO THAT CURRENT FLOWS FROM THE GAUGE FUSE TO THE A/C MAGNETIC
CLUTCH RELAY (POINT SIDE) " A/C MAGNETIC CLUTCH, CAUSING THE COMPRESSOR TO OPERATE. THE VSV (FOR A/C IDLE±UP)
IS TURNED ON SIMULTANEOUSLY TO PREVENT A DECREASE IN ENGINE SPEED DUE TO A/C OPERATION.
HEATER RELAY
(4)5± (4)4 : CLOSED WITH THE IGNITION SW ON AND BLOWER SW ON
A/C MAGNETIC CLUTCH RELAY
(4)5± (4)3 : CLOSED WITH THE IGNITION SW ON AND BLOWER SW ON AND A/C SW ON
A 2 A/C DUAL PRESSURE SW
1±4 : OPEN WITH PRESSURE 2.1 KG/CM (30 PSI, 206 KPA) OR ABOVE 27 KG/CM (384 PSI, 2646 KPA)
B 5 BLOWER RESISTOR
6±2 : APPROX. 1.12 W
2±3 : APPROX. 0.5 W
3±1 : APPROX. 0.2 W
SYSTEM OUTLINE
SERVICE HINTS