TOYOTA CAMRY 2000 Service Repair Manual

AUTOMATIC TRANSAXLEPREPARATION ±
AX±8
PREPARATION
SST (SPECIAL SERVICE TOOLS)
09240±00020Wire Gauge Set
09330±00021Companion Flange Holding Tool
09350±32014TOYOTA Automatic Transmission
Tool Set
09308±10010Oil Seal Puller
(09351±32020)Stator Stopper
(09351±32032)Counter Driven Gear Holding Tool
(09351±32040)No.1 Piston Spring Compressor
(09351±32050)Snap Ring Expander
(09351±32061)Oil Pump Puller
(09351±32070)No.2 Piston Spring Compressor
(09351±32080)Lock Nut Wrench
(09351±32090)Oil Seal Remover & Replacer
(09351±32100)Drive Pinion Bearing Replacer
AX0EQ±02

AUTOMATIC TRANSAXLEPREPARATION ±
AX±9
(09351±32111)Side Bearing Race Replacer
(09351±32120)Overdrive Bearing Replacer
(09351±32130)Handle
(09351±32140)Oil Seal Replacer
(09351±32150)Oil Seal Replacer
(09351±32190)Measure Terminal
(09351±32200)No.3 Piston Spring Compressor
09502±10012Differential Side Bearing Puller


09564±32011Differential Preload Adaptor
09710±28020Front Suspension Bushing Tool
Set

(09710±08040)Bushing Replacer

09950±00020Bearing Remover
RECOMMENDED TOOL
09031±00030Pin Punch .
AX0ER±02

AUTOMATIC TRANSAXLEPREPARATION ±
AX±10
EQUIPMENT
Feeler gauge
Vernier calipers
Dial indicator or dial indicator with magnetic base
Straight edge
Torque wrench
LUBRICANT
ItemLiters
US qts Imp qtsClacification
Automatic Transaxle Fluid
(w/o Differential Fluid) Dry Fill
Drain and Refill5.6
5.9 4.9
2.5
2.6 2.2
ATF DEXRON ® @@@@@: [g 2]
Differential Fluid1.6
1.7 1.4ATF DEXRON ® @@@@@: [g 2]
SSM (SPECIAL SERVICE MATERIALS)
08826±00090Seal Packing 1281,
THREE BOND 1281 or equivalent
(FIPG)
08833±00070Adhesive 1324,
THREE BOND 1324 or equivalent
AX0ES±02
AX0ET±02
AX0EU±02

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±11
COMPONENT PARTS REMOVAL
COMPONENTS
AX0GS±02

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±12

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±13

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±14

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±15
SEPARATE BASIC SUBASSEMBLY
1. REMOVE PARK/NEUTRAL POSITION SWITCH
(a) Remove the manual shift lever.
(b) Pry off the lock washer and remove the manual valve
shaft nut.
(c) Remove the 2 bolts and pull out the park/neutral position
switch.
2. REMOVE UNION AND ELBOW
(a) Using the open end wrench, remove the union and elbow.
(b) Remove the O±rings from the union and elbow.
3. REMOVE SL SOLENOID
(a) Disconnect the connector.
(b) Remove the 2 bolts and SL solenoid.
4. REMOVE THROTTLE CABLE RETAINING PLATE
5. REMOVE SOLENOID WIRE RETAINING BOLT
6. REMOVE COVER
(a) Remove the 2 bolts and cover bracket.
AX0EW±02

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±16
(b) Remove the cover.
7. REMOVE OIL PAN AND GASKET
(a) Remove the 15 bolts.
(b) Remove the oil pan by lifting transaxle case.
NOTICE: Do not turn the transaxle over as this will contami-
nate the valve body with the foreign materials in the bottom
of the oil pan.
(c) Place the transaxle on wooden blocks to prevent damage
to the tube bracket.
8. EXAMINE PARTICLES IN PAN
Remove the magnets and use them to collect any steel
chips. Look carefully at the chips and particles in the oil
pan and on the magnets to anticipate what type of wear
you will find in the transmission:
Steel (magnetic): bearing, gear and plate wear
Brass (non±magnetic): bushing wear
9. DISCONNECT NO.1 AND NO.2 SOLENOID CONNEC-
TORS
10. REMOVE TUBE BRACKET AND OIL STRAINER

AUTOMATIC TRANSAXLECOMPONENT PARTS REMOVAL ±
AX±17
11. REMOVE OIL TUBES
Pry up both tube ends with a large screwdriver and re-
move the 4 tubes.
12. REMOVE MANUAL DETENT SPRING
13. REMOVE MANUAL VALVE AND MANUAL VALVE
BODY
14. REMOVE VALVE BODY
(a) Remove the 12 bolts.
15. REMOVE THROTTLE CABLE AND SOLENOID WIR-
ING FROM CASE
16. REMOVE SECOND BRAKE APPLY GASKET