sensor TOYOTA CAMRY 2000 Service Repair Manual

RS05T±01
RS±60
± SUPPLEMENTAL RESTRAINT SYSTEMAIRBAG SENSOR ASSEMBLY
2205 Author: Date:
INSPECTION
1. VEHICLE NOT INVOLVED IN COLLISION
Do a diagnostic system check. (See page DI±626)
2. VEHICLE INVOLVED IN COLLISION AND AIRBAG IS NOT DEPLOYED
Do a diagnostic system check. (See page DI±626)
3. VEHICLE INVOLVED IN COLLISION AND AIRBAG IS DEPLOYED
Replace the airbag sensor assembly. (See page RS±59)

RS01J±13
± SUPPLEMENTAL RESTRAINT SYSTEMAIRBAG SENSOR ASSEMBLY
RS±61
2206 Author: Date:
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the airbag sensor assembly.

If the SRS has been deployed in a collision.

If the airbag sensor assembly has been found to be faulty in troubleshooting.

If the airbag sensor assembly has been dropped.
CAUTION:
For removal and installation of the airbag sensor assembly, see page RS±59 and RS±62. Be sure to
follow the correct procedure.

RS0EZ±01
H02267H02268H08322
LH side:
RH side: RS±62
± SUPPLEMENTAL RESTRAINT SYSTEMAIRBAG SENSOR ASSEMBLY
2207 Author: Date:
INSTALLATION
NOTICE:

Never use SRS parts from another vehicle. When re-
placing parts, replace them with new parts.

Never reuse the airbag sensor assembly involved in
a collision when the airbag has deployed.

Never repair a sensor in order to reuse it.
INSTALL AIRBAG SENSOR ASSEMBLY
(a) Using a torx wrench, install the airbag sensor assembly
with 4 screws.
Torx wrench: T40 (Part No.09042±00020 or locally
manufactured tool)
Torque: 20 N´m (205 kgf´cm, 15 ft´lbf)
(b) Connect the airbag sensor connectors.
NOTICE:

Connection of the connector is done after the sensor
assembly has been installed.

Make sure the sensor assembly is installed with the
specified torque.

If the sensor assembly has been dropped, or there are
cracks, dents or other defects in the case, bracket or
connector, replace the sensor assembly with a new
one.

When installing the sensor assembly, take care that
the SRS wiring does not interfere with other parts and
is not pinched between other parts.

After installing , shake the sensor assembly to check
that there is no looseness.

RS01L±14
H08233
N´m (kgf´cm, ft´lbf) : Specified torqueFront Airbag Sensor (RH)Front Airbag Sensor (LH)
20 (205, 15)
20 (205, 15)
20 (205, 15)
Turn Signal Light RH
Turn Signal Light LH
Head Light RH
Head Light LH
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
RS±63
2208 Author: Date:
FRONT AIRBAG SENSOR
COMPONENTS

RS0F0±01
H08318
H08319
RS±64
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
2209 Author: Date:
REMOVAL
NOTICE:

If the wiring connector of the SRS is disconnected
with the ignition switch at ON or ACC position, DTCs
will be recorded.

Never use SRS parts from another vehicle. When re-
placing parts, replace them with new parts.

Never reuse the sensor involved in a collision when
the SRS has deployed.

Never repair a sensor in order to reuse it.
1. REMOVE HEAD LIGHT LH AND RH
(a) Remove the 2 clips and turn signal lights.
(b) Remove the 4 bolts and head lights.
2. LH:
REMOVE FRONT AIRBAG SENSOR
(a) Disconnect the connector.
NOTICE:
Disconnect the connector with sensor assembly installed.
(b) Remove the 2 bolts and front airbag sensor LH.
3. RH:
REMOVE FRONT AIRBAG SENSOR
(a) Disconnect the connector.
NOTICE:
Disconnect the connector with sensor assembly installed.
(b) Remove the 2 bolts and front airbag sensor RH.

RS01N±16
H08235
H06728
LH:
RH:
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
RS±65
2210 Author: Date:
INSPECTION
1. VEHICLE NOT INVOLVED IN COLLISION
Do a diagnostic system check.
(See page DI±626)
2. VEHICLE INVOLVED IN COLLISION
(a) Do a diagnostic system check.
(See page DI±626)
(b) If the front fender of the car or its periphery is damaged,
do a visual check for damage to the front airbag sensor,
which includes the following items even if the airbag was
not deployed:

Bracket deformation

Paint peeling off the bracket

Cracks, dents or chips in the case

Cracks, dents, chipping and scratches in the con-
nector

Peeling off of the label or damage to the serial num-
ber

RS01O±10
RS±66
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
2211 Author: Date:
REPLACEMENT
REPLACEMENT REQUIREMENTS
In the following cases, replace the front airbag sensor.

If the SRS has been deployed in a collision. (Replace both the left and right airbag sensors.)

If the front airbag sensor has been found to be faulty in troubleshooting.

If the front airbag sensor has been found to be faulty during checking items.
(See page RS±65)

If the front airbag sensor has been dropped.
CAUTION:
For removal and installation of the front airbag sensor, see page RS±64 and RS±67. Be sure to follow
the correct procedure.

RS01P±14
H06728
LH:
RH:
± SUPPLEMENTAL RESTRAINT SYSTEMFRONT AIRBAG SENSOR
RS±67
2212 Author: Date:
INSTALLATION
1. INSTALL FRONT AIRBAG SENSOR LH AND RH
(a) Install the front airbag sensor with the arrow on the sensor
facing toward the front of the vehicle.
Torque: 20 N´m (205 kgf´cm, 15 ft´lbf)
NOTICE:

Connection of the connector is done after the sensor
assembly has been installed.

Make sure the sensor is installed with the specified
torque.

If the sensor has been dropped, or there are cracks,
dents or other defects in the case, brackets or con-
nector, replace the removed sensor with a new one.

The front sensor is equipped with an electrical con-
nection check mechanism. Be sure to lock this mech-
anism securely when connecting the connector. If the
connector is not securely locked, a malfunction code
will be detected by the diagnostic system.
(b) Connect the front airbag sensor connector.
2. INSTALL HEAD LIGHT LH AND RH
(See page BE±28)
3. INSTALL TURN SIGNAL LIGHT LH AND RH

RS01Q±06
H03285: Specified torqueN´m (kgf´cm, ft´lbf)
Side Airbag Sensor Assembly
20 (205, 15)
Front Seat Outer Belt Retractor
42 (430, 31)
Center Pillar Lower Garnish
Front Door Scuff Plate
7.5 (76, 66 in.´lbf)
RS±68
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG SENSOR ASSEMBLY
2213 Author: Date:
SIDE AIRBAG SENSOR ASSEMBLY
COMPONENTS

RS01R±05
H01346
H01339
± SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG SENSOR ASSEMBLY
RS±69
2214 Author: Date:
REMOVAL
NOTICE:
Do not open the cover or the case of the ECU and various
electrical devices unless absolutely necessary.
(If the IC terminals are touched, the IC may be destroyed by
static electricity.)
1. REMOVE FRONT DOOR SCUFF PLATE
2. REMOVE CENTER PILLAR LOWER GARNISH
3. REMOVE FRONT SEAT OUTER BELT RETRACTOR
(See page BO±126)
(a) Disconnect the pretensioner connector.
(b) Remove the 2 bolts and retractor.
4. REMOVE SIDE AIRBAG SENSOR ASSEMBLY
(a) Disconnect the side airbag sensor assembly connector.
NOTICE:
Disconnect the connector with the sensor assembly
installed.
(b) Using a torx wrench, remove the 3 screws and side airbag
sensor assembly.
Torx wrench: T40 (Part No.09042±00020 or locally
manufactured tool)