hood TOYOTA CAMRY 2000 Service Repair Manual

3
CAMRY ± OUTLINE OF NEW FEATURES27
8. Brakes
The specifications of the front and rear brakes have been changed.
9. Suspension
The front and rear springs, stabilizers, and shock absorbers have been modified to realize excellent stability,
controllability, and riding comfort.
10. Steering
A check valve has been added to the power steering gear box to help reduce kickback.
The rack stroke of the 5S-FE engine model has been changed to 145mm (5.71 in.), which is the same as
in the 1MZ-FE engine.
11. Body
Hood support dampers are used.
Two utility hooks added in the luggage room for the gasoline engine model.
To install the fuel tank in the front area of the luggage compartment, the upper back panel has been cut
out for the 5S-FNE engine model.
A performance rod that joins the tops of the right and left rear suspension strut towers has been adopted
for the 5S-FNE engine model.
The shape of the rear floor pan has been changed to prevent the luggage compartment capacity from being
reduced as a result of the installation of the fuel tank in the luggage compartment for the 5S-FNE engine
model.
12. Seat
The seat cover of the LE grade model has been changed.
Optional driver power seat added for the LE grade model.
A fixed type seat back is used for the rear seat for the 5S-FNE engine model.
13. Seat Belt
2-point NR (Non-Retractor) seat belt is used for the rear center seat for the 5S-FNE engine model.
14. Wireless Door Lock Control
Audio answer back is adopted.
15. Lighting
Along with the adoption of the 4-beam headlights, the electrical circuit of the daytime running light system
has been changed.
16. Air Conditioning
The air inlet mode selector of heater control panel has been changed from the lever type to the push button
type on the CE and LE grade model.
When the air outlet mode is set to the DEF or FOOT / DEF mode, the air inlet mode also changes to the
FRESH mode, has been also added on the CE and LE grade model.
A fully automatic controlled type air conditioning is used on the XLE grade model.
A defroster-linked air conditioning start up control has been continuing to use since the previous models
with air conditioning.
17. SRS Airbag
The inflator of the SRS airbag for the driver has been made more compact and lightweight.
A signal that causes the supply of fuel to be cut off during a frontal collision is output by the airbag sensor
assembly to the ECM for the 5S-FNE engine model.

CAMRY ± NEW FEATURES
172CM08
Hood Support Dampers
Utility Hooks
172CM09
High
High Beam
Indicator Light
Low
HighLow
Daytime
Running
Light
Relay No.3
Daytime Running Light
Relay No.4
'00 Model
HighLowHighLow
Daytime Running
Light Relay No.4Daytime Running
Light Resistor
'99 Model 58
Hood support dampers are used.
Two utility hooks added in the luggage room.
LIGHTING
The 4-light multi-reflector type headlights are adopted with new styling.
Along with the adoption of the 4-beam headlights, the daytime running light system has been changed
from the '99 model type that uses resistors to dim the low beams. On the 2000 model, the daytime running
light is a type that dims the right and left high beams through a series circuit.

ENGINE REMOVAL
1. DISCONNECT NEGATIVE (±) TERMINAL CABLE
FROM BATTERY
CAUTION: Work must be started after 90 seconds from
the time the ignition switch is turned to the 'LOCK'
position and the negative (±) terminal cable Is discon±
nected from the battery.
2. REMOVE BATTERY AND TRAY
3. REMOVE HOOD
4. REMOVE ENGINE UNDER COVER
5. DRAIN ENGINE COOLANT
6. DRAIN ENGINE OIL
7. DISCONNECT ACCELERATOR CABLE FROM
THROTTLE BODY
8. A/T:
DISCONNECT THROTTLE CABLE FROM
THROTTLE BODY
9. REMOVE AIR CLEANER ASSEMBLY, RESONATOR
AND AIR CLEANER HOSE
(a) Disconnect the intake air temperature sensor connec±
tor.
(b) California only:
Disconnect the air hose from the air cleaner hose.
(c) Loosen the air cleaner hose clamp bolt.
(d) Disconnect the 4 air cleaner cap clips.
(e) Disconnect the air cleaner hose from the throttle
body, and remove the air cleaner cap together with
the resonator and air cleaner hose.
(f) Remove the element.
(g) Remove the 3 bolts and air cleaner case.
10. w/ CRUISE CONTROL SYSTEM:
REMOVE CRUISE CONTROL ACTUATOR
(a) Remove the actuator cover.
(b) Disconnect the actuator connector.
(c) Remove the 3 bolts, and disconnect the actuator with
the bracket.
11. REMOVE RADIATOR
± 5S±FE ENGINEENGINE MECHANICALEG1±85

27. INSTALL AIR CLEANER ASSEMBLY, RESONATOR
AND AIR CLEANER HOSE
(a) Install the air cleaner case with 3 bolts.
(b) Install the element.
(c) Connect the air cleaner hose to the throttle body.
(d) Install the air cleaner cap together with the resonator
and air cleaner hose.
(e) California only:
Connect the air hose to the air cleaner hose.
(f) Connect the intake air temperature sensor connector.
28. A/T:
CONNECT AND ADJUST THROTTLE CABLE
29. CONNECT AND ADJUST ACCELERATOR CABLE
30. FILL WITH ENGINE COOLANT
31. FILL WITH ENGINE OIL
32. CONNECT NEGATIVE (±) TERMINAL CABLE TO
BATTERY
33. START ENGINE AND CHECK FOR LEAKS
34. PREFORM ENGINE ADJUSTMENT
35. INSTALL ENGINE UNDER COVERS
36. INSTALL HOOD
37. PERFORM ROAD TEST
Check for abnormal noises, shock, slippage, correct
shift points and smooth operation.
38. RECHECK ENGINE COOLANT AND ENGINE OIL
LEVELS26. w/ CRUISE CONTROL SYSTEM:
INSTALL CRUISE CONTROL ACTUATOR
(a) Install the actuator and bracket with the 3 bolts.
(b) Connect the actuator connector.
(c) Install the actuator cover.(6) Data link connector 1
(7) 2 ground straps from RH fender apron
(e) Connect the MAP sensor connector.
25. INSTALL RADIATOR
± 5S±FE ENGINEENGINE MECHANICALEG1±133

1. DISCONNECT NEGATIVE (±) TERMINAL CABLE
FROM BATTERY
CAUTION: Work must be started after 90 seconds from
the time the ignition switch is turned to the ªLOCKº
position and the negative (±) terminal cable is discon±
nected from the battery.
2. REMOVE HOOD
3. DRAIN ENGINE OIL (See page EG1±274)
OIL PUMP REMOVAL
HINT: When repairing the oil pump, the oil pan and
strainer should be removed and cleaned.
OIL PUMP
COMPONENTS FOR REMOVAL AND
INSTALLATION
± 5S±FE ENGINELUBRICATION SYSTEMEG1±276

10. INSTALL FRONT EXHAUST PIPE
(a) Place 2 new gaskets on the front and rear of the front
exhaust pipe.
(b) Temporarily install the 2 bolts and 2 new nuts holding
front exhaust pipe to the center exhaust pipe.
(c) Using a 14 mm deep socket wrench, install the 3 new
nuts holding the front exhaust pipe to the WU±TWC.
Torque: 62 N±m (630 kgf±cm, 46 ft±lbf)
(d) Tighten the 2 bolts and 2 nuts holding front exhaust
pipe to the center exhaust pipe.
Torque: 56 N±m (570 kgf±cm, 41 ft±lbf)
(e) Install the bracket with the 2 bolts.
11. CONNECT NEGATIVE (±) TERMINAL CABLE TO
BATTERY
12. FILL WITH ENGINE OIL (See page EG1±275)
13. START ENGINE AND CHECK FOR LEAKS
14. RECHECK ENGINE OIL LEVEL
15. INSTALL HOOD (c) Install the oil pan with 17 bolts and 4 nuts.
Torque: 5.4 N±m (55 kgf±cm, 48 in.±lbf)
(d) Install the dipstick.
9. INSTALL STIFFENER PLATE
Install the stiffener plate with the 3 bolts.
Torque: 37 N±m (380 kgf±cm, 27 ft±Ibf)
± 5S±FE ENGINELUBRICATION SYSTEMEG1±285

19
INTERIOR
INSTRUMENT PANEL, SWITCH LAYOUT AND EQUIPMENT
While maintaining continuity with the door trims and the console, the instrument panel provides a form with a
lowered center of gravity to emphasize a sense of freedom.
The unique, compact meter hood expresses a sense of sportiness.
The frequently used audio system has been located above the heater control panel, thus improving its ease of use.

23
INTERIOR
 WIRELESS DOOR LOCK REMOTE CONTROL SYSTEM
A wireless door lock remote control system is available as an option on the LE grade model and is standard
equipment on the XLE grade model. With the wireless door lock remote control system, all the doors can be locked
and unlocked by signals emitted by the transmitter.
A 2±step unlock function is provided. When the unlock switch of the transmitter is pressed once, only the driver's
door is unlocked. When it is pressed twice, all the doors are unlocked.
A panic switch is provided in the transmitter to force the theft system by operating the horn, headlight and taillight.
A wireless door lock ECU with EEPROM (Electrical Erasable Programmable ROM) is used so that the transmitter
recognition code can be easily reprogrammed.
 THEFT DETERRENT SYSTEM
A theft deterrent system is used to prevent vehicle theft. When the system is set, the horn and headlights operate
if the door, hood or trunk is forcibly opened.
The audio system also has an anti±theft system whereby the radio and cassette deck is disabled if the radio body
is stolen from the vehicle.

89BODYÐLIGHTWEIGHT AND HIGHLY RIGID BODY
BODY
LIGHTWEIGHT AND HIGHLY RIGID BODY
The body of the new Camry is made highly rigid and lightweight through refinement of the shap and construction
of each part, improved joint rigidity, and increased use of high strength sheet steel.
 HIGH STRENGTH SHEET STEEL
Light and highly rigid high strength sheet steel is used for the hood, door panels and members.

94BODYÐRUST±RESISTANT BODY
RUST±RESISTANT BODY
Rust±resistant performance is enhanced by extensive use of anti±corrosion sheet steel and is performing and
anti±corrosion treatment by applying wax, sealer and anti±chipping paint to easily corroded parts such as the hood,
doors and rocker panels.

ANTI±CORROSION SHEET STEEL
Galvannealed sheet steel is used in all areas other than the interior parts and the roof. However, on models produced
by TMC, zinc±iron alloy double layer galvannealed sheet steel is used for quarter panel.