load capacity TOYOTA CAMRY 2000 Service Repair Manual

3
CAMRY ± NEW FEATURES
167CN05
WU-TWC
167CN06
TWCSub MufflerMain Muffler41
5. Intake and Exhaust System
Throttle Body
The throttle body is basically the same as that of the 5S-FE engine. However, to ensure the starting perfor-
mance at low temperatures, the air passage for the IAC (Idle Air Control) has been increased on the 5S-FNE
engine. The IAC valve is a 1-coil type with a built-in driver.
Exhaust Manifold
As in the California specification 5S-FE engine,
the stainless steel exhaust manifold and WU-
TWC (Warm Up Three-Way Catalytic Convert-
er) have been integrated to improve the warm-up
performance of TWC, thus reducing exhaust
emissions.
However, the 5S-FNE engine uses a catalytic
converter that has been designed exclusively for
the CNG application, in which the loading of the
noble metal has been increased.
Exhaust Pipe
1) General
To secure sufficient luggage compartment capacity, the main muffler has been relocated below the rear
seat. Furthermore, the muffler capacity has been increased.
A 2-way exhaust control system has been adopted to improve engine performance and reduce the exhaust
noise.
Similar to the WU-TWC, the TWC (Three-Way Catalytic Converter) has been designed exclusively for
the CNG application, in which the loading of the noble metal has been increased.

'99camry U
222

Take special care when adding air to
the compact spare tire. The smaller
tire size can gain pressure very quick-
ly. Add compressed air in small quanti-
ties and check the pressure often until
it reaches the specified pressure.

Do not bleed or reduce tire pressure
after driving. It is normal for the tire
pressure to be higher after driving.

Never exceed the vehicle capacity
weight. The passenger and luggage
weight should be located so that the
vehicle is balanced.

Be sure to reinstall the tire inflation
valve caps. Without the valve caps,
dirt or moisture could get into the valve
core and cause air leakage. If the caps
have been lost, have new ones put on
as soon as possible.
Checking and replacing tires
Tread wear indicator
CHECKING YOUR TIRES
Check the tires tread for the tread wear
indicators. If the indicators show, re-
place the tires.
The tires on your Toyota have built±in
tread wear indicators to help you know
when the tires need replacement. When
the tread depth wears to 1.6 mm (0.06
in.) or less, the indicators will appear. If
you can see the indicators in two or more
adjacent grooves, the tire should be re-
placed. The lower the tread, the higher
the risk of skidding.
The effectiveness of snow tires is lost
if the tread wears down below 4 mm
(0.16 in.).Check the tires regularly for damage
such as cuts, splits and cracks. If any
damage is found, consult with a techni-
cian and have the tire repaired or re-
placed.
Even if the damage does not appear seri-
ous, a qualified technician should examine
the damage. Objects which have pene-
trated the tire may have caused internal
damage.
Any tires which are over six years old
must be checked by a qualified techni-
cian even if damage is not obvious.
Tires deteriorate with age even if they
have never or seldom been used.
This applies also to the spare tire and
tires stored for future use.
REPLACING YOUR TIRES
When replacing a tire, use only the
same size and construction as original-
ly installed and with the same or great-
er load capacity.
Using any other size or type of tire may
seriously affect handling, ride, speedome-
ter/odometer calibration, ground clearance,
and clearance between the body and tires
or snow chains.

'99camry U
223
CAUTION

Do not mix radial, bias belted, or
bias±ply tires on your vehicle. It
can cause dangerous handling char-
acteristics, resulting in loss of con-
trol.

Do not use tires or wheels other
than the manufacturer 's recom-
mended size.
Toyota recommends all four tires, or at
least both of the front or rear tires be
replaced at a time as a set.
See ºIf you have a flat tireº in Part 4 for
tire change procedure.
When a tire is replaced, the wheel
should always be balanced.
An unbalanced wheel may affect vehicle
handling and tire life. Wheels can get out
of balance with regular use and should
therefore be balanced occasionally.
When replacing a tubeless tire, the air
valve should also be replaced with a
new one.
Rotating tires
To equalize the wear and help extend
tire life, Toyota recommends that you
rotate your tires approximately every
12000 km (7500 miles). However, the
most appropriate timing for tire rotation
may vary according to your driving hab-
its and road surface conditions.
See ºIf you have a flat tireº in Part 4 for
tire change procedure.
When rotating tires, check for uneven
wear and damage. Abnormal wear is usu-
ally caused by incorrect tire pressure, im-
proper wheel alignment, out±of±balance
wheels, or severe braking.WHEN TO USE SNOW TIRES OR
CHAINS
Snow tires or chains are recommended
when driving on snow or ice.
On wet or dry roads, conventional tires
provide better traction than snow tires.
SNOW TIRE SELECTION
If you need snow tires, select the same
size, construction and load capacity as
the original tires on your Toyota.
Do not use tires other than those men-
tioned above. Do not install studded tires
without first checking local regulations for
possible restrictions.
SNOW TIRE INSTALLATION
Snow tires should be installed on all
wheels.
Installing snow tires on the front wheels
only can lead to an excessive difference
in road grip capability between the front
and rear tires which could cause loss of
vehicle control.
When storing removed tires you should
store them in a cool dry place. Mark the
direction of rotation and be sure to install
them in the same direction when replac-
ing.
Installing snow tires and
chains

'99camry U
166

Never allow anyone to ride in the
enlarged trunk. It is not designed
for passengers. They should ride in
their seats with their seat belts
properly fastened. Otherwise, they
are much more likely to suffer seri-
ous bodily injury, in the event of
sudden braking or a collision.

Do not place anything on the filler
panel behind the rear seatback.
Such items may be thrown about
and possibly injure people in the
vehicle during sudden braking or an
accident.

Do not drive with objects left on
top of the instrument panel. They
may interfere with the driver's field
of view. Or they may move during
sharp vehicle acceleration or turn-
ing, and impair the driver's control
of the vehicle. In an accident they
may injure the vehicle occupants.
NOTICE
Do not load the vehicle beyond the
vehicle capacity weight specified in
Part 8.
The vehicle identification number (VIN)
is the legal identifier for your vehicle.
This number is on the left top of the
instrument panel, and can be seen
through the windshield from outside.
This is the primary identification number
for your Toyota. It is used in registering
the ownership of your vehicle.The vehicle identification number (VIN) is
also on the Certification Label.
Your Toyota's identificationÐ
ÐVehicle identification
number

NF
NEW FEATURES Ð 5S-FNE ENGINE11
INTAKE AND EXHAUST SYSTEM
1. Throttle Body
The throttle body is basically the same as that of the 5S-FE engine. However, to ensure the starting perfor-
mance at low temperatures, the air passage for the IAC (Idle Air Control) has been increased on the 5S-FNE
engine. The IAC valve is a 1-coil type with a built-in driver.
2. Exhaust Manifold
As in the California specification 5S-FE engine,
the stainless steel exhaust manifold and WU-TWC
(Warm Up Three-Way Catalytic Converter) have
been integrated to improve the warm-up perfor-
mance of TWC, thus reducing exhaust emissions.
However, the 5S-FNE engine uses a catalytic con-
verter that has been designed exclusively for the
CNG application, in which the loading of the noble
metal has been increased.
3. Exhaust Pipe
General
To secure sufficient luggage compartment capacity, the main muffler has been relocated below the rear
seat. Furthermore, the muffler capacity has been increased.
A 2-way exhaust control system has been adopted to improve engine performance and reduce
the exhaust noise.
Similar to the WU-TWC, the TWC (Three-Way Catalytic Converter) has been designed exclusively for
the CNG application, in which the loading of the noble metal has been increased.
Main Muffler
167CN06TWCSub Muffler
p12WU-TWC
167CN05