ignition TOYOTA CAMRY HYBRID 2020 Owners Manual (in English)

5
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURESBrake system warning1Malfunction/
Check Engine indicator1
Low Tire Pressure Warning1
Low fuel level warning
Security indicator
Fuel tank door position
READY indicator
Master warning
1,2
Headlight low/high beam
indicators
Turn signal indicator
Pre-Collision System (PCS)
warning light1,2
Lane Departure Alert (LDA) indicator
(white/green/yellow3 indicator)
Slip indicator1,3
Vehicle Stability Control OFF indicator1
Parking brake indicator2
Electric power steering warning1
(red/yellow indicator)
Rear passenger seat belt reminder
indicator Type A
Rear passenger seat belt reminder
indicator Type B
Electric brake hold operated indicator1,2
Electric brake hold standby indicator1
BSM w/Rear Cross Traffic Alert (RCTA)
Indicator4
BSM outside rear view mirror
indicators4
Sport mode driving indicator
ECO MODE indicator
EV drive mode indicator
EV indicator
Low outside temperature indicator
Brake system warning
(yellow indicator)1
Full-Speed Dynamic Radar Cruise
Control (DRCC) indicator/DRCC
SET indicator
Constant speed cruise control
indicator/Constant speed
cruise control SET indicator
Driver’s and
front passenger’s seat belt
reminder (alarm will sound when the
engine switch is in the “IGNITION ON”
mode)
1 If the indicator does not turn off within a few seconds of starting the \
Hybrid System, there may be a
malfunction. Have the vehicle inspected by your Toyota dealer.
2 If the indicator flashes, there may be a malfunction. Refer to the Owner\
’s Manual.3 If the indicator flashes, it indicates that the system is operating.4 If equipped.

10
Hybrid transmission
Auto lock/unlock
FEATURES & OPERATIONS
Automatic door locks can be programmed to operate in different modes, or\
turned
OFF.
Shift position linked door locking/unlocking function
-Doors lock when shifting from Park.
-Doors unlock when shifting into Park.
Speed linked door locking function
-Doors lock when the vehicle speed goes above approximately 12 mph (20 km/h).
Driver’s door linked door unlocking function
-Doors unlock when the engine switch is set to OFF and driver’s door i\
s opened.
Refer to the Owner’s Manual for more details.
Shift the shift lever to “S” position from “D” position.Downshifting increases power going uphill, or provides engine braking do\
wnhill. For
best fuel economy during normal driving conditions, always drive with th\
e shift lever
in the “D” position. * The “POWER” switch must be in the “IGNITION ON” mode and t\
he brake pedal depressed to shift from Park.
“S” (SEQUENTIAL) MODE
+ (“S” mode)
Shift lever
Paddle shifters*
*If equipped
- (“S” mode)
- (“S” mode)
+ (“S” mode)
N
Park*
Reverse
Neutral
Drive
“S” mode
Shift lever type:
+ : Upshift (push and release)
- : Downshift (pull and release) Paddle shifters type (if equipped):
+ : Upshift (pull and release)
- : Downshift (pull and release)

22
FEATURES & OPERATIONS
Power outlet-12V DC
The engine switch must be in the “ACCESSORY” or “IGNITION ON” mode for use.
USB media port
Open lid
Connecting a compatible device and cable into the USB media port will su\
pport
charging and music playback through the audio multimedia system.
USB charge-ports
The engine switch must be in the “ACCESSORY” or “IGNITION ON” mode for use.
(Charge only)

26
FEATURES & OPERATIONS
CUP HOLDERS
FrontRear
Bottle holders/Cup holders
Front
Qi Wireless Charging (if equipped)
Rear
Power switchCharge areaOperation indicator light
A mobile device can be charged wirelessly on the tray. (1) Press the wireless
charger power switch and the green operation indicator light turns on. (2) Place
a compatible mobile device on the tray as shown in the illustration. An \
amber
indicator illuminates while charging is in progress. When charging is co\
mplete, the
indicator illuminates green. Some phones, cases or cover type wireless c\
hargers
may not cause the green indicator to illuminate even though it is fully \
charged.
The engine switch must be in the “ACCESSORY” or ”IGNITION ON” mode for use.
Refer to the Owner’s Manual for limitations and more details on this \
system before
attempting to use it.
Press (1)
When the engine is turned off, the last state
(ON/OFF) of the charger is memorized.
Place (2)
BOTTLE HOLDERS (DOOR MOUNTED)

30
TOYOTA SAFETY SENSE™
CHANGING PCS ALERT TIMING
FarMiddle
(default) Near
Monocular camera sensor
Millimeter
wave radar
As part of the Pre-Collision System, this function is also designed to f\
irst provide an
alert and then automatic braking if needed.
Refer to the Toyota Owner’s Manual for additional limitations and inf\
ormation.Under certain conditions, the PCS system included with the TSS-P package\
may
also help to detect a pedestrian in front of your vehicle using the in-v\
ehicle camera
and front grille-mounted radar. The in-vehicle camera of PCS detects a p\
otential
pedestrian based on size, profile, and motion of the detected pedestrian\
. However,
a pedestrian may not be detected depending on the conditions, including \
the
surrounding brightness and the motion, posture, size, and angle of the p\
otential
detected pedestrian, preventing the system from operating or engaging.
PCS PEDESTRIAN DETECTION
(1) Press “” switches and select or from the Multi-Information
Display (MID).
(2) Press “
” switches and select “Warning sensitivity” from the MID and th\
en
press “
”. The setting screen is displayed.
(3) Press “
” each time to change the setting. Each time it is pressed, the
response to the PCS alert timing changes as shown above. You can press “
” to
go back to the menu.
Note: PCS is enabled each time the engine switch is turned to Ignition On.
The system can be disabled/enabled and the alert timing of the system can be
changed. (Alert timing only, brake operation remains the same).

32
TOYOTA SAFETY SENSE™
TURNING THE LDA SYSTEM ON/OFF
Press the LDA switch to turn the LDA system on. Depress again to turn it\
off.
Note: Operation of the LDA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.
Refer to the Toyota Owner’s Manual for additional information on LDA \
operation,
settings adjustments, limitations, and precautions before attempting to \
use it.
LANE DEPARTURE ALERT
LDA function display
Steering assist indicatorLDA indicatorLane markers
(2)
(1)
Lane Departure Alert (LDA) indicator flashes orange when operating.

33
The LDA function
displays when the Multi-Information Display (MID) is switched
to the driving assist system information screen.
(1) The system displays solid white lines on the LDA indicator when visible lane
markers on the road are detected. A side flashes orange to alert the dri\
ver when the
vehicle deviates from its lane.
(2) The system displays outlines on the LDA indicator when lane markers on the road
are not detected or the function is temporarily cancelled.
Note: When operation conditions are no longer met, a function may be
temporarily canceled. However, when the operation conditions are met again,
operation of the function is automatically restored. For example, LDA may not
function on the side(s) where white/yellow lines are not detectable.
Refer to the Toyota Owner’s Manual for additional information on LDA \
operation,
settings adjustments, limitations, and precautions before attempting to \
use it.
ADJUSTING LDA ALERT SENSITIVITY
DISABLING STEERING ASSIST
The driver can adjust the sensitivity of the LDA (warning) function from the
Multi-Information Display (MID) customization screen.
High - Is designed to warn approximately before the front
tire crosses the lane marker.
Normal - Is designed to warn approximately when the front
tire crosses the lane marker.
LANE DEPARTURE ALERT (CONTINUED)
(1) Press “” switches and select or from the Multi-Information
Display (MID).
(2) Press “
” switches and select the “Steering Assist” setting function an\
d then
press “
.”
(3) Press “
” each time to change the setting.
(4) Press “
” to go back to the menu.
Note: Operation of the LDA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.
(1) Press “
” switches and select or from the Multi-Information Display
(MID).
(2) Press “
” switches and select the “Alert sensitivity” setting function \
and then
press “
.”
(3) Press “
” each time to change the setting.
(4) Press “
” to go back to the menu.
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES

34
TOYOTA SAFETY SENSE™
SWAY WARNING SYSTEM
SWS is a function of LDA and is designed to detect swaying based on the \
vehicle
location in the lane and the driver’s steering wheel operation. To he\
lp prevent
swaying, the system alerts the driver using a buzzer sound and a warning\
displays
in the MID.
Continuous lane deviations from
swaying.
Gentle swaying from driver’s
inattentiveness.
Acute steering wheel operation after the
number of operations decrease due to driver’s
inattentiveness.
ADJUSTING SWAY ALERT SENSITIVITY
DISABLING LDA SWAY WARNING SYSTEM
(1) Press “” switches and select or from the Multi-Information
Display (MID).
(2) Press “
” switches and select the “Sway sensitivity” setting function a\
nd then
press “
.”
(3) Press “
” each time to change the setting.
(4) Press “
” to go back to the menu.
(1) Press “
” switches and select or from the Multi-Information
Display (MID).
(2) Press “
” switches and select the “Sway warning” setting function and t\
hen
press “
.”
(3) Press “
” each time to change the setting.
(4) Press “
” to go back to the menu.
Note: Operation of the LDA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.

38
TOYOTA SAFETY SENSE™
AHB is a safety system designed to help drivers see more of what’s ah\
ead at
nighttime while reducing glare for oncoming drivers. When enabled, AHB u\
ses an
in-vehicle camera to help detect the headlights of oncoming vehicles and\
tail lights
of preceding vehicles, then automatically switches between high and low \
beams
as appropriate to provide the most light possible and enhance forward vi\
sibility.
By using high beams more frequently, the system may allow earlier detect\
ion of
pedestrians and obstacles.
Refer to the Toyota Owner’s Manual for additional information on AHB \
operation,
settings adjustments, limitations, and precautions before attempting to \
use it.
Automatic High Beams (AHB)
(1) With the engine switch in IGNITION ON mode, turn the headlight switch to “AUTO” or “
“ position.
(2) Push lever away from you.
(3) Press the “
” switch.

The AHB indicator will come on when the headlights are turned on automat\
ically
to indicate that the system is active.
Note: Pull the lever back toward you to turn the AHB system off.
The AHB indicator will turn off. Turn switch to “
” position and the manual high
beam indicator “
” turns on.
When all of these conditions are met, high beams will be automatically t\
urned on
(after approximately 1 second): • Vehicle speed is above approximately 21 mph (34 km/h.)
• The area ahead of the vehicle is dark.
• There are no oncoming or preceding vehicles with headlights or tail\
lights turned on.
• There are few street lights on the road ahead.
If any of these conditions occur, the system is designed to automaticall\
y turn off
high beams: • Vehicle speed drops below approximately 17 mph (27 km/h.)
• The area ahead of the vehicle is not dark.
• Oncoming or preceding vehicles have headlights or tail lights turne\
d on.
• There are many streetlights on the road ahead.
ACTIVATING THE AHB SYSTEM
CONDITIONS WHERE AHB WILL TURN ON/OFF AUTOMATICALLY
(1) (2)