TOYOTA CAMRY V20 1986 Service Information
CAMRY V20 1986
TOYOTA
TOYOTA
https://www.carmanualsonline.info/img/14/57449/w960_57449-0.png
TOYOTA CAMRY V20 1986 Service Information
Page 106 of 2389
11.5
(0.453)5.0
(0.197)3.2
(0.126) B1 orifice control valve6.5
(0.256)5.0
(0.197)3.2
(0.126) No. 1 accumulator control valve9.2
(0.362)5.0
(0.197)3.2
(0.126) Cut-back valve5.0
(0.197)3.2
(0.126) 6.5
(0.256) Second coast modulator valve6.5
(0.256)5.0
(0.197)3.2
(0.126) Throttle modulator valve6.5
(0.256)5.0
(0.197)3.2
(0.126) Lock-up relay valveRetainerHeightWidthThickness
mm (in.)
AT3478 AT3479
Pin Valve
Vibrating
Stopper (Upper Side)
(Lower Side)
AT3480AT3481
LOCATION OF RETAINERS, PIN, STOPPER, CHECK BALL AND STRAINER
1. RETAINER, STOPPER AND PIN
3. STRAINER
2. CHECK BALL
- AUTOMATIC TRANSAXLEComponent Parts (Valve Body)AT-91
Page 752 of 2389
CHECK FOR SHORT CIRCUIT
(a) Remove the blown fuse and eliminate all toads from
the fuse.
(b) Connect a test bulb in place of the fuse.
(e) Establish conditions in which the test bulb comes on.
Example:
(A) ± Ignition SW on
(B) ± Ignition SW and SW 1 on
(C) ± Ignition SW, SW 1 and Relay on (Connect the
Relay) and SW 2 oft (or Disconnect SW 2)
(d) Disconnect and reconnect the connectors while
watching the test bulb.
The short lies between the connector where the test
bulb stays lit and the connector where the bulb goes
out.
(e) Find the exact location of the short by lightly shaking
the problem wire along the body. (c) Use a volt/ohmmeter with high impedance (10 k
/V
minimum) for troubleshooting of the electrical circuit.
± BODY ELECTRICAL SYSTEMGeneral InformationBE±6
Page 753 of 2389
LOCATION OF SWITCHES AND
RELAYS
± BODY ELECTRICAL SYSTEMLocation of Switches and RelaysBE±7
Page 754 of 2389
LOCATION OF SWITCHES AND
RELAYS (Cont'd)
± BODY ELECTRICAL SYSTEMLocation of Switches and RelaysBE±8
Page 755 of 2389
LOCATION OF SWITCHES AND
RELAYS (Cont'd)
± BODY ELECTRICAL SYSTEMLocation of Switches and RelaysBE±9
Page 756 of 2389
LOCATION OF SWITCHES AND
RELAYS (Cont'd)
± BODY ELECTRICAL SYSTEMLocation of Switches and RelaysBE±10
Page 757 of 2389
Fuses
1. GAUGE
2. ±
3. STOP
4. TAIL
5. CIG
6. RADIO
7. TURN
8. DEF±I/UP
9. ±
10. ENGINE
11. WIPER
12. ECU±IG
13. ±
14. IGN
15. ECU±B FUSE AND RELAY BLOCK No±1 (LOCATION: Driver's Side Kick Panel)7.5A
20A
15A
15A
7.5A
7.5A
10A
10A
20A
15A
7.5A
1 0A
FUSE AND RELAY BLOCKS
± BODY ELECTRICAL SYSTEMLocation of Switches and RelaysBE±11
Page 758 of 2389
Fuses
1. HEAD±HI (RH) 15A (CANADA)
2. HEAD±HI (LH) 15A (CANADA)
3. DOME 20A
4. ± ±
5. HEAD (RH) 15A (USA)
HEAD±LO (RH) 15A (CANADA)
6. CHARGE 7.5A
7. ER 15A
8. HAZ.HORN 15A
9. HEAD (LH) 15A (USA)
HEAD±LO (H) 15A (CANADA)Relays
A. A/C FAN No.3 Relay
B. A/C MAGNET CLUTCH Relay
(USA)
DIMMER Relay (CANADA)
C. A/C FAN No.2 Relay
D. FAN No. 1 Relay
E. HEADLIGHT Relay
F. EFI MAIN Relay
G. ENGINE MAIN Relay FUSE AND RELAY BLOCK No±2 (LOCATION: Engine Compartment)
FUSE AND RELAY BLOCKS (Cont'd)
± BODY ELECTRICAL SYSTEMLocation of Switches and RelaysBE±12
Page 963 of 2389
1. INSPECT RELAY CONTINUITY
(a) Using an ohmmeter, check that there is continuity between
terminals 1 and 3.
(b) Check that there is continuity between terminals 2 and
4.
(c) Check that there is no continuity between terminals 4
and 5.
If continuity is not as specified, replace the relay.
2. INSPECT RELAY OPERATION
(a) Apply battery voltage across terminals 1 and 3.
(b) Using an ohmmeter, check that there is continuity between
terminals 4 and 5.
(e) Check that there is no continuity between terminals 2
and 4.
If operation is not as specified, replace the relay.
ENGINE MAIN RELAY
INSPECTION OF ENGINE MAIN RELAY
LOCATION:
3S±FE In the relay box in the engine compartment.
2VZ±FE On the LH fender apron rear side in the engine
compartment.
± CHARGING SYSTEMEngine Main RelayCH±16
Page 1008 of 2389
ON±VEHICLE INSPECTION
Low Temperature (Below 835C (1815F))
1. TURN IGNITION SWITCH ºONº
Check that the fan stops.
If not, check the cooling fan relay and water temperature
switch, and check for a separated connector or severed
wire between the cooling fan relay and water temperature
switch.
2. DISCONNECT WATER TEMPERATURE SWITCH
CONNECTOR
Check that fan rotates.
If not, check the cooling fan relay, fan motor, engine main
relay and fuse, and check for a short circuit between the
cooling fan relay and water temperature switch.
3: CONNECT WATER TEMPERATURE SWITCH
CONNECTOR
ELECTRIC COOLING FAN (3S±FE)
LOCATION OF ELECTRIC COOLING
FAN COMPONENTS
± COOLING SYSTEMElectric Cooling Fan (3S±FE)CO±21