radio antenna TOYOTA GR86 2022 Owners Manual (in English)

1123-2. Opening, closing and locking the doors and trunk
switch modes are changed.
●Do not leave the electronic key on top
of the instrument panel or near the
door pockets when exiting the vehicle. Depending on the radio wave recep-
tion conditions, it may be detected by
the antenna outside the cabin and the doors will become lockable from the
outside, possibly trapping the elec-
tronic key inside the vehicle.
●As long as the electronic key is within
the effective range, the doors may be locked or unlocked by anyone. How-
ever, only the doors detecting the
electronic key can be used to unlock the vehicle.
●Even if the electronic key is not inside the vehicle, it may be possible to start
the engine if the electronic key is near
the window.
●The doors may unlock or lock if a
large amount of water splashes on the door handle, such as in the rain or in a
car wash, when the electronic key is
within the effective range. (The doors will automatically be locked after
approximately 30 seconds if the doors
are not opened and closed.)
●If the wireless remote control is used
to lock the doors when the electronic key is near the vehicle, there is a pos-
sibility that the door may not be
unlocked by the entry function. (Use the wireless remote control to unlock
the doors.)
●Touching the door lock or unlock sen-
sor while wearing gloves may prevent
lock or unlock operation.
●Vehicles without a double locking sys-
tem: When the lock operation is per-
formed using the lock sensor, recognition signals will be shown up to
three consecutive times. After this, no
recognition signals will be given.
●If the door handle becomes wet while
the electronic key is within the effec- tive range, the door may lock and
unlock repeatedly. In this case, follow
the following correction procedures to
wash the vehicle:
• Place the electronic key in a location 2 m (6 ft.) or more away from the vehi-
cle. (Take care to ensure that the key
is not stolen.) • Set the electronic key to battery-sav-
ing mode to disable the smart entry &
start system. ( P. 1 1 1 )
●If the electronic key is inside the vehi-
cle and a door handle becomes wet during a car wash, a message may be
shown on the multi-information dis-
play and a buzzer will sound outside the vehicle. To turn off the alarm, lock
both side doors.
●The lock sensor may not work prop-
erly if it comes into contact with ice,
snow, mud, etc. Clean the lock sensor and attempt to operate it again.
●A sudden handle operation or a han-dle operation immediately after enter-
ing the effective range may prevent
the doors from being unlocked. Touch the door unlock sensor and check that
the doors are unlocked before pulling
the door handle again.
●Unlocking the vehicle may take more
time if another electronic key is within the effective range.
■When the vehicle is not driven for
extended periods
●To prevent theft of the vehicle, do not
leave the electronic key within 2 m (6
ft.) of the vehicle.
●The smart entry & start system can be
deactivated in advance. ( P. 1 1 3 )
●Setting the electronic key to bat-
tery-saving mode helps to reduce key battery depletion. ( P. 1 1 1 )
■To operate the system properly
●Make sure to carry the electronic key
when operating th e system. Do not get the electronic key too close to the
vehicle when operating the system
from the outside of the vehicle.
Depending on the position and holding
condition of the electronic key, the key may not be detected correctly and the

113
3
3-2. Opening, closing and locking the doors and trunk
Before driving
system may not operat e properly. (The
alarm may go off accidentally, or the door lock prevention function may not
operate.)
●Do not leave the electronic key inside
the trunk.
The key confinement prevention func- tion may not operate, depending on
the location of the key (the inside
edge of the Trunk), conditions (inside a metal bag, close to metallic objects)
and the radio waves in the surround-
ing area. ( P.109)
■If the smart entry & start system does not operate properly
●Locking and unlocking the doors:  P. 3 5 7
●Starting the engine: P. 3 5 8
■Customization
Some functions can be customized.
( P.377)
■If the smart entry & start system
has been disabled
●Locking and unlocking the doors:
Use the wireless remote control or mechanical key. ( P.103, 357)
●Starting the engine and changing engine switch modes: P. 3 5 8
●Stopping the engine: P. 1 4 1
In the following situations, the
smart entry & start system should
be disabled.
 When people with implantable
cardiac pacemakers, cardiac
resynchronization therapy pace-
WA R N I N G
■Caution regarding interference
with electronic devices
●People with implantable cardiac pacemakers, cardiac
resynchronization therapy-pace-
makers or implantable cardioverter defibrillators should maintain a rea-
sonable distance between them-
selves and the smart entry & start
system antennas. ( P.110) The radio waves may affect the
operation of such devices. If neces-
sary, the entry function can be disa- bled. Ask any authorized Toyota
retailer or Toyota authorized
repairer, or any reliable repairer for details, such as the frequency of
radio waves and timing of the emit-
ted radio waves. Then, consult your doctor to see if you should disable
the entry function.
●Users of any electrical medical
device other than implantable car-
diac pacemakers, cardiac resynchronization therapy-pace-
makers or implantable cardioverter
defibrillators should consult the manufacturer of the device for infor-
mation about its operation under
the influence of radio waves. Radio waves could have unex-
pected effects on the operation of
such medical devices.
The smart entry & start system can be
disabled. ( P.113)
When to disable the smart
entry & start system

237
4
4-6. Using other driving systems
Driving
have the system inspected.
• A sticker, paint, or a chemical is applied to the sonar sensors or the
rear bumper near the sonar sensor.
• The rear bumper is modified. • The rear bumper has been removed
and attached.
• The ground clearance is changed due to the vehicle’s loading condition or
modification.
• There is damage to the sonar sensors or the rear bumper near the sonar
sensor.
• The rear bumper is exposed to strong impact, or the rear bumper is
deformed.
●On a steep hill, the system’s auto-
matic braking ability will be reduced.
●The system is designed to avoid colli-
sions by automatic hard braking when
the vehicle’s reversing speed is less than approximately 5 km/h (3 mph).
However, the system does not guar-
antee that the vehicle will be able to avoid collisions in any situation.
●If the vehicle is reversed at an extremely slow speed, the driver’s
operation may be prioritized. In this
case, automatic braking will not oper- ate.
●The system may not be able to detect and apply the brake with the following
objects.
• Sharp or thin objects such as poles, fences and ropes which may not
reflect the sound wave emitted from
the sonar sensor. • Objects that are too close to the rear
bumper when the shift lever is set to
R. • Objects with a surface which may not
reflect the sound wave emitted from
the sonar sensor such as a chain link
fence.
●Objects the system is not designed to
detect and apply brake. • Pedestrians.
• Moving objects including moving vehi-
cles. • Objects which absorbs sound waves
such as cloth or snow.
• Objects whose surface has a diagonal
angle. • Objects that are low to the ground
such as parking blocks.
• Objects that are high above the ground such as objects hanging from
above.
• Objects that are out of range of the center of the vehicle in the horizontal
direction.
• Objects that are not in a vertical direc- tion.
• Objects which are not perpendicular
to the ground. • Objects which are not directly in the
traveling direction of the vehicle.
• Objects which are uneven or wavy.
●When reversing the vehicle, the func-
tions may not be able to work properly or may cause a system malfunction if
the following conditions exist.
High frequency sound from other
sources are nearby:
• Horn sound from another vehicle. • Engine sound from other vehicles.
• Sound of an air brake.
• Vehicle detection equipment or a sonar from another vehicle.
• A sound wave with a frequency similar
to the vehicle’s system is transmitted near by.
• A vehicle equipped with the same sys-
tem is reversing toward your reversing direction.
●Weather conditions:• Extremely high or extremely low tem-
peratures in which the area near the
sonar sensor becomes too hot or too cold to operate.
• The sonar sensors or the rear bumper
near the sonar sensors are exposed to heavy rain or a significant amount
of water.
• Fog, snow or sandstorm, etc.
• Air is moving rapidly such as when a strong wind is blowing.
●Parts attached to the rear bumper near the sonar sensor:
• Commercial electronic parts (fog light,
fender pole, radio antenna) or com- mercial attachment parts (trailer hitch,

33
3
3-2. Other settings
Settings
4 Select “PIN Setup” or “Push But-
ton Setup” as determined by the
device.
5 Operate the Wi-Fi® device to
connect.
 When “PIN Setup” is selected:
Enter the displayed PIN code
into the Wi-Fi® network device.
 When “Push Button Setup” is
selected: Push the WPS button
on the Wi-Fi® network device.
Available networks which are not
displayed by searching can be
added.
1 Display the general settings
screen. ( P. 2 9 )
2 Select “Wi-Fi”.
3 Select “Available Wi-Fi Net-
works”.
4 Select “Add”.
5 Select “Wi-Fi Name (SSID)”.
6 Enter the network name.
7 Select “OK”.
8 Select “Security”.
9 Select the security type.
10 Select “Start Connection”.
 When a password is required,
enter the password. Select “OK”.
1 Display the general settings
screen. ( P. 2 9 )
2 Select “Wi-Fi”.
3 Select “Wi-Fi” to turn the Wi-Fi®
function off.
4 Select “Registered Wi-Fi Net-
works”.
5 Select “Delete”.
6 Select for the Wi-Fi® net-
work you wish to delete.
7 Select “OK”. Adding a Wi-Fi® network
Deleting a Wi-Fi® network
WA R N I N G
●Use Wi-Fi® devices only when safe
and legal to do so.
●This system is fitted with Wi-Fi®
antennas. People with implantable
cardiac pacemakers , cardiac resyn-
chronisation therapy-pacemakers or implantable cardioverter
defibrillators should maintain a rea-
sonable distance between them-
selves and the Wi-Fi® antennas.
The radio waves may affect the
operation of such devices.
●Before using Wi-Fi® devices, users
of any electrical medical device other than implantable cardiac
pacemakers, cardiac resynchroni-
sation therapy-pacemakers or implantable cardioverter
defibrillators should consult the
manufacturer of the device for infor- mation about its operation under
the influence of radio waves.
Radio waves could have unex- pected effects on the operation of
such medical devices.

43
4
4-1. Phone operation (Hands-free system for mobile phones)
Phone
●If your mobile phone does not support
Bluetooth®, this system cannot func-
tion. Certain functions may not be available depending on the type of
mobile phone.
●In the following conditions, the system
may not function:
• The mobile phone is turned off. • The current position is outside the
communication area.
• The mobile phone is not connected. • The mobile phone has a low battery.
●When using the hands-free function
and other Bluetooth® functions at the same time, the following problems
may occur:
• The Bluetooth® connection may be cut.
• Noise may be heard when playing
back voice with the Bluetooth® func- tion.
●The other party’s voice will be heard from the front speakers. The
audio/visual system will be muted dur-
ing phone calls or when hands-free voice commands are used.
●Talk alternately with the other party on
the phone. If both parties speak at the
same time, the other party may not hear what has been said. (This is not
a malfunction.)
●Keep call volume down. Otherwise,
the other party’s voice may be audible
outside the vehicle and voice echo may increase. When talking on the
phone, speak clearly towards the
microphone.
●The other party may not hear you
clearly when: • Driving on an unpaved road. (Making
excessive traffic noise.)
• Driving at high speeds. • Driving with a window open.
• When air from the ventilator blows
directly toward the microphone. • The sound of the air conditioning fan
is loud.
• There is a negative effect on sound quality due to the phone and/or net-
work being used.
Some basics
The hands-free system ena-
bles calls to be made and
received without having to take
your hands off the steering
wheel.
This system supports
Bluetooth®. Bluetooth® is a
wireless data system that ena-
bles mobile phones to be used
without being connected by a
cable or placed in a cradle.
The operating procedure of the
phone is explained here.
WA R N I N G
●While driving, do not use a mobile
phone or connect the Bluetooth®
phone.
●This system is fi tted with Bluetooth®
antennas. People with implantable
cardiac pacemakers , cardiac resyn-
chronisation therapy-pacemakers or implantable cardioverter
defibrillators should maintain a rea-
sonable distance between them-
selves and the Bluetooth®
antennas. The radio waves may
affect the operation of such devices.

786-3. Media operation
when Bluetooth® audio is being
played.
●For operating the portable player, see
the instruction manual that comes with it.
●If the Bluetooth® device is discon-
nected due to poor reception from the
Bluetooth® network when the engine switch is changed to ACC or ON, the
system will automatica lly reconnect to
the portable player.
●If the Bluetooth® device is discon-
nected on purpose, such as it was turned off, this does not happen.
Reconnect the portable player manu-
ally.
●Bluetooth® device information is regis-
tered when the Bluetooth® device is
connected to the Bluetooth®
audio/visual system. When selling or disposing of the vehicle, remove the
Bluetooth® audio information from the
system. ( P. 2 9 )
●Depending on the Bluetooth® device
or music file being played, the cover
art may not be displayed.
●If the Bluetooth® device does not play
automatically when connected, device
operation may be necessary.
To use the Bluetooth® audio/visual
system, it is necessary to register a
Bluetooth® device with the system.
Registering an additional device
1 Select “Manage Devices” on the
Bluetooth® audio control screen.
2 For more information: P. 2 4
Selecting a registered device
1 Select “Manage Devices” on the
Bluetooth® audio control screen.
2 Select the Bluetooth® device to
be connected.
WA R N I N G
●Do not operate the player’s controls
or connect to the Bluetooth® audio/visual system while driving.
●This system is fitted with Bluetooth®
antennas. People with implantable
cardiac pacemakers, cardiac resyn- chronisation therapy-pacemakers
or implantable cardioverter
defibrillators should maintain a rea- sonable distance between them-
selves and the Bluetooth®
antennas. The radio waves may affect the operation of such
devices.
●Before using Bluetooth® devices,
users of any electrical medical
device other than implantable car- diac pacemakers, cardiac resyn-
chronisation therapy-pacemakers
or implantable cardioverter defibrillators should consult the
manufacturer of the device for infor-
mation about its operation under the influence of radio waves. Radio
waves could have unexpected
effects on the operation of such medical devices.
NOTICE
●Do not leave your portable player in
the vehicle. In particular, high tem-
peratures inside the vehicle may damage the portable player.
Connecting a Bluetooth®
device

83
6
6-5. Tips for operating the audio/visual system
Audio
6-5.Tips for operating the audio/visual system
●The use of a mobile phone inside or
near the vehicle may cause a noise from the speakers of the audio/visual
system which you are listening to.
However, this does not indicate a mal- function.
Usually, a problem with radio recep-
tion does not mean there is a prob-
lem with the radio  it is just the
normal result of conditions outside
the vehicle.
For example, nearby buildings and
terrain can interfere with FM recep-
tion. Power lines or phone wires
can interfere with AM signals. And
of course, radio signals have a lim-
ited range. The farther the vehicle
is from a station, the weaker its sig-
nal will be. In addition, reception
conditions change c onstantly as the
vehicle moves.
Here, some common reception
problems that probably do not indi-
cate a problem with the radio are
described.
■FM
Fading and drifting stations: Gener-
ally, the effective range of FM is
about 40 km (25 miles). Once out-
side this range, you may notice fad-
ing and drifting, wh ich increase with
the distance from the radio trans-
mitter. They are often accompanied
by distortion.
Multi-path: FM signals are reflec-
tive, making it possible for 2 signals
to reach the vehicle’s antenna at
the same time. If this happens, the
signals will cancel each other out,
causing a momentary flutter or loss
of reception.
Static and fluttering: These occur
when signals are blocked by build-
ings, trees or other large objects.
Increasing the bass level may
reduce static and fluttering.
Station swapping: If the FM signal
being listened to is interrupted or
weakened, and there is another
strong station nearby on the FM
band, the radio may tune in the
second station until the original sig-
nal can be picked up again.
■AM
Fading: AM broadcasts are
reflected by the upper atmosphere
 especially at night. These
reflected signals can interfere with
those received directly from the
radio station, causing the radio sta-
tion to sound alternately strong and
weak.
Station interference: When a
reflected signal and a signal
received directly from a radio sta-
tion are very nearly the same fre-
quency, they can interfere with
Operating infor mation
NOTICE
●To avoid damage to the
audio/visual system, be careful not
to spill beverages over the audio/visual system.
Radio