display TOYOTA HIGHLANDER 2001 Service Repair Manual

xi
7Mapº switch
You can select a destination simply by
touching the location on the displayed map.
34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8Intersectionº switch
You can enter the names of two intersecting
streets. This is helpful if you do not know the
specific street address of your destination
but know the general vicinity. 35. . . . . . . . .
9Freeway Ent./Exitº switch
You can enter the name of a freeway (inter-
state) entrance or exit. 36. . . . . . . . . . . . . . .
10Phone #º switch
You can enter a destination by the telephone
number. 37. . . . . . . . . . . . . . . . . . . . . . . . . . .
11Coordinatesº switch
You can set a destination using latitude and
longitude coordinates. 37. . . . . . . . . . . . . . .
12Quick access switch
You can select one of 5 preset destinations
directly. To use this function, it is necessary
to set the Attributeº for each memory point.
(To register the Quick Accessº, see page
70.) 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13Home switch
You can select your own home without en-
tering the address each time. To use this
function, it is necessary to set the Attributeº
for the memory point. (To register the
Homeº, see page 70.) 22. . . . . . . . . . . . . .
14Changeº switch
To change the search area, touch this
switch. 20. . . . . . . . . . . . . . . . . . . . . . . . . . . .

xiiThe switches below perform the follow-
ing operations.
1Map DVDº switch
Displays information regarding the disc ver-
sion or covered area. 12. . . . . . . . . . . . . . . .
2Select Userº switch
Enables recall of up to three memorized user
setting patterns. 63. . . . . . . . . . . . . . . . . . . .
3Setupº switch
Enables various settings for the navigation
system. 76. . . . . . . . . . . . . . . . . . . . . . . . . . .
4My Placesº switch
Enables changes to Memory pointsº and
Areas to avoidº. 66. . . . . . . . . . . . . . . . . . . .
5Suspend Guidanceº and Resume
Guidanceº switch
Suspends or resumes the guidance.
62 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6Volumeº switch
Sets the volume of the voice guidance.
63 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ð Menuº screen

F46319
Skid Control ECU
with Actuator
Passenger Side J/BENG+ TRC-
TRC+
ENG-
CG D3
DLC3
W-BY-B
W-B TC TRC-
TRC+
ENG-
ENG+ ECM
E5
24Y G
V R
E531
E525
E5
3022
S27
8
23
9
4
4L1
4N
7 4C6
IC IC4
E5
20
TCIC4
IC4
IC4S27
S27
S27
OOJ16
J/C
DD
W-BG-B
W-G
W-L 19
7
18
5
13 05-868
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1058 Author
: Date
:
TC AND CG TERMINAL CIRCUIT
CIRCUIT DESCRIPTION
Connecting terminals TC and CG of the DLC3 causes the ECU to display the DTC by flashing the ABS warn-
ing light.
WIRING DIAGRAM
05F1X-07

G24767
GND1IG1
Skid Control ECU
(harness side connector)
S27
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
05-849
1039 Author
: Date
:
4 INSPECT SKID CONTROL ECU TERMINAL VOLTAGE(IG1 TERMINAL)
WHEN USING HAND-HELD TESTER:
(a) Connect the hand-held tester to the DLC3.
(b) Start the engine.
(c) Select the DATA LIST mode on the hand-held tester.
(d) Check the voltage condition output from the ECU displayed on the hand-held tester.
ItemMeasurement Item /
Range (Display)Normal Condition
IG VOLTAGEECU power supply voltage / TOO
LOW / NORMALNORMAL: 9.5 V or over
UNDER: Below 9.5 V
OK:
ºNormalº is displayed.
WHEN NOT USING HAND-HELD TESTER:
(a) Disconnect the skid control ECU connector.
(b) Turn the ignition switch to the ON position.
(c) Measure the voltage according to the value(s) in the table
below.
Standard:
Tester ConnectionSpecified Condition
S27-46 (IG1) - S27-32 (GND1)11 to 14 V
NG REPAIR OR REPLACE HARNESS OR
CONNECTOR
OK