wiring diagram TOYOTA HIGHLANDER 2001 Service Repair Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2001, Model line: HIGHLANDER, Model: TOYOTA HIGHLANDER 2001Pages: 2572, PDF Size: 34.8 MB
Page 741 of 2572
F46304
Combination Meter
Passenger Side J/BABS C11
Instrument Panel J/BSkid Control ECU with Actuator
I15
Ignition SW
F7
FL BlockC11 IF2
IL1 IC4 S27
S27 S27 4E
4H 4JJ6
J/C
IC4
IC1 1A
1C 1D
1G
1C 1C ECU-IG
IGN
AM1IG1 4M
IG2AM1
AM2WA
IG1
GND1
EA EB ALT
AM2
J4
J/C FL MAIN
Battery1
24 6
7 9
10 13
1729
4
446
4
62
10
32 12
12
1 E P W SB R-L
P
ESB
GRB-R
G
GR
W
Y
L-Y WB
W-B Y
W
AW-B 167 10
1
6 05-840
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1030 Author: Date:
ABS WARNING LIGHT CIRCUIT (REMAINS ON)
CIRCUIT DESCRIPTION
During DTC read by SST (CHECK WIRE), if the ABS warning light remains on, troubleshoot by following
this inspection flow.
WIRING DIAGRAM
05CDG-1 1
Page 745 of 2572
F50610
Skid Control ECU with Actuator Combination Meter
B4
Brake Warning SW
Passenger Side J/B
Instrument Panel J/B
I15
Ignition SW
F7
FL Block Brake
IGN
AM2BRL
PKB
AM2 IG2
FL MAIN
BatteryC11 IF3 IC4 S27
IL1
S27 C12
C12IF3
IC4
4E 4M
1C
1G4J
4MIC4
IC1Passenger Side J/B
P3
Parking
Brake SW J4
J/C
EB1
2
3 46
791011 13
1644
15
1
28 J6
J/C
11
9
16
6
1
10
1 1
1 B
PR V
W YSB
P
EER-B SB
R-W
LG
B
A L-Y GRW W-B
LG-B
05-854
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1044 Author: Date:
BRAKE WARNING LIGHT CIRCUIT
CIRCUIT DESCRIPTION
The BRAKE warning light comes on when the brake fluid is insufficient, the parking brake is applied or the
EBD is defective.
WIRING DIAGRAM
05F1V-09
Page 750 of 2572
F46304
Combination Meter
Passenger Side J/BABS C11
Instrument Panel J/BSkid Control ECU with Actuator
I15
Ignition SW
F7
FL BlockC11 IF2
IL1 IC4 S27
S27 S27 4E
4H 4JJ6
J/C
IC4
IC1 1A
1C 1D
1G
1C 1C ECU-IG
IGN
AM1IG1 4M
IG2AM1
AM2WA
IG1
GND1
EA EB ALT
AM2
J4
J/C FL MAIN
Battery1
24 6
7 9
10 13
1729
4
446
4
62
10
32 12
12
1 E P W SB R-L
P
ESB
GRB-R
G
GR
W
Y
L-Y WB
W-B Y
W
AW-B 167 10
1
6 05-844
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1034 Author: Date:
ABS WARNING LIGHT CIRCUIT (DOES NOT LIGHT UP)
WIRING DIAGRAM
05F1T-06
Page 771 of 2572
F40566
Skid Control ECU with Actuator
2
1
1817
FL+
FL- A4
ABS Speed Sensor
Front LH
43
FR+
FR- A5
ABS Speed Sensor
Front RHS27 R-Y
LG
O
P 2
1S27
S27
S27
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
05-789
979 Author: Date:
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand-held tester and start from step 3 when not using the
hand-held tester.
1 READ VALUE OF HAND-HELD TESTER(FRONT SPEED SENSOR)
(a) Connect the hand-held tester to the DLC3.
(b) Start the engine.
(c) Select the DATA LIST mode on the hand-held tester.
(d) Check that there is no difference between the speed value output from the speed sensor displayed
on the hand-held tester and the speed value displayed on the speedometer when driving the vehicle.
ItemMeasurement Item /
Range (Display)Normal Condition
WHEEL SPD FR
Wheel speed sensor (FR) reading /
min.: 0 km/h (0 MPH, max.: 326 km/h
(202 MPH)
Actual wheel speed
WHEEL SPD FL
Wheel speed sensor (FL) reading /
min.: 0 km/h (0 MPH, max.: 326 km/h
(202 MPH)
Actual wheel speed
OK:
There is almost no difference from the displayed speed value.
HINT:
There is tolerance of + 10 % in the speedometer indication.
NG Go to step 3
OK
Page 777 of 2572
F46312
Skid Control ECU with Actuator
1 2206
S27
A25
ABS Speed Sensor
Rear RH
5 19 A24
ABS Speed Sensor
Rear LH
1 12
IO2
6 15 16
7
RR-
RR+ RL-
RL+ IC2 IA1
1 2IO2IA1 IC2
IC2
IC2 2
2S27
S27
S27 G
L O
PR V
Y R
GRBR
Y Y-G
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
05-795
985 Author: Date:
DTC C0210/33 RIGHT REAR SPEED SENSOR
DTC C0215/34 LEFT REAR SPEED SENSOR
DTC C1238/38 FOREIGN MATTER IS ATTACHED ON TIP OF
RIGHT REAR SENSOR
DTC C1239/39 FOREIGN MATTER IS ATTACHED ON TIP OF
LEFT REAR SENSOR
CIRCUIT DESCRIPTION
Refer to DTC C0200/31, C0205/32, C1235/35, C1236/36 on page 05-788.
DTC No.DTC Detecting ConditionTrouble Area
C0210/33
C0215/34
(1) All the following conditions continues for at least 1 se-
cond.
Vehicle speed is more than 6 mph (10 km/h).
Open or short in vehicle speed sensor signal circuit of
faulty wheel continues for 1 second or more.
(2) Momentary interruption of the sensor signal of faulty
wheel has occurred 7 times or more.
(3) Sensor signal circuit is open for 0.5 seconds.
Right rear and left rear speed sensor
Each speed sensor circuit
Sensor rotor
Sensor installation
C1238/38
C1239/39All the following conditions for at least 5 seconds.
Vehicle speed is more than 12 mph (20 km/h).
Vehicle speed sensor signal receives.Right rear and left rear speed sensor
Each speed sensor
Sensor installation
HINT:
DTC C0210/33 and C1238/38 are for the right rear speed sensor.
DTC C0215/34 and C1239/39 are for the left rear speed sensor.
WIRING DIAGRAM
05H3B-03
Page 785 of 2572
F46309
Skid Control ECU with Actuator F7
FL Block
FL MAIN
Battery
EA EB ABS1+BS
GND1
J4
J/C 1831
32
AB W
W-BS27
S27 W-B
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
05-803
993 Author: Date:
WIRING DIAGRAM
INSPECTION PROCEDURE
1 RECONFIRM DTC
HINT:
This code is detected when a problem is determined in the brake actuator assy.
The solenoid circuit is in the brake actuator assy.
Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check
if the DTC code is output before replacing the brake actuator assy.
(a) Clear the DTCs(see page 05-765).
(b) Turn the ignition switch to the ON position.
(c) Are the same DTCs recorded?
NO PROCEED TO NEXT CIRCUIT INSPECTION
SHOWN IN PROBLEM SYMPTOMS TABLE
(SEE PAGE 05-786).
YES
REPLACE ABS & TRACTION ACTUATOR ASSY (SEE PAGE 32-37)
Page 787 of 2572
F46308
Skid Control ECU with Actuator
ABS MTR Relay
ABS CUT Relay
FL MAIN
BatteryS27
S27
S27
S27
ABS2 F7
FL Block ABS R/BR+
MR
BM
MRF 12
3 5
91415 45
5
55
55
555
1
2 35
12
B
W B-OLG
W-L
B-R
G-RB-O
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
05-805
995 Author: Date:
WIRING DIAGRAM
Page 791 of 2572
F46309
Skid Control ECU with Actuator F7
FL Block
FL MAIN
Battery
EA EB ABS1+BS
GND1
J4
J/C 1831
32
AB W
W-BS27
S27 W-B
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
05-809
999 Author: Date:
DTC C0278/11 OPEN CIRCUIT IN ABS SOLENOID RELAY
CIRCUIT
DTC C0279/12 SHORT CIRCUIT IN ABS SOLENOID RELAY
CIRCUIT
CIRCUIT DESCRIPTION
The ABS solenoid relay is built in the ABS & TRACTION Actuator assy. This relay supplies power to each
ABS solenoid. If the initial check is OK, after the ignition switch is turned to the ON position, the relay goes
on.
DTC No.DTC Detecting ConditionTrouble Area
C0278/11
When any of the following (1 to 2) is detected:
(1) All the following conditions continues for at least 0.2
seconds.
IG voltage is between 9.5 and 17.2 V.
Relay contact is open when the relay is ON.
(2) All the following conditions continues for at least 0.2
seconds.
IG voltage is 9.5 V or less when the relay is ON.
Relay contact remains open.
ABS No.1 fuse
ABS SOL relay
ABS SOL relay circuit
ABS & TRAC actuator
C0279/12
The following condition continue for at least 0.2 seconds.
Relay contact is closed immediately after turning IG switch
to the ON position when the relay is OFF.ABS No.1 fuse
ABS SOL relay
ABS SOL relay circuit
ABS & TRAC actuator
WIRING DIAGRAM
05CD5-19
Page 795 of 2572
F46313
ENG- ENG+
TRC+
TRC-24
30
31 25239
8
22 S27 S27
S27
S27 E5 ECM
E5 E5E5 ENG+
ENG-
TRC+
TRC- Skid Control ECU with Actuator
IC4 V
GR
IC4
IC4
IC4 YW-L
W-G
G-B
Y-B 185
7
19
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
05-813
1003 Author: Date:
DTC C1203/53 ECM COMMUNICATION CIRCUIT
MALFUNCTION
CIRCUIT DESCRIPTION
The circuit is used to send TRAC & VSC control information from the skid control ECU to the ECM (TRC+,
TRC-), and engine control information from the ECM to the skid control ECU (ENG+, ENG-).
DTC No.DTC Detecting ConditionTrouble Area
C1203/53
When any of the following (1 to 3) is detected:
(1) All the following conditions continues for at least 5 se-
conds.
IG1 terminal voltage is 9.5 V or more.
Cannot send data to ECM.
(2) All the following conditions continues for at least 5 se-
conds.
IG1 terminal voltage is more than 9.5 V.
Engine speed is 500 rpm or more.
Cannot receive data from ECM.
(2) All the following conditions repeats 10 times in a series.
Cannot send data to ECM.
Cannot receive data from ECM.
Both of the above occur at least once within 5 sec.
TRC+ or TRC- circuit
ENG+ or ENG- circuit
ECM
WIRING DIAGRAM
05CDQ-14
Page 800 of 2572
F46314
Skid Control ECU
with Actuator
S2710
E517
NEO NEO ECM
IC43
BV 05-818
- DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1008 Author: Date:
DTC C1224/44 NE SIGNAL CIRCUIT
CIRCUIT DESCRIPTION
The skid control ECU receives engine revolution speed signals (NE signals) from the ECM.
DTC No.DTC Detecting ConditionTrouble Area
C1224/44
When any of the following (1 to 2) is detected:
(1) Any of the following conditions continues for at least 10
seconds.
Data can be received properly from ECM at a speed of
more than 19 mph (30 km/h).
Open or short in engine rpm signal circuit.
(2) Any of the following conditions continues for at least
0.24 seconds.
TRAC is in operation.
Open or short in engine rpm signal circuit.
NEO circuit
ECM
Skid control ECU
WIRING DIAGRAM
05CD9-17