air condition TOYOTA HIGHLANDER 2007 XU40 / 2.G Navigation Manual

51
(d) Detour setting
While the route guidance is operating, you
can change the route to detour around a
section of the route where a delay is
caused by road repairs, an accident, etc.
1. Touch the
“Route” switch.
2. Touch the “Detour” switch.
3. Select the switch below to select the
desired detour distance.
“1 Mile (km)”, “3 Miles (km)” or “5 Miles
(km)”: Touch one of these switches to start
the detour process. After detouring, the sys-
tem returns to the original guidance route.
“Whole Route”: If you touch this switch, the
system will calculate an entire new route to
the destination.
This picture shows an example of how the
system would guide you around a delay
caused by a traffic jam.
1This position indicates the location of a
traffic jam caused by road repairs or an
accident.
2This route indicates the detour sug-
gested by the system.
INFORMATION
When your vehicle is on a freeway, the
detour distance selections are 5, 15,
and 25 miles (km).
The system may not be able to calcu-
late a detour route depending on the
selected distance and surrounding
road conditions.

101 Information items
Change oil.
Replace oil filter.
Rotate tires.
Replace tires.
Replace battery.
Replace brake linings.
Replace wiper blades.
Replace engine coolant.
Replace brake fluid.
Replace ATF.
Scheduled maintenance.
Replace air filter.
Personal items.
When you touch the
“PERSONAL
ITEMS”
switch on the “Maintenance”
screen, the screen changes to the “Personal
Event” screen. Touch the keys to input the de-
sired name and then input conditions.
3. Input the conditions.
Notice of “Date”: You can input the next
maintenance date.
Notice of “Distance”: You can input the driv-
ing distance until the next maintenance
check.
After you input the date and/or distance,
touch the
“OK” switch. The screen then re-
turns to the “Maintenance” screen.

11 4
(a) Automatic transition
You can select a function that enables au-
tomatic return to the navigation screen
from the audio or air conditioner screen.
Select “ON” or “OFF” and then touch
the
“OK” switch.
“ON”:The navigation screen automatically
returns from the audio or air condi-
tioner screen 20 seconds after the
end of audio or air conditioner
screen operation.
“OFF”:The audio or air conditioner screen
remains on.
(b) Background color
You can select a background color.
Select the desired background color and
then touch the
“OK” switch.
Screen adjustment
The brightness or contrast of the screen
can be adjusted depending on the bright-
ness of your surroundings. You can also
turn the display off.
To display the “Display” screen push the
“DISPLAY” button.
Contrast and brightness adjustment
“CONTRAST” “+”:
Strengthens the contrast of the screen.
“CONTRAST” “”:
Weakens the contrast of the screen.
“BRIGHTNESS” “+”:
Brightens the screen.
“BRIGHTNESS” “”:
Darkens the screen.
After adjusting the screen, touch the
“OK” switch.

152 CARING FOR YOUR CASSETTE PLAYER
AND TAPES
For the best performance for your cassette
player and tapes:
Clean the tape head and other parts regularly.
A dirty tape head or tape path can de-
crease sound quality and tangle your cas-
sette tapes. The easiest way to clean
them is by using a cleaning tape. (A wet
type is recommended.)
Use high−quality cassettes.
Low−quality cassette tapes can cause
many problems, including poor sound, in-
consistent playing speed, and constant
auto−reversing. They can also get stuck
or tangled in the cassette player.
Do not use a cassette if it has been dam-
aged or tangled or if its label is peeling off.
Do not leave a cassette in the player if you
are not listening to it, especially if it is hot
outside.
Store cassettes in their cases and out of
direct sunlight.
Avoid using cassettes with a total playing
time longer than 100 minutes (50 minutes
per side). The tape used in these cas-
settes is thin and could get stuck or
tangled in the cassette player.CARING FOR YOUR COMPACT DISC
PLAYER, DVD PLAYER AND DISCS
Your compact disc player is intended for
use with 12 cm (4.7 in.) discs only.
Extremely high temperatures can keep
your compact disc player and DVD player
from working. On hot days, use the air
conditioning to cool the vehicle interior be-
fore you use the players.
Bumpy roads or other vibrations may
make your compact disc player and DVD
player skip.
If moisture gets into your compact disc
player and DVD player, the players may
not play even though they appear to be
working. Remove the disc from the player
and wait until it dries.
CAUTION
Compact disc players and DVD players
use an invisible laser beam which could
cause hazardous radiation exposure if
directed outside the unit. Be sure to op-
erate the players correctly.
Compact disc player
Use only compact discs marked as shown
above. The following products may not be
playable on your compact disc player.
SACDs
dts−CDs
Copy−protected CDs
CD−Rs (CD−Recordable)
CD−RWs (CD−Re−writable)
CD−ROMs

155
AIR CONDITIONING
Air conditioning
Automatic air conditioning controls156 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION VI

156Page
1“A/C” switch 159. . . . . . . . . . . . . . . . .
2Outside temperature display
(in degrees Fahrenheit or
Centigrade) 162. . . . . . . . . . . . . . . . . .
3Air flow control switch 158. . . . . . . .
4Temperature display
(in degrees Fahrenheit or
Centigrade) 161. . . . . . . . . . . . . . . . . .
5Fan speed control switch 158. . . . .
6Air intake selector button 159. . . . .
7For information about the “Rear win-
dow defogger”, please refer to the
Owner’s Manual.
8Windshield air flow button 161. . . .
9Air conditioning operation
screen display (“CLIMATE”)
button 157. . . . . . . . . . . . . . . . . . . . . . .
10“OFF” button 158. . . . . . . . . . . . . . . .
11“AUTO” button 160. . . . . . . . . . . . . . .
12“TEMP” button 161. . . . . . . . . . . . . . .
Automatic air conditioning controls

157
— “CLIMATE” control
Push this button to display switches for
automatic air conditioning controls.
The ignition key must be in the “ON” position.
NOTICE
To prevent the battery from being dis-
charged, do not leave the air condition-
ing on longer than necessary when the
engine is not running.
Air flow selection
6U302 paste

158
— Manual control
SETTING OPERATION
When one of the manual control switches
is depressed while operating in automatic
mode, the operation corresponding to the
depressed switch is set. Other conditions
continue to be adjusted automatically.
(a) Air flow selection
The outlets from which air is delivered can
be selected manually by touching the
switch.
The function of each mode is as follows:
1Panel — Air flows mainly from the instru-
ment panel vents.
2Bilevel — Air flows from both the floor
vents, instrument panel vents.
When you set the temperature selector
setting at about the middle in automatic
operation, warm air flows out of the floor
vents and relatively low − temperature
air flows out of the instrument panel
vents.
3Floor — Air flows mainly from the floor
vents.
4Floor/windshield — Air flows mainly
from the floor vents, windshield vents.
Take in the fresh air with selecting the
FRESH mode by the air intake control
button.
The selected mode is highlighted in green.
(b) Fan speed control
1Fan speed at low
2Fan speed at high
The fan speed can be set to your desired
speed by touching the appropriate air flow
control switch.
The higher the fan speed is, the more air is de-
livered.
Pushing the “OFF” button turns off the
fan.
To remove the exterior windshield frost and in-
terior windshield fog, use the high speed set-
ting.
The selected mode is highlighted in green.

159
(c) Air intake selector
1RECIRCULATED — Recirculates the
air inside the vehicle.
2FRESH — Draws outside air into the
system.
Each time you push the air intake control
button.
The mode changes in order from the RECIR-
CULATED mode to FRESH mode, then back
to the RECIRCULATED mode.
Each indicator light shows which mode is now
selected.
If quick circulation of cooled air is desired,
push the air intake selector button for RECIR-
CULATED mode.For normal use, it is best to keep the air intake
selector button set to the FRESH mode. If re-
circulated air is used during heating, the win-
dows will fog up more easily.
To prevent fogging up of the windshield, the
air intake mode may change automatically to
the FRESH mode depending on the condition
of the air conditioning system.
For example, when the ambient temperature
is low, the air intake mode may change auto-
matically to the FRESH mode. This is not a
malfunction.
When the air conditioning is ON, if the engine
coolant temperature becomes extremely
high, the RECIRCULATED mode is automati-
cally selected. This is not a malfunction.
When the engine coolant temperature is low-
ered, the previous mode resumes.(d) Onoff of the air conditioning
Touch the “A/C” switch.
To turn the air conditioning on and touch it
again to turn the air conditioning off.
The air conditioning does not work if the out-
side temperature is lowered down to around
0C (32F).
If the system is used for ventilation, heating in
dry weather or removing frost or exterior fog
on the windshield, turn the air conditioning off
once it is no longer required. This will improve
fuel economy. The air conditioning can be
used for year−round automatic temperature
control including cooling and dehumidifying
operation.
If the air conditioning compressor does not
operate, the display light of the “A/C” switch
will blink. If the display light of the “A/C” switch
blinks even when the “A/C” switch is touched
again, have the compressor checked by your
nearest dealer.
If the engine coolant temperature becomes
extremely high, the air conditioning may shut
off automatically to resolve emergency situa-
tion for engine cooling. This is not a malfunc-
tion. When the engine coolant temperature is
lowered, the air conditioning comes on auto-
matically.

160
— Automatic control
SETTING OPERATION
The automatic air conditioning automati-
cally maintains the set temperature.
In the automatic operation mode, the air con-
ditioning selects the most suitable fan speed,
air flow, air intake and on−off the air condition-
ing according to the temperature.
(a) “AUTO” button
Push the “AUTO” button.
An indicator light will illuminate to show that
the automatic operation mode has been se-
lected.
You may use manual controls if you want to
select your own settings.
INFORMATION
This automatic control has additional
function as described below, when
the “AUTO” button is pushed.
The fan speed is stopped for a little
while until warm air preparation, when
outside temperature is cold like a win-
ter season in the “Floor” or “Bilevel”
air flow mode. If quick removal for ex-
terior frost, fog and inside fog on the
windshield is desired, use the high
fan speed setting after the “Wind-
shield” air flow mode has been se-
lected.
The fan speed is stopped few sec-
onds until cool air preparation, when
outside temperature is hot like a sum-
mer season in the “Panel” or “Bilev-
el” air flow mode.
The internal circulation may be ap-
plied for maximum cooling in the au-
tomatic operation mode, when out-
side temperature is hot like a summer
season.
If fresh outside air is desired into the
vehicle, push the air intake control
button to select the FRESH mode.