TOYOTA HIGHLANDER 2017 XU50 / 3.G Quick Reference Guide
Manufacturer: TOYOTA, Model Year: 2017, Model line: HIGHLANDER, Model: TOYOTA HIGHLANDER 2017 XU50 / 3.GPages: 56, PDF Size: 3.78 MB
Page 11 of 56

OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
9
NOTE: Regularly scheduled maintenance, including
oil changes, will help
extend the life of your vehicle and maintain performance. Please refer t\
o the
“Warranty & Maintenance Guide.”
NOTE: To close, tighten until one click is heard. If the cap is not tightened \
enough, Check Engine “
” indicator may illuminate.
Turn to open
The brightness level of the meters when the surroundings are bright (da\
y mode)
and dark (night mode) can be adjusted individually. However,when in da\
y mode,
adjusting the brightness level will also change the brightness level of \
night mode.
2.7 L 4-cylinder (1AR-FE) engine
3.5 L V6 (2GR-FKS) engine
Engine oil level dipstick
Engine oil level dipstick
Engine coolant reservoir
Engine coolant reservoir
Windshield washer fluid tank
Windshield washer fluid tank Engine oil filler cap
Engine oil filler cap
Fuel tank door release & cap
Hood release
Light control-Instrument cluster
Engine maintenance
2017_Highlander_QRG_V1_1.indd 911/22/16 11:28 PM
Page 12 of 56

10
Shift the shift lever to “S” position from “D” position.
+: Upshift (push and release)
-: Downshift (pull and release)
Downshifting increases power going uphill, or provides engine braking do\
wnhill. For best fuel
economy during normal driving conditions, always drive with the shift le\
ver in the “D” position.
Park*
Reverse
Neutral
Drive
N
“S” mode
With Smart Key system
* The “ENGINE START STOP”/ignition switch must be “ON” and t\
he brake pedal depressed to shift from Park.
Automatic door locks can be programmed to operate in different modes, or\
turned
OFF.
Shift position linked door locking/unlocking function
-Doors lock when shifting from Park.
-Doors unlock when shifting into Park.
Speed linked door locking function
-Doors lock when the vehicle speed goes above approximately 12 mph.
Driver’s door linked door unlocking function
-Doors unlock when the engine switch is set from “ON” to “ACC”\
or “LOCK” and
driver’s door is opened.
-(With Smart Key) Doors unlock when the “ENGINE START STOP” swit\
ch is set to OFF and driver’s door is opened.
Refer to the Owner’s Manual for more details.
Garage door openers manufactured under license from HomeLink®* can be
programmed to operate garage doors, estate gates, security lighting, etc\
.
Refer to “Garage door opener,” Section 6-4 in the Owner’s Manua\
l for more details.
For programming assistance, contact HomeLink
® at 1-800-355-3515, or visit
http://www.homelink.com.
* HomeLink ®
is a registered trademark of Gentex Corporation.
Clock
Press “H” for Hours and “M” for minutes
to set or change the time.
HoursMinutes
FEATURES & OPERATIONS
“S” (SEQUENTIAL) MODE
Auto lock/unlock
Automatic transmission
2017_Highlander_QRG_V1_1.indd 1011/22/16 11:28 PM
Page 13 of 56

OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
11
Shift the shift lever to “S” position from “D” position.
+: Upshift (push and release)
-: Downshift (pull and release)
Downshifting increases power going uphill, or provides engine braking do\
wnhill. For best fuel
economy during normal driving conditions, always drive with the shift le\
ver in the “D” position.
LockUnlock
Unlock
Lock
With Smart Key system Without Smart Key system
PushTurn
Turn
Turn
Set: Depress
Release: Depress again
* The “ENGINE START STOP”/ignition switch must be “ON” and t\
he brake pedal depressed to
shift from Park.
Automatic door locks can be programmed to operate in different modes, or\
turned
OFF.
Shift position linked door locking/unlocking function
-Doors lock when shifting from Park.
-Doors unlock when shifting into Park.
Speed linked door locking function
-Doors lock when the vehicle speed goes above approximately 12 mph.
Driver’s door linked door unlocking function
-Doors unlock when the engine switch is set from “ON” to “ACC”\
or “LOCK” and
driver’s door is opened.
-(With Smart Key) Doors unlock when the “ENGINE START STOP” swit\
ch is set to OFF and driver’s door is opened.
Refer to the Owner’s Manual for more details.
Garage door opener (HomeLink®)* (if equipped)
Garage door openers manufactured under license from HomeLink®* can be
programmed to operate garage doors, estate gates, security lighting, etc\
.
Refer to “Garage door opener,” Section 6-4 in the Owner’s Manua\
l for more details.
For programming assistance, contact HomeLink
® at 1-800-355-3515, or visit
http://www.homelink.com.
* HomeLink ®
is a registered trademark of Gentex Corporation.
HomeLink® indicator light
Garage door operation indicator
Press “H” for Hours and “M” for minutes
to set or change the time.
Auto lock/unlock
Automatic transmission
Door locks
Parking brake
Steering lock release
2017_Highlander_QRG_V1_1.indd 1111/22/16 11:28 PM
Page 14 of 56

12
Moon roof (if equipped)
Panoramic moon roof (if equipped)
FEATURES & OPERATIONS
Tilt
Close
Recommended open position to
minimize wind noise.
Push once to open partway;
again to open completely.
If the moon roof is open, pressing the switch
closes it up to the tilt-up position.
If the shade is closed past the half-open position
when the switch is pressed, it will open up to the
half-open position.
To stop operation partway, quickly slide and
release the switch again.
Close
Open
The moon roof stops slightly before the fully open position to reduce wind \
noise and the
shade opens fully. Slide the switch again to fully open or close the moon roo\
f.
Instrument panel
NOTE: If battery is disconnected, the power back door needs to be reinitialized.\
Refer to the Owner’s Manual for more details.
Open only
1. When the liftgate reaches the desired height, push the rear liftgate cl\
ose-button (on the
door jam of the liftgate) once. Press and hold the button until the buzzer \
sounds.
2. To reset the height, with the liftgate open and not moving, press and h\
old the rear liftgate close-button until it buzzes, and continue to hold until it buzzes again -then let g\
o. Push
the same button to close the liftgate. When you next open the liftgate it w\
ill open to the
maximum height.
3. The height can also be set through the “Setup” screen on the audi\
o display. Setup >
Vehicle Customization > Other Vehicle Settings > Power Back Door Opening Adjust\
.
Through this screen, there are 5 height options to choose from.
NOTE: If the liftgate has stopped operating, check inside the glove box, on t\
he left side, to ensure the PWR DOOR OFF button has not been pushed.
For detailed instructions, see Owner’s Manual.
SLIDING OPERATION
SHADE OPERATION
SLIDING OPERATION
PROGRAMMABLE POWER LIFTGATE
TILTING OPERATION
TILTING OPERATION
2017_Highlander_QRG_V1_1.indd 1211/22/16 11:28 PM
Page 15 of 56

OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
13
Door-Power Liftgate (back door) (if equipped)
If the moon roof is open, pressing the switch
closes it up to the tilt-up position.
If the shade is closed past the half-open position
when the switch is pressed, it will open up to the
half-open position.
The moon roof stops slightly before the fully open position to reduce wi\
nd noise and the
shade opens fully. Slide the switch again to fully open or close the moo\
n roof.
PushPush and hold
Instrument panel Open and close
Open: Push and hold
Close: Push and hold again
NOTE: If battery is disconnected, the power back door needs to be reinitialize\
d.
Refer to the Owner’s Manual for more details.
Open onlyRemote
control
(without
Smartkey)Remote
control
(with
Smartkey)
1. When the liftgate reaches the desired height, push the rear liftgate \
close-button (on the
door jam of the liftgate) once. Press and hold the button until the buz\
zer sounds.
2. To reset the height, with the liftgate open and not moving, press and\
hold the rear liftgate close-button until it buzzes, and continue to hold until it buzzes again\
-then let go. Push
the same button to close the liftgate. When you next open the liftgate i\
t will open to the
maximum height.
3. The height can also be set through the “Setup” screen on the au\
dio display. Setup > Vehicle Customization > Other Vehicle Settings > Power Back Door Opening\
Adjust.
Through this screen, there are 5 height options to choose from.
NOTE: If the liftgate has stopped operating, check inside the glove box,\
on the left side, to ensure the PWR DOOR OFF button has not been pushed.
For detailed instructions, see Owner’s Manual.
PROGRAMMABLE POWER LIFTGATE
TILTING OPERATION
TILTING OPERATION
2017_Highlander_QRG_V1_1.indd 1311/22/16 11:28 PM
Page 16 of 56

14
MANUAL SEAT
POWER SEAT AND DRIVING POSITION MEMORY (IF EQUIPPED)
Second row type 1
Refer to the Owner’s Manual for more details.
Hold wheel, push lever down, set angle and length, and return lever.
Angle
Lock release lever
NOTE: Do not attempt to adjust while the vehicle is in motion.
Length
(1) PullSeat positionSeat cushion length Seatback angle
Seatback angle Memory
position 1
Memory
position 2
Set memory
position
Seat position
Vertical seat Lumbar support
Seatback angle
Height Lock release button
Front
Tilt & telescopic steering wheel
Seat adjustments-Front
FEATURES & OPERATIONS
2017_Highlander_QRG_V1_1.indd 1411/22/16 11:28 PM
Page 17 of 56

OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
15
Second row type 1 Second row type 2Third row seat
Refer to the Owner’s Manual for more details.
Hold wheel, push lever down, set angle and length, and return lever.
NOTE: Do not attempt to adjust while the vehicle is in motion.
Length
Pull
(1) Pull(2) Raise
Seat position
(forward/backward)Seat position
(forward/backward)
Seatback angle Seatback angle
adjustment straps
Seatback angle
Height Lock release button Lock release button Lock release button
FrontSecond rowThird row
Height Height
Seat adjustments-Rear
Seats-Head restraints
Seats-Stowing & returning 3rd row seats
2017_Highlander_QRG_V1_1.indd 1511/22/16 11:29 PM
Page 18 of 56

16
Instrument panel
USB 2.1A12V DC
The “ENGINE START STOP”/ignition switch must be in the “ACC”\
or “ON” position to be used.
Center console (front)
Single wipeInterval wipe
Off
Push to Wash and wipe
1 Intermittent windshield wiper
frequency adjustment
Rotate to increase/decrease wipe
frequency.
2 Rain-sensing windshield wipers
Rotate to increase/decrease sensor
sensitivity. (if equipped)Temporary
operation
Rain sensing
(AUTO)Low
HighAdjust sensitivity2
Pull to wash
and wipe
Interval wipe
Mist
Slow
Fast
Adjust frequency
1
Pull to wash
and wipe
Center console (rear)
Front fog lights come on only when the headlights are on low beam.
Daytime Running Light system (DRL) (if equipped)
Automatically turns on the headlights at
a reduced intensity. Automatic light cut off system Lights automatically turn off after a delay of 30 seconds, or
when lock switch on remote is pushed after all doors are locked.
Parking lights
DRL OFF
With DRL OFF switch
12V DC
12V DC
Note: USB 2.1A for charging devices only.
HEADLIGHTS
FRONT FOG LIGHTS
TURN SIGNALS
FEATURES & OPERATIONS Windshield wipers & washers
Power outlets-
12V DC/120V AC/USB 2.1A (
if equipped)
FRONT-INTERMITTENT
FRONT-AUTO (RAIN-SENSING)
REAR
2017_Highlander_QRG_V1_1.indd 1611/22/16 11:29 PM
Page 19 of 56

OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
17
The “ENGINE START STOP”/ignition switch must be in the “ACC”\
or “ON” position to be used.
2 Rain-sensing windshield wipers
Rotate to increase/decrease sensor
sensitivity. (if equipped)
Center console (rear)
Front fog lights come on only when the headlights are on low beam.
Daytime Running Light system (DRL) (if equipped) Automatically turns on the headlights at
a reduced intensity. Automatic light cut off system Lights automatically turn off after a delay of 30 seconds, or
when lock switch on remote is pushed after all doors are locked.
Low beam
High beam
High beam flasher
Parking lights
Auto
DRL OFF
With DRL OFF switch
Headlights
Turn
Right turn
Lane change
Lane change Left turn
120V AC
12V DC
USB 2.1A
Note: USB 2.1A for charging devices only.
Lights & turn signals
HEADLIGHTS
FRONT FOG LIGHTS
TURN SIGNALS
Windshield wipers & washers
Power outlets-
12V DC/120V AC/USB 2.1A (
if equipped)
2017_Highlander_QRG_V1_1.indd 1711/22/16 11:29 PM
Page 20 of 56

18
Up
Down
Automatic operation front row or all-position (if equipped) Push the switch
completely down or pull it completely up and release to fully open or cl\
ose. To stop
the window partway, operate the switch in the opposite direction.
Window lock switch Deactivates all passenger windows. Driver’s window remains
operable.
Steering wheel telephone controls
Bluetooth
® technology allows dialing or receipt of calls without taking hands from\
the steering wheel or using a cable to connect the compatible telephone \
and
the system. Refer to “Bluetooth
® Device Pairing Section,” in this guide, for more
information about phone connections and compatibility.
* Position of buttons may vary on some vehicles, for more details please\
refer to the
Owner’s Manual.
The Stop & Start Engine System stops and restarts the engine according
to the brake pedal operation and other operations when the
vehicle is stopped.
Stopping the engine
While driving with the shift lever
in D, depress the brake pedal,
and stop the vehicle.
Disabling the Stop & Start Engine
System
Press the Stop & Start Engine System
cancel switch to disable the system.
DRIVER SIDE WINDOW LOCK SWITCH
If the engine is stopped by the Stop & Start Engine System when the vehi\
cle is
on an incline, brake force is temporarily maintained to prevent rolling
backwards until the engine is restarted and drive force is generated.
When drive force is generated, the maintained brake force is automatical\
ly
canceled.
HILL-START ASSIST CONTROL (HAC)
Volume control
Enter/Set/ResetSelect an item/
change pages
Return to the
previous screen
Press: Displays the screen registered as the top
screen
Press and hold: Registers the currently displayed
screen as the top screen
Multi-Information Display (MID)
Windows-Power
FEATURES & OPERATIONS
4.2” COLOR DISPLAY
Push MID control switches to view or change information in the following\
:
Drive information
Navigation system linked display (if equipped)
Audio system linked display
Driving assist information (if equipped)
Stop & Start Engine System information (if equipped)
Warning messages
Settings display
2017_Highlander_QRG_V1_1.indd 1811/22/16 11:29 PM