brakes TOYOTA HIGHLANDER HYBRID 2020 Owners Manual (in English)

12
(1)
Put the shift lever in “P.”
(2) Depress the brake pedal, and “
” will be displayed on the Multi-Information
Display.
(3) Press the “POWER” switch briefly and firmly.
(4) The “READY” light will blink. After a few seconds, when the light \�remains steady
and a beep sounds, shift the gear to the desired position and you may be\�gin
driving.
The Hybrid Synergy Drive System utilizes a computer-controlled gasoline \�engine
and electric motor to provide the most efficient combination of power fo\�r the
vehicle. To conserve energy, when the brakes are applied the braking for\�ce
generates electricity which is then sent to the traction battery. In add\�ition, the
engine shuts off when the vehicle is stopped. The benefits are better fu\�el economy,
reduced vehicle emissions.
NOTE: Fuel consumption and energy information of the Hybrid System are
shown on the Multi-Information Display and/or navigation system
screen (if equipped).
1. Ensure tire pressures are maintained at levels specified in the Owner’s Manual.
2. When possible, link trips to reduce engine cold starts.
3. Avoid driving at speeds that are higher than necessary, especially on\� the highway.
4. When possible, avoid sudden stops to maximize regenerative braking en\�ergy.
5. Minimize use of the Air conditioning.
FEATURES & OPERATIONS Hybrid Synergy Drive System
TIPS FOR IMPROVED FUEL ECONOMY
STARTING THE HYBRID SYSTEM

36
FEATURES & OPERATIONSRear view monitor system
(if equipped)
The rear view monitor system displays an image of the view from the bump\�er of
the rear area of the vehicle. The camera for the rear view monitor syste\�m is located
above the license plate.
To adjust the image on the rear view monitor screen, press the “MENU”\� button and
select “Display”. Select “Camera” to adjust the screen contr\�ast and brightness.
Refer to the Navigation and Multimedia System Owner’s Manual for limi\�tations and
more details on this system.
Refer to section PKSB (Parking Support Brake function) in the Owner’\�s Manual for
limitations and more details.The Front and Rear Parking Assist with Automated Braking consists of the\� following
functions that operate when driving at a low speed or backing up, such a\�s when
parking. When the system determines that the possibility of a collision \�with a
detected object is high, a warning operates to urge the driver to take e\�vasive
action. If the system determines that the possibility of a collision wit\�h a detected
object is extremely high, the brakes are automatically applied to help a\�void the
collision or help reduce the impact of the collision.
CHANGE SETTINGS
Use “”
or “” and “” of the meter control switches to select “” and
“
” in the Multi-Information Display (MID) to change settings. The system\� will
continue in the last state it was in (ON or OFF) when the engine is st\�arted again.
Front and Rear Parking Assist with
Automated Braking
(if equipped)

41
Radar sensorCamera sensor
Sensors
TSS 2.0 combines an in-vehicle camera mounted in front of the inside rea\�r view
mirror and a radar mounted in the front grille. These sensors support th\�e driver assist
systems.
The Pre-Collision System uses a radar sensor and camera sensor to help d\�etect a
vehicle or pedestrian or bicyclist in front of your vehicle.
As there is a limit to the degree of recognition accuracy and control pe\�rformance that
this system can provide, do not overly rely on this system. This system \�will not prevent
collisions or lessen collision damage or injury in every situation. Do n\�ot use PCS
instead of normal braking operations under any circumstances. Do not att\�empt to test
the operation of the Pre-Collision System yourself, as the system may no\�t operate or
engage, possibly leading to an accident. In some situations, such as whe\�n driving in
inclement weather such as heavy rain, fog, snow or a sandstorm or while \�driving on a
curve and for a few seconds after driving on a curve, a vehicle or pedes\�trian or bicyclist
may not be detected by the radar and camera sensors, preventing the syst\�em from
operating or engaging properly.
Refer to the Toyota Owner’s Manual for a list of additional situation\
s in which the
system may not operate properly.
Pre-Collision Warning
When the system determines that the possibility of a frontal collision i\�s high, a buzzer
will sound and a warning message will be displayed on the Multi-Informat\�ion Display
(MID) to urge the driver to take evasive action.
Pre-Collision Brake Assist
If the driver notices the hazard and brakes, the system may provide addi\�tional braking
force using Brake Assist. This system may prime the brakes and may apply\� greater
braking force in relation to how strongly the brake pedal is depressed.
Pre-Collision System with
Pedestrian Detection (PCS w/PD)
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES

42
TOYOTA SAFETY SENSE™
PRE-COLLISION SYSTEM (CONTINUED)
Refer to the Toyota Owner’s Manual for additional information on PCS \
operation,
settings adjustments, limitations, and precautions before attempting to \
use it. Pre-Collision Braking
If the driver does not brake in a set time and the system determines tha\�t the possibility
of a frontal collision with a preceding vehicle is extremely high, the s\�ystem may
automatically apply the brakes, reducing speed in order to help the driv\�er reduce the
impact and in certain cases avoid the collision.
Monocular camera sensorMillimeter
wave radar
As part of the Pre-Collision System, this function is also designed to f\�irst provide an
alert and then automatic braking if needed.
Refer to the Toyota Owner’s Manual for additional limitations and inf\�ormation.Under certain conditions, the PCS system included with the TSS 2.0 packa\�ge
may also help to detect a pedestrian or bicyclist in front of your vehic\�le using the
in-vehicle camera and front grille-mounted radar. The in-vehicle camera of PCS
detects a potential pedestrian or bicyclist based on size, profile, and \�motion of
the detected pedestrian or bicyclist. However, a pedestrian or bicyclist\� may not
be detected depending on the conditions, including the surrounding brigh\�tness
and the motion, posture, size, and angle of the potential detected pedes\�trian or
bicyclist, preventing the system from operating or engaging.
PCS PEDESTRIAN DETECTION

53
ADJUSTING DISTANCE
To change the vehicle-to-vehicle distance

Push the “
” button to cycle
through the settings, which will
change progressively.
This mode employs a radar sensor to detect the presence of a preceding v\�ehicle
up to approximately 328 ft (100 m) ahead, determines the current vehic\�le-to-vehicle
following distance and operates to maintain a preset following distance \�from the
vehicle ahead. These distances vary based on vehicle speed.
LONG
(default setting) MIDDLE
SHORT
Note: Vehicle-to-vehicle distance will close in when traveling on long d\�ownhill
slopes.
Preceding vehicle
mark
(1) (2) (3)
(1) Constant speed cruising when there are no vehicles ahead
The vehicle travels at the speed set by the driver. The desired vehicle-\�to-

vehicle distance can also be set by operating the vehicle-to-vehicle dis\�tance
control.
(2) Deceleration cruising and follow-up cruising when a preceding vehicle

driving slower than the set speed appears
When a vehicle is detected running ahead of you, the system automaticall\�y
decelerates your vehicle. When a greater reduction in vehicle speed is
necessary, the system applies the brakes (the brake lights will come on\� at this
time). The system will respond to changes in the speed of the vehicle a\�head
in order to maintain the vehicle-to-vehicle distance set by the driver. \�A warning
tone warns you when the system cannot decelerate sufficiently to prevent\� your
vehicle from closing in on the vehicle ahead.
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES

61
Star Safety System™
Your vehicle comes standard with the Star Safety SystemTM, which combines Anti-
lock Brake System (ABS), Brake Assist (BA), Electronic Brake-force D\�istribution
(EBD), Smart Stop Technology (SST), Traction Control (TRAC) and Ve\�hicle Stability
Control (VSC).
Refer to the Owner’s Manual for more details and important information on limitations
to these systems.
ANTI-LOCK BRAKE SYSTEM (ABS)
Toyota’s ABS sensors detect which wheels are locking up and limits wh\�eel lockup
by “pulsing” each wheel’s brakes independently. Pulsing release\�s brake pressure
repeatedly for fractions of a second. This helps the tires attain the tr\�action that
current road conditions will allow, helping you to stay in directional c\�ontrol.
BRAKE ASSIST (BA)
Brake Assist is designed to detect sudden or “panic” braking, and \�then add braking
pressure to help decrease the vehicle’s stopping distance. When there\�’s only a split
second to react, Brake Assist can add additional brake pressure more qui\�ckly than
just the driver alone can.
ELECTRONIC BRAKE FORCE DISTRIBUTION (EBD)
Toyota’s ABS technology has Electronic Brake-force Distribution (EBD\�) to help
maintain control and balance when braking. EBD responds to sudden stops \�by
redistributing brake force to enhance the braking effectiveness of all f\�our wheels.
SMART STOP TECHNOLOGY (SST)
Smart Stop Technology automatically reduces engine power when the accele\�rator
and brake pedals are pressed simultaneously under certain conditions.
SST engages when the accelerator is depressed first and the brakes are a\�pplied
firmly for longer than one-half second at speeds greater than five miles\� per hour.
SST doesn’t engage if the brake pedal is depressed before the acceler\�ator pedal,
allowing vehicles to start on a steep hill and safely accelerate without\� rolling
backward.
ENHANCED VEHICLE STABILITY CONTROL (VSC)
Enhanced Vehicle Stability Control provides cooperative control of the A\�BS, TRAC,
VSC and EPS.
Enhanced VSC helps to maintain directional stability when loss of tracti\�on occurs
during a turn.
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES

62
Floor mat installation
SAFETY AND EMERGENCY FEATURES
There are two types of Toyota floor mats: carpeted and all-weather. Each\� vehicle
has model-specific floor mats. Installation is easy.
To keep your floor mat properly positioned, follow these steps:
•
Only use Toyota floor mats designed for your specific model.
•
Use only one floor mat at a time, using the retaining hooks to keep the \�mat in place.
•
Install floor mats right side up.
TRACTION CONTROL (TRAC)
VSC helps prevent loss of traction during cornering by reducing engine p\�ower, and
Traction Control helps maintain traction on loose gravel and wet, icy, o\�r uneven
surfaces by applying brake force to the spinning wheel(s).
Toyota’s TRAC sensors are activated when one of the drive wheels star\�ts to slip.
TRAC limits engine output and applies the brakes to the spinning wheel. \�This
transfers power to the wheels that still have traction to help keep you \�on track.
Always align the Δ marks