center console TOYOTA LAND CRUISER 1986 Factory Repair Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1986, Model line: LAND CRUISER, Model: TOYOTA LAND CRUISER 1986Pages: 3115, PDF Size: 54.88 MB
Page 27 of 3115
AC1LQ-04
I08494
AC-90
- AIR CONDITIONINGAIR INLET TEMPERATURE SENSOR
2815 Author: Date:
2004 LAND CRUISER (RM1071U)
AIR INLET TEMPERATURE
SENSOR
INSPECTION
1. REMOVE FRONT SEATS
2. REMOVE REAR CONSOLE BOX
3. REMOVE FRONT CONSOLE BOX COVER
4. REMOVE LOWER CENTER CLUSTER FINISH PANEL
5. REMOVE FRONT DOOR SCUFF PLATES
6. REMOVE COWL SIDE TRIMS
7. REMOVE REAR DOOR SCUFF PATES
8. REMOVE CENTER PILLAR GARNISHES
9. REMOVE AIR INLET TEMPERATURE SENSOR
(a) Slide the floor carpet backward.
(b) Disconnect the connector.
(c) Remove the screw and the air inlet temperature sensor.
10. INSPECT AIR INLET TEMPERATURE SENSOR CIR-
CUIT (See page DI-1342)
11. INSTALL AIR INLET TEMPERATURE SENSOR
(a) Install the air inlet temperature sensor with the screw.
(b) Connect the connector.
(c) Install the floor carpet.
12. INSTALL CENTER PILLAR GARNISHES
13. INSTALL REAR DOOR SCUFF PLATES
14. INSTALL COWL SIDE TRIMS
15. INSTALL FRONT DOOR SCUFF PLATES
16. INSTALL REAR CONSOLE BOX
17. INSTALL FRONT SEATS
Page 81 of 3115
AC1LJ-04
I06818
- AIR CONDITIONINGPOWER TRANSISTOR (for Rear Heater)
AC-83
2808 Author: Date:
2004 LAND CRUISER (RM1071U)
POWER TRANSISTOR (for Rear
Heater)
INSPECTION
1. REMOVE FRONT SEATS
2. REMOVE REAR CONSOLE BOX
3. REMOVE FRONT CONSOLE BOX COVER
4. REMOVE LOWER CENTER CLUSTER FINISH PANEL
5. REMOVE FRONT DOOR SCUFF PLATES
6. REMOVE COWL SIDE TRIMS
7. REMOVE REAR DOOR SCUFF PATES
8. REMOVE CENTER PILLAR GARNISHES
9. REMOVE POWER TRANSISTOR
(a) Slide the floor carpet backward.
(b) Disconnect the connector.
(c) Remove the 2 screws and power transistor.
10. INSPECT POWER TRANSISTOR
Check the power transistor in the same way as for ºPOWER
TRANSISTOR (For Rear Cooler)º on page AC-82.
11. INSTALL POWER TRANSISTOR
12. INSTALL CENTER PILLAR GARNISHES
13. INSTALL REAR DOOR SCUFF PATES
14. INSTALL COWL SIDE TRIMS
15. INSTALL FRONT DOOR SCUFF PLATES
16. INSTALL LOWER CENTER CLUSTER FINISH PANEL
17. INSTALL FRONT CONSOLE BOX COVER
18. INSTALL REAR CONSOLE BOX
19. INSTALL FRONT SEATS
Page 102 of 3115
AC1KN-05
I15824
Cowl Side Trim
Front Door Scuff PlateCenter Pillar Garnish
Rear Door Scuff plate
Console Upper Panel
Lower Center Cluster
Finish Panel
Audio Amplifier
Front Console Box Rear Heater Unit
Rear Console
End Panel
Cooler Bracket Rear Heater Duct
Rear Console Box
- AIR CONDITIONINGREAR HEATER UNIT
AC-45
2770 Author: Date:
2004 LAND CRUISER (RM1071U)
REAR HEATER UNIT
COMPONENTS
Page 109 of 3115
AC1KO-04
I03973
I05080
Second Ridge
Hose Clip
Water Hose
I03924
- AIR CONDITIONINGREAR HEATER UNIT
AC-47
2772 Author: Date:
2004 LAND CRUISER (RM1071U)
REMOVAL
1. DRAIN ENGINE COOLANT FROM RADIATOR
HINT:
It is not necessary to drain out all the coolant.
2. DISCONNECT WATER HOSES FROM HEATER RA-
DIATOR PIPES
(a) Using pliers, grip the claws of the clip and slide the clip
along the hose
(b) Disconnect the water hoses
HINT:
At the time of installation, push the water hose on to the heater
radiator pipe to the second ridge on the pipe.
3. REMOVE FRONT SEATS
4. REMOVE REAR CONSOLE BOX
5. REMOVE FRONT CONSOLE BOX COVER
6. REMOVE LOWER CENTER CLUSTER FINISH PANEL
7. REMOVE FRONT DOOR SCUFF PLATE
8. REMOVE COWL SIDE TRIMS
9. REMOVE REAR DOOR SCUFF PLATES
10. REMOVE CENTER PILLAR GARNISHES
11. SLIDE FLOOR CARPET BACKWARD
12. REMOVE COOLER BRACKET
Remove the 4 bolts and the cooler bracket.
Page 412 of 3115
BO1KK-04
H18910
Reinforcement
Floor Brace
No. 1 BraceNo. 3 Heater to
Register Duct
Instrument PanelCenter Register
Radio With A/C Control Assembly
Front Ash Receptacle Retainer Center Lower
Cluster Finish Panel
Front Ash
Receptacle BoxLower No. 2
Panel
Glove Compartment Door
Rear Console Cup Holder Box Front
Console
Panel
Front
Console Box
Rear Console
Box
Rear Radio
Control Panel
Console Rear End Panel Combination Meter
Cluster Finish
Panel
LH Lower Panel
Lower No. 1 Panel No. 2 Heater to
Register Duct
Combination
Switch
Steering WheelSteering Wheel Pad
Front Pillar Garnish
Cowl Side Trim
Front Door Scuff Plate Front Assist Grip No. 4 Heater to
Register Duct
Front Pillar Garnish
Front Assist Grip
Cowl Side Trim
Front Door Scuff Plate
AA
A
A
BBB
C
C
C
C
CC
C
C
C
D
H
A
F
20 (204, 15)
EE
Glove Compartment
Door Damper
50 (510, 37)
BB
Rear Console BoxNo. 1 Under Cover
Console Box
Hole Cover
w/ Disc Player
Changer:
B
Column Cover
Transfer
Shift
Lever
Knob
: Specified torqueN´m (kgf´cm, ft´lbf)
H
H
H
H
I
I
EE
JJ
F
F
F
F
F
H
HH
H
H
BB
BB
HH
H
H
H
H
F
F
F
FF
D Front Console
Box bracket
- BODYINSTRUMENT PANEL
BO-81
2655 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTRUMENT PANEL
COMPONENTS
Page 416 of 3115
BO3XU-02
H21208
Center Bracket
No. 5 Heater to
Register Duct
Airbag Connector
H18914
H21406
: 5 Clips
- BODYINSTRUMENT PANEL
BO-91
2665 Author: Date:
2004 LAND CRUISER (RM1071U)
INSTALLATION
1. INSTALL REINFORCEMENT
2. INSTALL NO. 1 BRACE
3. INSTALL FLOOR BRACE
4. INSTALL GLOVE COMPARTMENT DOOR DAMPER
5. INSTALL NO. 4 HEATER TO REGISTER DUCT
6. INSTALL NO. 3 HEATER TO REGISTER DUCT
7. INSTALL ECM (See page SF-60)
8. INSTALL INSTRUMENT PANEL
HINT:
Install the airbag connector between the No. 5 heater to
register duct and the center bracket temporarily, then
install the instrument panel.
Remove the airbag connector before installing the lower
No. 2 panel.
(a) Install the 6 bolts, the 2 nuts and the instrument panel,
then connect the connectors.
(b) Install the 2 bolts to the front passenger airbag assembly.
Torque: 20 N´m (204 kgf´cm, 15 ft´lbf)
(c) Connect the junction connectors.
HINT:
The connectors can be connected by tightening the bolts.
9. INSTALL FRONT CONSOLE BOX AND FRONT CON-
SOLE BOX BRACKET
Install the front console box and the front console box bracket
with the 2 bolts.
10. INSTALL CENTER LOWER CLUSTER FINISH PANEL
Connect the connector, then install the center lower cluster fin-
ish panel.
Page 417 of 3115
H20954
H20955
: 2 Clips
H18913
H18912
: 6 Clips BO-92
- BODYINSTRUMENT PANEL
2666 Author: Date:
2004 LAND CRUISER (RM1071U)
11. INSTALL REAR CONSOLE BOX
(a) w/o Disc player changer:
Install the rear console box with the 6 bolts and the 8
screws.
(b) w/ Disc player changer:
Install the rear console box with the 4 bolts and the 8
screws.
12. INSTALL REAR RADIO CONTROL PANEL
Install the rear radio control panel with the 3 screws, then con-
nect the connector.
13. INSTALL CONSOLE REAR END PANEL
(a) Install the console rear end panel with the 2 screws.
(b) Install the rear console cup holder box.
14. INSTALL FRONT CONSOLE PANEL
Install the front console panel, then install the transfer shift lever
knob.
15. INSTALL RADIO WITH A/C CONTROL ASSEMBLY
HINT:
w/ Navigation System:
When removing/installing or replacing EMV, or when discon-
necting/connecting the battery terminal, turn the IG ON and
OFF twice for initial display setting.
16. INSTALL CENTER REGISTERS
Connect the connectors, then install the center registers.
17. INSTALL LOWER NO. 2 PANEL
Install the lower No. 2 panel with the 3 screws.
Page 425 of 3115
H18912
: 6 Clips
H18913
: 2 Clips
H20954
H20955
H21406
: 5 Clips
- BODYINSTRUMENT PANEL
BO-87
2661 Author: Date:
2004 LAND CRUISER (RM1071U)
23. REMOVE FRONT CONSOLE PANEL
(a) Remove the transfer shift lever knob.
(b) Using a screwdriver, remove the front console panel.
HINT:
Tape up the screwdriver tip before use.
24. REMOVE CONSOLE REAR END PANEL
(a) Remove the rear console cup holder box.
(b) Remove the 2 screws.
(c) Using a screwdriver, remove the console rear end panel.
HINT:
Tape up the screwdriver tip before use.
25. REMOVE REAR RADIO CONTROL PANEL
Disconnect the connector, then remove the 3 screws and the
rear radio control panel.
26. REMOVE REAR CONSOLE BOX
(a) w/o Disc player changer :
Remove the 6 bolts, the 8 screws and the rear console
box.
(b) w/ Disc player changer :
Remove the 4 bolts, the 8 screws and the rear console
box.
27. REMOVE CENTER LOWER CLUSTER FINISH PANEL
Using a screwdriver, remove the center lower cluster finish pan-
el, then disconnect the connector.
HINT:
Tape up the screwdriver tip before use.
Page 465 of 3115
BO1KP-04
H18921
Dome Light
Lens
Roof Headlining
Rear Trim
Roof Headlining Double Visor
Map Lamp
Center Pillar Garnish
Rear Mat
Set Plate
Striker Plate
Upper Roof
Side Inner Garnish Assist Grip
Cowl Side Trim Front Door Scuff Plate
Center Pillar Lower
Garnish CoverRear Door
Scuff PlateQuarter Trim PanelQuarter Trim
Jack Cover
Front Pillar Garnish Front Door
Opening TrimRear Door
Opening Trim Sun Visor
Holder
Assist Grip
Plug
Overhead
Console Box
Striker Plate
Center Pillar
Lower Garnish
Front Assist Grip
Front Assist Grip
Center Assist Gripw/ Curtain Shield Airbag:
42 (430, 31)
Adjustable
AnchorRear A/C Register
Rear A/C Register
Rear A/C Control Panel Rear A/C Register
Striker Plate
Striker Plate
Center Assist Grip
Center Assist Grip
Assist Grip
Rear
Assist Grip
x5Striker Plate
Center Assist Grip w/ Curtain Shield Airbag:
Adjustable
Anchor
Center Pillar Garnish
Center
Pillar
Garnish
: Specified torqueN´m (kgf´cm, ft´lbf)Rear Mat42 (430, 31)
Cap
Cap
Holder
rear
Assist Grip
w/ Curtain Shield Airbag:
Assist Grip
Assist Grip
Assist Grip Plug
w/ Curtain Shield Airbag:
Assist
Grip
Assist Grip Plug
Assist Grip
42 (430, 31)
Lens
Room Temperature
Sensor
BO-96
- BODYROOF HEADLINING
2670 Author: Date:
2004 LAND CRUISER (RM1071U)
ROOF HEADLINING
COMPONENTS
Page 470 of 3115
H05268
H05270
H21423
4 Clips
H18926
BO-100
- BODYROOF HEADLINING
2674 Author: Date:
2004 LAND CRUISER (RM1071U)
25. REMOVE DOME LIGHT
(a) Using a screwdriver, remove the lens as shown in the il-
lustration.
HINT:
Tape up the screwdriver tip before use.
(b) Remove the 4 screws and the dome light, then disconnect
the connector.
26. REMOVE MAP LAMP
(a) Using a screwdriver, remove the lens as shown in the il-
lustration.
HINT:
Tape up the screwdriver tip before use.
(b) Remove the 4 screws and the map lamp, then disconnect
the connector.
27. REMOVE OVERHEAD CONSOLE BOX
(a) Remove the bolt.
(b) Using a screwdriver, remove the overhead console box,
then disconnect the connector.
HINT:
Tape up the screwdriver tip before use.
28. REMOVE REAR A/C CONTROL PANEL
Using a screwdriver, release the 4 claws and pull out the rear
A/C control panel, then disconnect the connector.
HINT:
Tape up the screwdriver tip before use.
29. REMOVE ROOM TEMPERATURE SENSOR
Using a scrwedriver, pull out the room temperature sensor, then
disconnect the connector.
HINT:
Tape up the screwdriver tip before use.
30. REMOVE ASSIST GRIPS
31. w/o Curtain Shield Airbag:
REMOVE CENTER ASSIST GRIPS
32. REMOVE ROOF HEADLINING
Using a clip remover, remove the 3 clips and the roof headlining.
33. REMOVE REAR A/C REGISTER
34. w/ Curtain Shield Airbag:
REMOVE ADJUSTABLE ANCHOR
Remove the 2 bolts and the adjustable anchor.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
35. w/ Curtain Shield Airbag:
REMOVE CENTER ASSIST GRIPS