Instrument TOYOTA LAND CRUISER 1996 J80 User Guide

−
BODY INSTRUMENT PANEL
BO−77
1996 LAND CRUISER (RM451U)
15. REMOVE CENTER CLUSTER FINISH PANEL WITH
HEATER CONTROL ASSEMBLY
(a) Using a screwdriver, take off the 2 claws, then remove the
cup holder hole cover.
HINT:
Tape the screwdriver tip before use.
(b) Take off the ashtray.
(c) Remove the center cluster finish panel with heater control
assembly, then disconnect the connectors.
(d) Remove the 2 screws and heater control assembly from the center cluster finish panel.
16. REMOVE RADIO
17. REMOVE GLOVE COMPARTMENT DOOR
18. REMOVE SPEAKER PANEL AND SPEAKER
19. REMOVE FRONT AND REAR CONSOLE BOX
20. DISCONNECT AIRBAG CONNECTOR
(a) Remove the airbag connector from the airbag bracket.
NOTICE:
When handling the airbag connector , take care not to dam-
age the airbag wire harness.
(b) Disconnect the airbag connector.
21. REMOVE INSTRUMENT PANEL
(a) Remove the 5 screws and 9 bolts.
(b) Remove the instrument panel. Torque: 20 N·m (210 kgf·cm, 15 ft·lbf) for passenger
airbag bolts
22. REMOVE INSTRUMENT PANEL REINFORCEMENT
(a) Remove the 2 bolts and lower instrument panel reinforce-
ment.
(b) Remove the 2 bolts, 2 nuts and No. 1 brace.
(c) Remove the 4 bolts, 4 nuts and instrument panel rein- forcement.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO399−01
BO−78
−
BODY INSTRUMENT PANEL
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE GLOVE COMPARTMENT DOOR RE- INFORCEMENT
2. REMOVE NO. 4 HEATER TO REGISTER DUCT
3. REMOVE NO. 5 HEATER TO REGISTER DUCT
4. REMOVE NO. 2 REGISTER
5. REMOVE GLOVE COMPARTMENT DOOR LOCK STRIKER PLATE
6. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY (See page RS−22 )
(a) Remove the 4 bolts and 2 nuts, and remove front passen-
ger airbag assembly.
(b) Pry up the 6 clips shown in the illustration and remove the airbag door.
CAUTION:
Do not store the front passenger airbag assembly
with the airbag deployment direction facing down.
Never disassemble the front passenger airbag as-
sembly.
7. REMOVE NO. 3 CONSOLE MOUNTING BRACKET
8. REMOVE NO. 1 HEATER TO REGISTER DUCT
9. REMOVE NO. 2 STAY
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO39A−01
−
BODY INSTRUMENT PANEL
BO−79
1996 LAND CRUISER (RM451U)
REASSEMBLY
Reassembly is in the reverse order of disassembly (See page BO−78 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BO39B−01
BO−80
−
BODY INSTRUMENT PANEL
1996 LAND CRUISER (RM451U)
INSTALLATION
Installation is in the reverse order of removal (See page BO−76 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FI0534
DI5OU−02
P22892DLC3TOYOTA
−Hand− Held Tester
−
DIAGNOSTICS ENGINE
DI−3
1996 LAND CRUISER (RM451U)
PRE−CHECK
1. DIAGNOSIS SYSTEM
(a) Description
When troubleshooting OBD II vehicles, the only dif-
ference from the usual troubleshooting procedure
is that you connect to the vehicle the OBD II scan
tool complying with SAE J1978 or TOYOTA hand −
held tester, and read off various data output from
the vehicle’s ECM.
OBD II regulations require that the vehicle’s on −
board computer lights up the Malfunction Indicator
Lamp (MIL) on the instrument panel when the com-
puter detects a malfunction in the computer itself or
in drive system components which affect vehicle
emissions. In addition to the MIL lighting up when
a malfunction is detected, the applicable Diagnostic
Trouble Codes (DTC) prescribed by SAE J2012 are
recorded in the ECM memory (See page DI−13).
If the malfunction does not reoccur in 3 trips, the MIL goes off
but the DTC remain recorded in the ECM memory.
To check the DTC, connect the OBD II scan tool or
TOYOTA hand−held tester to Data Link Connector
3 (DLC3) on the vehicle. The OBD II scan tool or
TOYOTA hand−held tester also enables you to
erase the DTCs and check freezed frame data and
various forms of engine data (For operating instruc-
tions, see the OBD II scan tool’s instruction book.).
DTC include SAE controlled codes and manufac-
turer controlled codes. SAE controlled codes must
be set as prescribed by the SAE, while manufactur-
er controlled codes can be set freely by the
manufacturer within the prescribed limits (See DTC
chart on page DI−13).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22215
−
DIAGNOSTICS ENGINE
DI−5
1996 LAND CRUISER (RM451U)
Terminal No.
Connection / Voltage or ResistanceCondition
2Bus 
Line / Pulse generationDuring transmission
4Chassis Ground / ↔ Body Ground 1 Ω or lessAlways
5Signal Ground / ↔ Body Ground 1 Ω or lessAlways
16Battery Positive / ↔ Body Ground 9 − 14 VAlways
HINT:
If your display shows ”UNABLE TO CONNECT TO VEHICLE”
when you have connected the cable of the OBD II scan tool or
TOYOTA hand−held tester to DLC3, turned the ignition switch
ON and operated the scan tool, there is a problem on the ve-
hicle side or tool side.
If communication is normal when the tool is connected to
another vehicle, inspect DLC3 on the original vehicle.
If communication is still not possible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool’s instruction manual.
2. INSPECT DIAGNOSIS (NORMAL MODE)
(a) Check the MIL. (1) The MIL comes on when the ignition switch is turnedON and the engine is not running.
HINT:
If the MIL does not light up, troubleshoot the combination meter
(See page BE−2 ).
(2) When the engine started, the MIL should go off. If the lamp remains on, the diagnosis system has de-
tected a malfunction or abnormality in the system
(b) Check the DTC.
NOTICE:
TOYOTA hand−held tester only: When the diagnosis sys-
tem is switched from normal mode to check mode, it
erases all DTCs and freezed frame data recorded in normal
mode. So before switching modes, always check the DTCs
and freezed frame data, and note them down (1) Prepare the OBD II scan tool (complying with SAE
J 1978) or TOYOTA hand−held tester.
(2) Connect the OBD II scan tool or TOYOTA hand− held tester to DLC3 in the fuse box at the lower left
of the instrument panel.
(3) Turn the ignition switch ON and switch the OBD II
scan tool or TOYOTA hand −held tester switch ON.
(4) Use the OBD II scan tool or TOYOTA hand−held tester to check the DTC and freezed frame data,
note them down. (For operating instructions, see
the OBD II scan tool’s instruction book.)
(5) See page DI−13 to confirm the details of the
DTCs.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FI3605
ON
OFF Flashing
0.13 Second
DI−6
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
NOTICE:
When simulating symptoms with an OBD II scan tool (ex-
cluding TOYOTA hand −held tester) to check the DTC, use
normal mode. For codes on the DTC chart subject to ”2 trip
detection logic”, turn the ignition switch OFF after the
symptom is simulated the first time. Then repeat the simu-
lation process again. When the problem has been simu-
lated twice, the MIL lights up and the DTCs are recorded in
the ECM.
3. INSPECT DIAGNOSIS (CHECK MODE)
HINT:
TOYOTA hand−held tester only:
Compared to the normal mode, the check mode has an in-
creased sensitivity to detect malfunctions.
Furthermore, the same diagnostic items which are detected in
the normal mode can also be detected in the check mode.
(a) Check the DTC. (1) Initial conditions
Battery positive voltage 11 V or more.
Throttle valve fully closed.
Transmission in ”park” or ”neutral” position.
Air conditioning switched OFF.
(2) Turn ignition switch OFF.
(3) Prepare the TOYOTA hand−held tester.
(4) Connect the TOYOTA hand−held tester to DLC3 in
the fuse box at the lower left of the instrument panel.
(5) Turn the ignition switch ON and push the TOYOTA hand−held tester ON.
(6) Switch the TOYOTA hand −held tester normal mode
to check mode (Check that the MIL flashes.).
(7) Switch the engine (The MIL goes out after the en- gine start.).
(8) Simulate the conditions of the malfunction de- scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTC, etc. (9) After simulating the malfunction conditions, use theTOYOTA hand−held tester diagnosis selector to
check the DTCs and freezed frame data, etc.
HINT:
Take care not to turn the ignition switch OFF. T urning the ignition
switch OFF switches the diagnosis system from check mode to
normal mode, so all DTCs, etc. are erased.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OV−03
−
DIAGNOSTICS ENGINE
DI−13
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to \
the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, che\
ck the circuit for that code listed
in the table below. For details of each code, turn to the page referred to under the ’’See page ’’ for the respe-
cire ’’DTC No.’’ in the DTC chart.
DTC No.
(See Page)Detection ItemTrouble AreaMILMemory
P0100
( DI−20 )Mass Air Flow Circuit
MalfunctionOpen or short in mass air flow meter circuit
 Mass air flow meter
 ECM
 *1
P0101
( DI−25 )Mass Air Flow Circuit
Range/Performance
Problem
Mass air flow meter *1
P0110
( DI−26 )Intake Air Temp. Circuit
MalfunctionOpen or short in intake air temp. sensor circuit
 Intake air temp. sensor
 ECM
 *1
P0115
( DI−30 )Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
 Engine coolant temp. sensor
 ECM
 *1
P0116
( DI−34 )Engine Coolant Temp. Circuit
Range/Performance ProblemEngine coolant temp. sensor
 Cooling system *1
P0120
( DI−35 )Throttle/Pedal Position
Sensor/Switch ”A” Circuit
MalfunctionOpen or short in throttle position sensor circuit
 Throttle position sensor
 ECM
 *1
P0121
( DI−39 )Throttle/Pedal Position
Sensor/Switch ”A” Circuit
Range/Performance Problem
Throttle position sensor *1
P0125
( DI−40 )Insufficient Coolant Temp. for
Closed Loop Fuel Control Open or short in heated oxygen sensor circuit
 Heated oxygen sensor *1
P0130
( DI−43 )Heated Oxygen Sensor Circuit
Malfunction (Bank 1 Sensor 1)Heated oxygen sensor
 Fuel trim malfunction *1
P0133
( DI−46 ) Heated Oxygen Sensor Circuit
Slow Response
(Bank 1 Sensor 1)
Heated oxygen sensor *1
P0135
( DI−47 ) Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 1)Open or short in heater circuit of heated oxygen sensor
 Heated oxygen sensor heater
 ECM
 *1
P0136
( DI−49 )Heated Oxygen Sensor Circuit
Malfunction
(Bank 1 Sensor 2)
Heated oxygen sensor *1
P0141
( DI−47 ) Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 2)
Same as DTC No. P0135 *1
*1: MIL lights up
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00201
ON
BE6653
P24652
DI−22
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Connect the OBD II scan tool or TOYOTA hand −held tester, and read value of
mass air flow rate.
PREPARATION:
(a) Remove the fuse cover on the instrument panel.
(b) Connect the OBD II scan tool or TOYOTA hand−held tester to the DLC3.
(c) Turn ignition switch ON and OBD II scan tool or TOYOTA hand−held tester main switch ON.
(d) Start the engine.
CHECK:
Read mass air flow rate on the OBD II scan tool or TOYOTA hand−held tester.
RESULT:
Type IType II
Mass air flow rate (gm/sec.)Approx. 0 gm/sec.439.0 gm/sec. or more
Type I Go to step 2.
Type II Go to step 5.
2 Check voltage of mass air flow meter power source.
PREPARATION:
(a) Disconnect the mass air flow meter connector.
(b) Turn ignition switch ON.
CHECK:
Measure voltage between terminal 1 of mass air flow meter con-
nector and body ground.
OK:
Voltage: 9 − 14 V
NG Check for open in harness and connector between EFI main relay (Marking: EFI) and
mass air flow meter (See page IN−28 ).
OK
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P24653
VG
(+)
(−)
−
DIAGNOSTICS ENGINE
DI−23
1996 LAND CRUISER (RM451U)
3 Check voltage between terminal VG of ECM and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel
(See page SF−65).
(b) Start the engine.
CHECK:
Measure voltage between terminal VG of ECM and body
ground while engine is idling.
OK:
Voltage:
1.1 − 1.5 V (P or N position and A/C switch OFF)
OK Check and replace ECM (See page IN−28 ).
NG
4 Check for open and short in harness and connector between mass air flow \
meter and ECM (See page IN−28 ).
NG Repair or replace harness or connector.
OK
Replace mass air flow meter.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010