damper TOYOTA LAND CRUISER 1996 J80 User Guide

SR16T−01
−
STEERING STEERING LINKAGE
SR−47
1996 LAND CRUISER (RM451U)
INSTALLATION
HINT:
When connecting the ball stud to the arm or rod, remove the
grease on the joint surfaces.
1. INSTALL TIE ROD ENDS AND RELAY ROD ENDS
(a) Turn the tie rod ends or relay rod ends equal amounts into
the rod tube. Tie rod assembly should be approximately
1,233 mm (48.54 in.). Relay rod assembly should be
approximately 1,090 mm (42.91 in.).
(b) The remaining length of threads on both tie rod ends or relay rod ends should be equal.
(c) Temporarily tighten the tie rod end or relay rod end clamps.
2. INSTALL TIE ROD ASSEMBLY
(a) Connect the tie rod assembly to the RH and LH knuckle arms.
(b) Torque the 2 nuts. Torque: 91 N·m (925 kgf·cm, 67 ft·lbf)
(c) Install 2 new cotter pins.
(d) After adjusting toe−in, torque the clamp bolts and nuts. Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
3. INSTALL RELAY ROD ASSEMBLY
(a) Connect the relay rod assembly to the knuckle arm.
(b) Torque the nut. Torque: 91 N·m (925 kgf·cm, 67 ft·lbf)
(c) Install a new cotter pin.
(d) Torque the clamp bolts and nuts. Torque: 37 N·m (375 kgf·cm, 27 ft·lbf)
4. INSTALL STEERING DAMPER
(a) Secure the damper bracket in a vise.
(b) Connect the damper to the damper bracket.
(c) Torque a new nut. Torque: 74 N·m (750 kgf·cm, 54 ft·lbf)
5. INSTALL STEERING DAMPER WITH STEERING DAMPER BRACKET
(a) Connect the damper with damper bracket to the relay rod
assembly.
(b) Torque a new nut and 2 damper bracket set bolts.
Torque:
Nut: 74 N·m (750 kgf·cm, 54 ft·lbf)
Bolt: 39 N·m (400 kgf·cm, 29 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
SS−5
128
Author: Date:
1996 LAND CRUISER (RM451U)
Camshaft
Thrust clearance
STD
Maximum
Journal oil clearance STD
Maximum
Journal diameter
Circle runout Maximum
Cam lobe height STD
Minimum
Camshaft gear backlash STD
Maximum
Camshaft gear spring end free distance0.030 − 0.080 mm (0.0012 − 0.0031 in.)
0.10 mm (0.0039 in.)
0.025 − 0.062 mm (0.0010 − 0.0024 in.)
0.10 mm (0.0039 in.)
26.959 − 26.975 mm (1.0614 − 1.0620 in.)
0.06 mm (0.0024 in.)
50.61 − 50.71 mm (1.9925 − 1.9965 in.)
50.51 mm (1.9886 in.)
0.020 − 0.200 mm (0.0008 − 0.0079 in.)
0.30 mm (0.0188 in.)
18.2 − 18.8 mm (0.712 − 0.740 in.)
Spark plug tubeProtrusion45.5 mm (1.791 in.)
Oil pump drive
shaft gearThrust clearance STD
Maximum0.040 − 0.160 mm (0.0016 − 0.0063 in.)
0.30 mm (0.0188 in.)
Chain and timing
gearChain length at 16 links Maximum
Camshaft timing gear wear (w/ Chain) Minimum
Crankshaft timing gear wear (w/ Chain) Minimum146.6 mm (5.772 in.)
126.0 mm (4.961 in.)
65.4 mm (2.575 in.)
Chain tensioner
slipper and vibra-
tion damperWearMaximum1.0 mm (0.039 in.)
Cylinder blockCylinder head surface warpageMaximum
Cylinder bore diameter STD Mark 1
2
3
Maximum STD
O/S 0.50
O/S 1.00
Main bearing bolt outside diameter STD
Minimum0.05 mm (0.0020 in.)
100.000 − 100.010 mm (3.9370 − 3.9374 in.)
100.010 − 100.020 mm (3.9374 − 3.9378 in.)
100.020 − 100.030 mm (3.9378 − 3.9382 in.)
100.23 mm (3.9461 in.)
100.73 mm (3.9658 in.)
101.23 mm (3.9854 in.)
10.85 − 11.00 mm (0.4271 − 0.4331 in.)
10.6 mm (0.417 in.)
Piston and piston
ringPiston diameter STD Mark 1
2
3
O/S 0.50
O/S 1.00
Piston oil clearance STD
Piston ring groove clearance No. 1
No. 2
Piston ring end gap STD No. 1
No. 2
Oil
Maximum No. 1 No. 2Oil99.950 − 99.960 mm (3.9350 − 3.9354 in.)
99.960 − 99.970 mm (3.9354 − 3.9358 in.)
99.970 − 99.980 mm (3.9358 − 3.9362 in.)
100.450 − 100.480 mm (3.9547 − 3.9559 in.)
100.950 − 100.980 mm (3.9744 − 3.9756 in.)
0.040 − 0.060 mm (0.0016 − 0.0024 in.)
0.040 − 0.080 mm (0.0016 − 0.0031 in.)
0.300 − 0.070 mm (0.0012 − 0.0028 in.)
0.300 − 0.520 mm (0.0118 − 0.0205 in.)
0.450 − 0.670 mm (0.0177 − 0.0264 in.)
0.150 − 0.520 mm (0.0059 − 0.0205 in.)
1.12 mm (0.0441 in.)
1.17 mm (0.0461 in.)
1.12 mm (0.0441 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EP−01
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
SS−7
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Distributor x Cylinder head1818013
No. 1 engine hanger x Cylinder head4142030
No. 2 engine hanger x Cylinder head4142030
Air intake chamber x Intake manifold2121015
Intake manifold x Cylinder head2121015
Heater inlet pipe x Intake manifold2121015
EGR pipe x Cylinder head2121015
EGR pipe x EGR valve Union nut7880058
Water outlet x Cylinder head2121015
Generator bracket x Cylinder head4344032
Cylinder head x Cylinder block 1st
2nd 3rd39
Turn 90°
Turn 90°400
Turn 90°
Turn 90°29
Turn 90°
Turn 90°
Cylinder head x Timing chain cover2121015
Camshaft bearing cap x Cylinder head1616012
Camshaft timing gear x Camshaft7475054
Chain tensioner x Cylinder head2121015
Water bypass outlet x Cylinder head2121015
Heater pipe x Timing chain cover2121015
Heater pipe x Cylinder head2020014
Exhaust manifold x Cylinder head3940029
Heat insulator x Exhaust manifold1919514
Front exhaust pipe x Exhaust manifold6363046
No. 1 support bracket x Transmission2424017
No. 1 support bracket clamp bolt19.519514
Front exhaust pipe x Rear TWC4647034
No. 2 water bypass pipe x Cylinder head2020014
No. 2 water bypass pipe x No. 1 engine hanger2020014
Fuel inlet hose x Fuel filter2930022
Intake manifold stay x Air intake chamber3636026
Intake manifold stay x Cylinder block3636026
Oil dipstick guide x Intake manifold2020014
Oil dipstick guide x No. 1 oil pan2020014
PS reservoir tank x Air intake chamber2020014
Oil jet x Cylinder block2020014
Vibration damper x Cylinder block2020014
Chain tensioner slipper x Cylinder block6970051
Timing chain cover x Cylinder block2121015
Drive belt idler pulley x Timing chain cover4344032
Crankshaft pulley x Crankshaft4124,200304
Transmission housing x No. 1 oil pan7273053
Oil level sensor x No. 1 oil pan5.45548 in.·lbf
Water pump x Cylinder block2121015
Radiator pipe x No. 1 oil pan2121015
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS−8
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
1996 LAND CRUISER (RM451U)
A/C compressor bracket x No. 1 oil pan
3737527
A/C compressor bracket x Cylinder block3737527
A/C compressor x A/C compressor bracket2525018
Oil check valve x Cylinder block2525018
Main bearing cap x Cylinder block
1st
2nd74
Turn 90°750
Turn 90°54
Turn 90°
Connecting rod cap x Connecting rod 1st
2nd48
Turn 90°490
Turn 90°35
Turn 90°
Rear oil seal retainer x Cylinder block2121015
Oil cooler cover x Cylinder block2121015
LH engine mounting bracket x Cylinder block6970051
LH insulator x LH engine mounting bracket7273043
RH engine mounting bracket x Cylinder brock6970051
RH insulator x RH engine mounting bracket7273043
PS pump x Cylinder block3637027
Knock sensor x Cylinder block4445033
Oil filter union x Cylinder block4445033
Drive plate x Crankshaft1001,00074
Transmission x Cylinder block7273053
Transmission x No. 1 oil pan7273053
Torque converter clutch x Drive plate5555041
A/T oil cooler pipe x Union (Transmission)3435025
Starter x Transmission3940029
Frame crossmember x Frame6162045
Frame crossmember x Engine rear mounting insulator7475054
Engine front mounting insulator x Frame7475054
Transfer shift lever x Transmission1818513
Transmission shift lever assembly x Body5.45548 in.·lbf
Transmission control rod x Control shaft lever131309
Front propeller shaft x Front dif ferential7475054
Front propeller shaft x Transfer7475054
Rear propeller shaft x Rear differential8890065
Rear propeller shaft x Transfer8890065
Stabillizer bar bracket mounting bolt1818513
Stabillizer bar x Axle carrier2526019
PS pressure hose x PS pump5657542
Rear TWC x Center pipe4040029
Center pipe x Tailpipe4040029
Heated oxygen sensor (Bank 1 sensor 1) x Front exhaust pipe2020014
Heated oxygen sensor (Bank 1 sensor 2) x Center pipe2020014
No. 2 support bracket x Frame18.518513
No. 3 support bracket x Frame18.518513
No. 4 support bracket x Frame18.518513
Exhaust pipe damper x Tailpipe19.519514
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1E9−02
−
SERVICE SPECIFICATIONS TRANSFER
SS−27
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Oil pump plate and separator x Rear extension housing4.95043 in.·lbf
Oil pump cover x Rear extension housing4.95043 in.·lbf
Lever lock pin121209
Oil strainer x Rear case4.95043 in.·lbf
Oil receiver x Front case121209
Case cover x Rear case3738027
Rear extension housing x Rear case3738027
Front extension housing x Front case3738027
Center differential lock Indicator switch3738014
L4 position switch3738027
Neutral position switch3738027
Screw plug x Front case1919014
Screw plug x Rear extension housing2930022
Motor actuator x Front case1818513
Differential front case x Differential rear case
Temporarily tighten98
881,00090072
65
Front case x Rear case3738027
Rear case x Retainer3940028
Dynamic damper x Rear extension housing3738027
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EH−02
SS−38
−
SERVICE SPECIFICATIONS STEERING
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
TILT STEERING COLUMN
Steering wheel set nut3435025
Steering wheel pad set screw (T orx screw)9.09078 in.·lbf
Steering column assembly set nut and bolt2525018
Sliding yoke sub−assembly x Worm gear valve body shaft3435025
Sliding yoke sub −assembly x Intermediate No. 2 shaft3435025
Universal joint x Intermediate No. 2 shaft3435025
Main shaft assembly x Universal joint3435025
Turn signal bracket set bolt4.95043 in.·lbf
Tilt sub lever side pawl set bolt x Nut5.96052 in.·lbf
Tilt lever retainer set nut1515011
Tilt lever assembly set bolt2.93026 in.·lbf
Compression spring set bolt7.88069 in.·lbf
Column hole cover x Lower dust seal5.96052 in.·lbf
Column hole cover x Body131309
Link joint protector set bolt121209
PS VANE PUMP
Pressure feed tube set union bolt5657542
PS vane pump assembly set nut3637027
Suction port union set bolt131309
Vane pump drive gear set nut7475054
Pressure port union6970051
PS GEAR
Pressure tube x Gear housing assembly for use with SST
for use without SST36
44365
45026
33
Return tube x Gear housing assembly for use with SST
for use without SST36
44365
45026
33
Gear housing assembly x Body1421,450105
Pitman arm x Cross shaft1771,800130
Cross shaft adjusting screw set nut4647034
Side cover x Gear housing6162045
Plunger guide nut2020515
Worm gear valve body assembly x Gear housing6162045
Control valve shaft x Sliding york sub −assembly3435025
STEERING LINKAGE
Pitman arm x Cross shaft1771,800130
Pitman arm x Relay rod9192567
Tie rod clamp bolt3737527
Tie rod x Knuckle arm9192567
Relay rod x Steering damper7475054
Steering damper x Steering damper bracket7475054
Steering damper bracket x Body7475054
Relay rod clamp bolt3737527
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0B2−01
Q08382
Dynamic Damper
Rear Case 
Vehicle Speed Sensor
Driven Gear
Center Differential Assembly
Bearing Race
Bearing Race L4 Position Switch
Neutral Position Switch
x 9

Rear
Extension
Housing
Oil Strainer Case Cover
x 5 
Shift Fork No.1
Bearing Race
Idler Gear Assembly
Motor Actuator
Shift Outer Lever
Output Gear
Snap Ring
Shift Fork No.2 Shaft Shift Fork No.2
Center Diff Lock
Indicator Switch
Lever Lock Pin
Washer
 Oil Seal
Shift Inner Lever
Oil Receiver
Breather Hose
Front Case Snap Ring
Shift Fork No.1 Shaft
 Non− reusable part
 Precoated part Front Extension Housing
Clutch Sleeve 
Oil Seal
Bearing Race

Slotted
Spring Pin
Input Shaft Assemblyx 5
x 8 
Retainer
Adjusting Shim
 Screw Plug
Spring
Ball
−
TRANSFER TRANSFER ASSEMBLY
TR−3
813
Author: Date:
1996 LAND CRUISER (RM451U)
TRANSFER ASSEMBLY
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0CM−01
Q07105
Q07124
FIPG
TR−4
−
TRANSFER TRANSFER ASSEMBLY
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE BREATHER HOSE
2. REMOVE DYNAMIC DAMPER
Remove the 2 bolts and dynamic damper.
HINT:
At the time of reassembly, apply adhesive to the bolt threads. Adhesive: Part No.08833 −00070, THREE BOND 1324
or equivalent
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
3. REMOVE MOTOR ACTUATOR
Remove the 4 bolts and motor actuator.
HINT:
At the time of reassembly, please refer to the following items.
Set the motor actuator in differential lock condition.
Apply FIPG to the front case.
FIPG: Part No. 08826−00090, THREE BOND 1281 or
equivalent
Torque: 18 N·m (185 kgf·cm, 13 ft·lbf)
4. REMOVE OUTPUT GEAR FROM FRONT CASE
HINT:
At the timie of reassembly apply gear oil to the output gear.
NOTICE:
At the time of reassembly, do not turn the output gear.
5. REMOVE SCREW PLUG, SPRING AND BALL
(a) Using a torx socket wrench (T40), remove the screw plug.
HINT:
At the time of reassembly, apply liquid sealer to the screw plug. Sealant: Part No.08833−00080, THREE BOND 1344,
LOCTITE 242 or equivalent
Torque:19 N·m (190 kgf·cm, 14 ft·lbf)
(b) Using a magnetic finger, remove the spring and ball.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010