cruise control TOYOTA LAND CRUISER 1996 J80 Workshop Manual

SS1EF−02
SS−36
−
SERVICE SPECIFICATIONS BRAKE
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Master cylinder x Piston stopper bolt101007
Master cylinder x Reservoir1.717.515.2 in.·lbf
Master cylinder x Brake booster131309
Brake line union nut1515511
Brake booster clevis lock nut2526019
Brake booster x Pedal bracket131309
Bleeder plug1111 08
Front disc brake caliper installation bolt1231,25090
Front disc brake caliper x Flexible hose3031022
Parking brake bellcrank x Backing plate131309
Rear disc brake cliper x Spindle pin8890065
Rear disc brake caliper x Flexible hose3031022
Rear disc brake torque plate x Knuckle1031,05076
LSP & BV bracket x Frame2526019
LSP & BV x LSP & BV bracket131309
LSP & BV spring x LSP & BV bracket1818513
LSP & BV spring x Shackle No. 11818513
LSP & BV shackle lock nut2525018
LSP & BV shackle x Shackle bracket131309
LSP & BV shackle bracket x Rear axle housing1919514
ABS actuator assembly x Body1919514
ABS actuator x Actuator bracket5.45548 in.·lbf
ABS control relay x Actuator bracket131309
Front speed sensor installation bolt1818513
Rear speed sensor installation bolt1818513
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EH−02
SS−38
−
SERVICE SPECIFICATIONS STEERING
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
TILT STEERING COLUMN
Steering wheel set nut3435025
Steering wheel pad set screw (T orx screw)9.09078 in.·lbf
Steering column assembly set nut and bolt2525018
Sliding yoke sub−assembly x Worm gear valve body shaft3435025
Sliding yoke sub −assembly x Intermediate No. 2 shaft3435025
Universal joint x Intermediate No. 2 shaft3435025
Main shaft assembly x Universal joint3435025
Turn signal bracket set bolt4.95043 in.·lbf
Tilt sub lever side pawl set bolt x Nut5.96052 in.·lbf
Tilt lever retainer set nut1515011
Tilt lever assembly set bolt2.93026 in.·lbf
Compression spring set bolt7.88069 in.·lbf
Column hole cover x Lower dust seal5.96052 in.·lbf
Column hole cover x Body131309
Link joint protector set bolt121209
PS VANE PUMP
Pressure feed tube set union bolt5657542
PS vane pump assembly set nut3637027
Suction port union set bolt131309
Vane pump drive gear set nut7475054
Pressure port union6970051
PS GEAR
Pressure tube x Gear housing assembly for use with SST
for use without SST36
44365
45026
33
Return tube x Gear housing assembly for use with SST
for use without SST36
44365
45026
33
Gear housing assembly x Body1421,450105
Pitman arm x Cross shaft1771,800130
Cross shaft adjusting screw set nut4647034
Side cover x Gear housing6162045
Plunger guide nut2020515
Worm gear valve body assembly x Gear housing6162045
Control valve shaft x Sliding york sub −assembly3435025
STEERING LINKAGE
Pitman arm x Cross shaft1771,800130
Pitman arm x Relay rod9192567
Tie rod clamp bolt3737527
Tie rod x Knuckle arm9192567
Relay rod x Steering damper7475054
Steering damper x Steering damper bracket7475054
Steering damper bracket x Body7475054
Relay rod clamp bolt3737527
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EJ−02
SS−40
−
SERVICE SPECIFICATIONS BODY ELECTRICAL
163
Author: Date:
1996 LAND CRUISER (RM451U)
BODY ELECTRICAL
SERVICE DATA
TURN SIGNAL FLASHER
Flashes/Minute60 − 120
SPEEDOMETER (USING A SPEEDOMETER)
Standard indication (mph)Allowable range (mph)
2018 − 24
4038 − 44
6058 − 66
8078 − 88
10098 − 11 0
12011 8 − 132
TACHOMETER (ON− VEHICLE) DC 13.5 V 25°C (77° F)
Standard indication (RPM)Allowable range (RPM)
700630 − 770
1,000900 − 1,100
2,0001,875 − 2,125
3,0002,850 − 3,150
4,0003,850 − 4,150
5,0004,850 − 5,150
FUEL RECEIVER GAUGE
A − B85.5 − 105.5 Ω
A − C126 − 150 Ω
B − C90 − 110 Ω
FUEL SENDER GAUGE
Float position F: Approx. 15 mm ((0.59 in.)Approx. 3 Ω
Float position E: Approx. 200 (7.87 in.)Approx. 110 Ω
ENGINE COOLANT TEMPERATURE RECEIVER GAUGE
A − B71 − 79 Ω
A − C117 − 141 Ω
B − C185 − 215 Ω
OIL PRESSURE RECEIVER GAUGE
Resistance40 − 48 Ω
CRUISE CONTROL SWITCH
Switch position OFFNo continuity
Switch position RESUME/ACCELApprox. 68 Ω
Switch position SET/COASTApprox. 198 Ω
Switch position CANCELApprox. 418 Ω
CRUISE CONTROL ACTUATOR
1 − 3Approx. 2 kΩ
2 − 3Approx. 0.5 − 1.7 kΩ
Actuator control arm free play0 mm (0 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BH−01
Q08383
Center Differential Control
Couping Assembly
Snap ring Vehicle Speed sensor
Drive Gear Ball Bearing
 Snap Ring
Snap Ring
Oil Pump Plate
Drive Rotor
Oil Pump Cover
Rear Extension housing
Oil Pump Drive Shaft Ball
Spring 
Screw Plug
Valve Seat

Dust Deflector
 Oil Seal Seal Ring
Rear Output Shaft
 Non− reusable Part
 Precoated part Separator
Driven Rotor
−
TRANSFER REAR EXTENSION HOUSING
TR−29
839
Author: Date:
1996 LAND CRUISER (RM451U)
REAR EXTENSION HOUSING
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BI−01
Q00530
Q08384
Q02549
Q07138
TR−30
−
TRANSFER REAR EXTENSION HOUSING
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE OIL PUMP DRIVE SHAFT
2. REMOVE OIL PUMP COVER
(a) Using a torx socket wrench (T30), remove the 3 screws.
(b) Install the 2 suitable bolts to the pump cover.
(c) Remove the pump cover from the rear extension housing.
3. REMOVE DRIVE ROTOR FROM DRIVEN ROTOR
4. REMOVE DRIVEN ROTOR FROM REAR EXTENSION HOUSING
5. REMOVE SCREW PLUG, SPRING, BALL AND VALVE SEAT
(a) Using a hexagon wrench, remove the screw plug.
(b) Using a magnetic finger, remove the spring, ball and valve
seat from the rear extension housing.
6. REMOVE CENTER DIFFERENTIAL CONTROL COU- PLING ASSEMBLY
(a) Using a snap ring expander, remove the snap ring.
(b) Remove the coupling assembly from the rear extension housing.
7. REMOVE SEPARATOR AND OIL PUMP PLATE
Remove the 3 bolts, separator and oil pump plate.
8. REMOVE VEHICLE SPEED SENSOR DRIVE GEAR
(a) Using a snap ring expander, remove the snap ring.
(b) Remove the vehicle speed sensor drive gear.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TF0969
SST
TF0958
Q07138
Q02549
Q08384
TR−34
−
TRANSFER REAR EXTENSION HOUSING
1996 LAND CRUISER (RM451U)
4. INSTALL REAR OUTPUT SHAFT
(a) Using SST and a press, install the rear output shaft.
SST 09316−20011, 09316 −60011 (09316−00011,
09316 −00031)
(b) Install the 2 seal rings to the rear output shaft.
(c) Select a snap ring that will allow minimum axial play.
MarkThickness mm (in.)
11.95 (0.0768)
22.05 (0.0807)
32.15 (0.0847)
42.25 (0.0886)
(d) Using a snap ring expander, install a new snap ring.
5. INSTALL VEHICLE SPEED SENSOR DRIVE GEAR
(a) Install the vehicle speed sensor drive gear.
(b) Using a snap ring expander, install the snap ring.
6. INSTALL OIL PUMP PLATE AND SEPARATOR
(a) Install the oil pump plate.
(b) Install the separator.
(c) Install and torque the 3 bolts. Torque: 4.9 N·m (50 kgf·cm, 43 in.·lbf)
7. INSTALL CENTER DIFFERENTIAL CONTROL COU- PLING ASSEMBLY
(a) Install the coupling assembly to the output shaft.
(b) Using a snap ring expander, install the snap ring.
8. INSTALL VALVE SEAT, BALL, SPRING AND SCREW PLUG
(a) Apply gear oil to the ball.
(b) Install the valve seat, ball and spring.
(c) Apply liquid sealer to the screw plug.
Sealant: Part No. 08833−00080, THREE BOND 1344,
LOCTITE 242 or equivalent
(d) Using a hexagon wrench, install and torque the screw plug.
Torque: 29 N·m (300 kgf·cm, 22 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR0BL−01
TR−36
−
TRANSFER MOTOR SHIFT CONTROL SYSTEM
846
Author: Date:
1996 LAND CRUISER (RM451U)
MOTOR SHIFT CONTROL SYSTEM
LOCATION
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q02622
Light upGoes off
L
NH
DIFF LOCK
DIFF LOCK
TR0BM−03
Z15367
Relay Side
V01699
V06651
−
TRANSFER MOTOR SHIFT CONTROL SYSTEM
TR−37
1996 LAND CRUISER (RM451U)
INSPECTION
1. INSPECT SHIFT LEVER POSITION
(a) Start the engine, and turn the center diff lock switch to
OFF.
(b) Check that the center diff indicator light comes on when the transfer shift lever shifted to the ”L” position. Check
that the light goes off when the lever is shifted to the ”N”
or ”H” position.
2. INSPECT CENTER DIFF LOCK CONTROL RELAY
(a) Check that there is continuity between the terminals, as shown in the chart.
HINT:
There is a diode between the terminals 6 and 7. If the circuit
shown no continuity, change the positive (+) and negative ( −)
probes and recheck the circuit.
(b) Apply battery positive voltage between the terminals and check that there is continuity between the terminals, as
shown in the chart.
If continuity is not as specified, replace the relay.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

TR−38
−
TRANSFER MOTOR SHIFT CONTROL SYSTEM
1996 LAND CRUISER (RM451U)
3. INSPECT MOTOR ACTUATOR
(a) Measure the resistance between the terminals 2 and 3.
Standard resistance: 0.3 − 100 Ω
(b) Measure the resistance between the terminals 2 or 3 and
body ground.
Standard resistance: More than 0.5 MΩ
If the resistance value is not as specified, replace the motor ac-
tuator.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010