distributor TOYOTA LAND CRUISER 1996 J80 Owner's Manual

IG0IC−01
−
IGNITION DISTRIBUTOR
IG−9
743
Author: Date:
1996 LAND CRUISER (RM451U)
DISTRIBUTOR
COMPONENTS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG0ID−01
IG−10
−
IGNITION DISTRIBUTOR
1996 LAND CRUISER (RM451U)
REMOVAL
1. DISCONNECT DISTRIBUTOR CONNECTOR
2. REMOVE DISTRIBUTOR CAP WITHOUT DISCON- NECTING HIGH−TENSION CORDS
3. SET NO.1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley until the timing mark is aligned with ”0” mark on the timing chain cover.
(b) Check that the distributor rotor direction is as shown.
If not, turn the crankshaft pulley one complete revolution.
4. REMOVE DISTRIBUTOR
(a) Remove the hold −down bolt and pull out the distributor.
(b) Remove the O−ring from the distributor housing.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG0IE−01
−
IGNITION DISTRIBUTOR
IG−11
1996 LAND CRUISER (RM451U)
INSTALLATION
1. CHECK NO.1 CYLINDER TO TDC/COMPRESSION
If necessary, remove the cylinder head cover, and check these
conditions:
Turn the crankshaft pulley and align its groove with
the timing mark ”0” of the timing chain cover.
Verify that the timing marks with 1 and 2 dots are in
straight line on the cylinder head surface as shown
in the illustration.
If not, turn the crankshaft 1 revolution (360°) and align the mark
as above.
2. INSTALL DISTRIBUTOR
(a) Install a new O−ring to the distributor.
HINT:
Always use a new O −ring when installing the distributor.
(b) Align the groove of the distributor housing with the protru-
sion on the driven gear.
(c) Apply a light coat of engine oil on the O −ring.
(d) Insert the distributor, aligning the center of the flange with
that of the bolt hole on the cylinder head.
(e) Lightly tighten the hold −down bolt.
3. INSTALL DISTRIBUTOR CAP
4. CONNECT DISTRIBUTOR CONNECTOR
5. CHECK IGNITION TIMING (See page EM−10)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EP−01
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
SS−7
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Distributor x Cylinder head1818013
No. 1 engine hanger x Cylinder head4142030
No. 2 engine hanger x Cylinder head4142030
Air intake chamber x Intake manifold2121015
Intake manifold x Cylinder head2121015
Heater inlet pipe x Intake manifold2121015
EGR pipe x Cylinder head2121015
EGR pipe x EGR valve Union nut7880058
Water outlet x Cylinder head2121015
Generator bracket x Cylinder head4344032
Cylinder head x Cylinder block 1st
2nd 3rd39
Turn 90°
Turn 90°400
Turn 90°
Turn 90°29
Turn 90°
Turn 90°
Cylinder head x Timing chain cover2121015
Camshaft bearing cap x Cylinder head1616012
Camshaft timing gear x Camshaft7475054
Chain tensioner x Cylinder head2121015
Water bypass outlet x Cylinder head2121015
Heater pipe x Timing chain cover2121015
Heater pipe x Cylinder head2020014
Exhaust manifold x Cylinder head3940029
Heat insulator x Exhaust manifold1919514
Front exhaust pipe x Exhaust manifold6363046
No. 1 support bracket x Transmission2424017
No. 1 support bracket clamp bolt19.519514
Front exhaust pipe x Rear TWC4647034
No. 2 water bypass pipe x Cylinder head2020014
No. 2 water bypass pipe x No. 1 engine hanger2020014
Fuel inlet hose x Fuel filter2930022
Intake manifold stay x Air intake chamber3636026
Intake manifold stay x Cylinder block3636026
Oil dipstick guide x Intake manifold2020014
Oil dipstick guide x No. 1 oil pan2020014
PS reservoir tank x Air intake chamber2020014
Oil jet x Cylinder block2020014
Vibration damper x Cylinder block2020014
Chain tensioner slipper x Cylinder block6970051
Timing chain cover x Cylinder block2121015
Drive belt idler pulley x Timing chain cover4344032
Crankshaft pulley x Crankshaft4124,200304
Transmission housing x No. 1 oil pan7273053
Oil level sensor x No. 1 oil pan5.45548 in.·lbf
Water pump x Cylinder block2121015
Radiator pipe x No. 1 oil pan2121015
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EY−03
−
SERVICE SPECIFICATIONS IGNITION
SS−17
140
Author: Date:
1996 LAND CRUISER (RM451U)
IGNITION
SERVICE DATA
Firing order−1 − 5 − 3 − 6 − 2 − 4
High −tension cordResistance Maximum25 kΩ per cord
Spark plugRecommended spark plug ND
NGK
Correct electrode gapK16R−U
BKR5EYA
0.8 mm (0.031 in.)
Ignition coilPrimary coil resistance at cold
at hot
Secondary coil resistance at cold
at hot0.36 − 0.55 Ω
0.45 − 0.65 Ω
9.0 − 15.4 kΩ
11.4 − 18.1 kΩ
DistributorAir gap
Pickup coil resistance at cold (G1 − G)
(G2 − G)
(NE − G)
at hot (G1 − G )
(G2 − G)
(NE − G)0.2 − 0.4 mm (0.008 − 0.016 in.)
185 − 275 Ω
185 − 275 Ω
185 − 275 Ω
240 − 325 Ω
240 − 325 Ω
240 − 325 Ω
Crankshaft
position sensorResistance at cold (NE − NE )
at hot (NE − NE )1,630 − 2,740 Ω
2,065 − 3,225 Ω
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EZ−01
SS−18
−
SERVICE SPECIFICATIONS IGNITION
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Spark plug x Cylinder head2020014
Distributor x Cylinder head1818013
Crankshaft position sensor protector x No. 1 oil pan2020014
Crankshaft position sensor x No. 1 oil pan99078 in.·lbf
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010