ECU TOYOTA LAND CRUISER 1996 J80 Owner's Guide

−
DIAGNOSTICS ENGINE
DI−7
1996 LAND CRUISER (RM451U)
(10) After checking the DTC, inspect the applicable cir-
cuit.
(b) Clear the DTC.
The following actions will erase the DTCs and freezed
frame data.
(1) Operating the OBD II scan tool (complying with SAE
J1978) or TOYOTA hand−held tester to erase the
codes. (See the OBD II scan tool’ s instruction book
for operating instructions.)
(2) Disconnecting the battery terminals or EFI fuse.
NOTICE:
If the TOYOTA hand −held tester switches the ECM from
normal mode to check mode or vice −versa, or if the igni-
tion switch is turned from ON to ACC or LOCK during check
mode, the DTCs and freezed frame data will be erased.
4. FAIL−SAFE CHART
If any of the following codes is recorded, the ECM enters fail −safe mode.
DTC No.Fail−Safe OperationFail− Safe Deactivation Conditions
P0100Ignition timing fixed at 5 ° BTDC
 Injection method fixed at simultaneous injectionReturned to normal condition
P0110Intake air temp. is fixed at 20° C (68°F)Returned to normal condition
P0115Engine coolant temp. is fixed at 80 °(176°F)Returned to normal condition
P0120VTA is fixed at 0°
The following condition must be repeated at least 2 times
consecutively
When closed throttle position switch is ON:
0.1 V  VTA  0.95 V
P0135
P0141The heater circuit in witch an abnormality is detected is
turned offIgnition switch OFF
P0325
P0330Max. timing retardationIgnition switch OFF
P1300Fuel cutIGF signal is detected for 6 consective ignitions
P1605Max. timing retardationReturned to normal condition
5. CHECK FOR INTERMITTENT PROBLEMS
TOYOTA hand−held tester only:
By putting the vehicle’s ECM in check mode, 1 trip detection logic is possible instead of 2 trip detection logic
and sensitivity to detect open circuits is increased. This makes it easier \
to detect intermittent problems.
(1) Clear the DTC (See step 2).
(2) Set the check mode (See step 3).
(3) Perform a simulation test (See page IN−18).
(4) Check the connector and terminal (See page IN−28).
(5) Handle the connector (See page IN−28).
(6) Visual check and contact pressure (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22487
No.1 Vehicle
Speed SensorCombination
Meter ECM
4−pulse
4−pulse
P22473
Combination Meter
3
C13 L−WL
−W8
E7 SPD ECM
5V
E1
From Cruise Control ECU
−
DIAGNOSTICS ENGINE
DI−87
1996 LAND CRUISER (RM451U)
DTC P0500 Vehicle Speed Sensor Malfunction
CIRCUIT DESCRIPTION
The vehicle speed sensor outputs a 4 − pulse signal for every revolution of the rotor shaft, which is rotated
by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectan-
gular wavefrom by the waveform shaping circuit inside the combination meter, it is then transmitted to the
ECM. The ECM determines the vehicle speed based on the frequency of thes\
e pulse signals.
DTC No.DTC Detecting ConditionTrouble Area
P0500
No vehicle speed sensor signal to ECM under conditions (a)
and (b):
(2 trip detection logic)
(a) Park/neutral position switch is OFF.
(b) Vehicle is being driven. Open or short in No.1 vehicle speed sensor circuit
 No.1 vehicle speed sensor
 Combination meter
 ECM
WIRING DIAGRAM
DI5PN−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

A00176
ONSPD
(+)
(−)
BE6653
P24668
AT7809
9 − 14 V
0
Turn the wheel
DI−88
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Check operation of speedometer.
CHECK:
Drive the vehicle and check if the operation of the speedmeter in the co\
mbination meter is normal.
HINT:
The vehicle speed sensor is operating normally if the speedometer displa\
y is normal.
NG Check speedometer circuit (See page BE−2 ).
OK
2 Check voltage between terminal SPD of ECM connector and body ground.
PREPARATION:
(a) Remove instrument panel speaker No.1 panel (See page SF−65 ).
(b) Disconnect cruise control ECU connector.
(c) Shift the shift lever to neutral.
(d) Jack up a rear wheels on one side.
(e) Turn ignition switch ON.
CHECK:
Measure voltage between terminal SPD of ECM connector and
body ground when the wheel is turned slowly.
OK:
Voltage is generated intermittently.
NG Check and repair harness and connector between combination meter and ECM.
OK
Check and replace ECM (See page IN−28 ).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22475
BatteryFusible
Link
FL AM2
F7W−R
EA2
W−R
B−R B−R
EA2
B−R
B−W B−W
W−B
Distributor
Ignition
Coil 4
12
EA2
IH1
W−B
8 1
2
Noise
Filter 45
B 3
Igniter Tr2
2
1
IH2 IH2
B−G
B−G
B−Y B−YE4
E4 IGT
IGF Tr15V
ECM
1 3 11
6
IG Switch
1
EC
17 23
14 13
−
DIAGNOSTICS ENGINE
DI−97
1996 LAND CRUISER (RM451U)
DTC P1300 Igniter Circuit Malfunction
CIRCUIT DESCRIPTION
The ECM determines the ignition timing, turns on Tr1 at a predetermined angle ( °CA) before the desired
ignition timing and outputs and ignition signal (IGT) ”1” to the\
igniter.
Since the width of the IGT signal is constant, the dwell angle control circuit in \
the igniter determines the time
the control circuit starts primary current flow to the ignition coil based \
on the engine rpm and ignition timing
one revolution ago, that is, the time the Tr2 turns on.
When it reaches the ignition timing, the ECM turns Tr1 off and outputs the IGT signal ”O”.
This turns Tr2 off, interrupting the primary current flow and generating a high voltage i\
n the secondary coil
which causes the spark plug to spark. Also, by the counter electromotive forc\
e generated when the primary
current is interrupted, the igniter sends an ignition confirmation signal (IGF)\
to the ECM. The ECM stops fuel
injection as a fail safe function when the IGF signal is not input to the ECM.
DTC No.DTC Detecting ConditionTrouble Area
P1300No IGF signal to ECM for 6 consecutive IGT signals during
engine running Open or short in IGF or IGT circuit from igniter to ECM
 Igniter
 ECM
WIRING DIAGRAM
DI5PQ−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT3417
OK if hot
Add if hot
Q07273
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−137
1996 LAND CRUISER (RM451U)
(e) P position test.
Stop the vehicle on a grade (more than 5 °) and after shifting into the P position, release the parking
brake. Then, check to see that the parking lock pawl holds the vehicle i\
n place.
6. BASIC INSPECTION
(a) Check the fluid level.
HINT:
Drive the vehicle so that the engine and transmission are
at normal operating temperature.
Fluid temp.: 70 − 80°C (158 − 176° F)
Only use the COOL range on the dipstick as a rough refer-
ence when the ATF is replaced or the engine does not
run.
(1) Park the vehicle on a level surface and set the park-
ing brake.
(2) With the engine idling and the brake pedal de- pressed, shift the shift lever into all positions from P
to L position and return to P position.
(3) Pull out the dipstick and wipe it clean.
(4) Push it back fully into the pipe.
(5) Pull it out and check that the fluid level is in the HOT range.
If the level is at the low side, add new fluid. Fluid type: ATF DEXRON ®II
NOTICE:
Do not overfill.
(b) Check the fluid condition. If the fluid smells burnt or is black, replace it.
(c) Replace the ATF. (1) Remove the drain plug and drain the ATF.
(2) Reinstall the drain plug securely.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07463
TransmissionFrom Cruise
Control ECU
W
R−YECM
1
2 B+
S1
B E4
R
S2
Shift Solenoid
Valve No. 2
B+
E4
EC2
EC2
Shift Solenoid
Valve No. 1
10
9
R
R−Y R−Y
1
2
Q07641
S2
S1
DI−158
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Measure resistance between terminal S1 or S2 of ECM and body ground.
PREPARATION:
Disconnect the connector from the ECM.
CHECK:
Measure the resistance between terminal S1 or S2 of the ECM
and body ground.
OK:
Resistance: 11 − 15 Ω
OK Check and replace ECM.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07467
Cruise Control ECUOD OD1B+
G−O
9 18ECM
E7
BE3840
Q07658 D00091
ON
(−) (+) OD1
DI−172
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
O/D Cancel Signal Circuit
CIRCUIT DESCRIPTION
While driving with cruise control activated, in order to minimize gear shifting and provide\
smooth cruising on
an uphill, overdrive may be prohibited temporarily in some conditions.
The cruise control ECU sends O/D cut signals to the ECM as necessary and\
the ECM cancels overdrive
shifting until these signals are discontinued.
(For details, see the Cruise Control section, page DI−292)
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check voltage between terminal OD1 of ECM and body ground.
PREPARATION:
Turn the ignition switch ON.
CHECK:
Measure the voltage between terminal OD1 of the ECM and
body ground.
OK:
Voltage: 9 − 14 V
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−147 ).
NG
DI5L0−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

BE3840
Q07660 D00015
ON
OD
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−173
1996 LAND CRUISER (RM451U)
2 Check voltage between terminal OD of cruise control ECU harness side connec-
tor and body ground.
PREPARATION:
(a) Disconnect the cruise control ECU connector.
(b) Turn ignition switch ON.
CHECK:
Measure the voltage between terminal OD of the cruise control
ECU harness side connector and body ground.
OK:
Voltage: 9 − 14 V
OK Check and replace cruise control ECU.
NG
3 Check harness and connector between cruise control ECU and ECM (See pag\
e IN−28 ).
NG Repair or replace wire harness or connector.
OK
Check and replace ECM.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

R01346
Normal Code
0.25 sec.
0.25 sec.
2 sec.
ON
OFF
ON
OFF 0.5 sec. 0.5 sec.
Code 11 and 21
4 sec.
1.5 sec.
2.5 sec.
Code 11 Code 21
BR1804
F00006DLC1 Short Pin
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
DI−191
1996 LAND CRUISER (RM451U)
As an example, the blinking patterns for normal code and
codes 11 and 21 are shown in the illustration.
(6) Code are explained in the code table on page
DI−196 .
(7) After completing the check, disconnect terminals Tc
and E
1, and turn off the display.
If 2 or more malfunctions are indicated at the same time the low-
est numbered DTC will be displayed 1st.
(c) Clear the DTC.
(1) Confirm that the center differential is free.
(2) Using SST, connect terminals Tc and E
1 of the
DLC1 and remove the short pin from the DLC1.
SST 09843−18020
(3) Turn the ignition switch ON.
(4) Clear the DTC stored in ECU by depressing the
brake pedal 8 or more times within 3 seconds.
(5) Check that the warning light shows the normal
code.
(6) Remove the SST from the terminals of the DLC1.
SST 09843−18020
(7) Connect the short pin to the DLC1.
HINT:
Cancellation can also be done by removing the ECU −B fuse,
but in this case, other memory systems will also be cancelled
out.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

N09348
Interface BoxHarness VehicleTOYOTA
Tester
Hand
−held
TOYOTA Break −out− box
F00007
DLC1
Ts Tc
E
1
BR3904
0.25 sec. 0.25 sec.
ON
OFF
DI−192
−
DIAGNOSTICS ANTI−LOCK BRAKE SYSTEM
1996 LAND CRUISER (RM451U)
(d) Using TOYOTA break −out− box and TOYOTA hand− held
tester, measure the ECU terminal values.
(1) Hook up the T OYOTA hand−held tester and TOYO-
TA break−out−box to the vehicle.
(2) Read the ECU input/output values by following the prompts on the tester screen.
HINT:
TOYOTA hand −held tester has a ”Snapshot ” function. This re-
cords the measured values and is effective in the diagnosis of
intermittent problems.
Please refer to the TOYOTA hand−held tester/TOYOTA break
out−box operators manual for further details.
2. SPEED SENSOR SIGNAL AND DECELERATION SEN-
SOR CHECK
(a) Check the speed sensor signal. (1) Conform that the center differential is free.
(2) Turn the ignition switch OFF.
(3) Using SST, connect terminals Ts and E
1 of the
DLC1.
SST 09843−18020
(4) Start the engine.
(5) Check that the ABS warning light blinks.
HINT:
If the ABS warning light does not blink, inspect the ABS warning
light circuit (See page DI−230).
(6) Drive vehicle straight forward.
HINT:
Drive vehicle faster than 45 km/h (28 mph) for several seconds.
(7) Stop the vehicle.
(8) Using SST, connect terminals Tc and E
1 of the
DLC1.
SST 09843−18020
(9) Read the number of blinks of the ABS warning light.
HINT:
See the list of DTC on page DI−190 .
If every sensor is normal, a normal code is output (A cycle of
0.25 sec. ON and 0.25 sec. OFF is repeated).
If 2 or more malfunction are indicated at the same time, the low-
est numbered code will be displayed 1st.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010