oil level TOYOTA LAND CRUISER 1996 J80 Owner's Guide

SS1EP−01
−
SERVICE SPECIFICATIONS ENGINE MECHANICAL
SS−7
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Distributor x Cylinder head1818013
No. 1 engine hanger x Cylinder head4142030
No. 2 engine hanger x Cylinder head4142030
Air intake chamber x Intake manifold2121015
Intake manifold x Cylinder head2121015
Heater inlet pipe x Intake manifold2121015
EGR pipe x Cylinder head2121015
EGR pipe x EGR valve Union nut7880058
Water outlet x Cylinder head2121015
Generator bracket x Cylinder head4344032
Cylinder head x Cylinder block 1st
2nd 3rd39
Turn 90°
Turn 90°400
Turn 90°
Turn 90°29
Turn 90°
Turn 90°
Cylinder head x Timing chain cover2121015
Camshaft bearing cap x Cylinder head1616012
Camshaft timing gear x Camshaft7475054
Chain tensioner x Cylinder head2121015
Water bypass outlet x Cylinder head2121015
Heater pipe x Timing chain cover2121015
Heater pipe x Cylinder head2020014
Exhaust manifold x Cylinder head3940029
Heat insulator x Exhaust manifold1919514
Front exhaust pipe x Exhaust manifold6363046
No. 1 support bracket x Transmission2424017
No. 1 support bracket clamp bolt19.519514
Front exhaust pipe x Rear TWC4647034
No. 2 water bypass pipe x Cylinder head2020014
No. 2 water bypass pipe x No. 1 engine hanger2020014
Fuel inlet hose x Fuel filter2930022
Intake manifold stay x Air intake chamber3636026
Intake manifold stay x Cylinder block3636026
Oil dipstick guide x Intake manifold2020014
Oil dipstick guide x No. 1 oil pan2020014
PS reservoir tank x Air intake chamber2020014
Oil jet x Cylinder block2020014
Vibration damper x Cylinder block2020014
Chain tensioner slipper x Cylinder block6970051
Timing chain cover x Cylinder block2121015
Drive belt idler pulley x Timing chain cover4344032
Crankshaft pulley x Crankshaft4124,200304
Transmission housing x No. 1 oil pan7273053
Oil level sensor x No. 1 oil pan5.45548 in.·lbf
Water pump x Cylinder block2121015
Radiator pipe x No. 1 oil pan2121015
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EX−04
SS−16
−
SERVICE SPECIFICATIONS LUBRICATION
1996 LAND CRUISER (RM451U)
TORQUE SPECIFICATION
Part tightenedN·mkgf·cmft·lbf
Oil pan x Drain plug2525018
Oil pump x Relief valve plug4950036
Drive belt idler pulley x Oil pump4344032
Oil strainer x No. 1 oil pan2020014
Baffle plate x No. 1 oil pan9.09078 in.·lbf
No. 1 oil pan x Cylinder block 14 mm head bolt
12 mm head bolt44
20440
20032
14
No. 1 oil pan x Oil pump (Timing chain cover)2020014
No. 2 oil pan x No. 1 oil pan Bolt
Nut7.8
8.880
9069 in.·lbf
78 in.·lbf
No. 1 oil pan x Transmission housing7273053
Oil level sensor x No. 1 oil pan5.45548 in.·lbf
Water pump x Cylinder block2121015
Radiator pipe x No. 1 oil pan2121015
A/C compressor bracket x No. 1 oil pan3737527
A/C compressor bracket x Cylinder block3737527
A/C compressor x A/C compressor bracket2525018
Oil cooler cover x Relief valve plug3737527
Oil cooler x Oil cooler cover1717012
Oil cooler cover x Cylinder block2121015
No. 1 exhaust manifold x Cylinder head3940029
No. 1 exhaust manifold x Heat insulator1919514
Front exhaust pipe x Exhaust manifold6363046
No. 1 support bracket x Transmission housing2424017
Front exhaust pipe x No. 1 support bracket Clamp bolt19.519514
Front exhaust pipe x Rear TWC4647034
Oil check valve x Cylinder block2525018
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SS1EG−02
−
SERVICE SPECIFICATIONS STEERING
SS−37
160
Author: Date:
1996 LAND CRUISER (RM451U)
STEERING
SERVICE DATA
ON−VEHICLE INSPECTION
Steering wheel freeplay Maximum40 mm (1.57 in.)
Fluid level riseMaximumBelow 5 mm (020 in.)
Fluid pressure at idle speed with valve closed Minimum9,316 kPa (95 kgf/cm2, 1,351 psi)
Steering effort at idle speedMaximum8.3 N·m (85 kgf·cm, 73 in.·lbf)
TILT STEERING COLUMN
Pawl stopper alignment mark 1 or A
2 or B
3 or C
4 or D 5 or E12.65 − 12.75 mm (0.4980 − 0.5020 in.)
12.55 − 12.65 mm (0.4941 − 0.4980 in.)
12.45 − 12.55 mm (0.4902 − 0.4941 in.)
12.35 − 12.45 mm (0.4962 − 0.4902 in.)
12.25 − 12.35 mm (0.4823 − 0.4862 in.)
PS VANE PUMP
Oil clearance between pump shaft and bushing STD
Maximum0.03 − 0.05 mm (0.0012 − 0.0020 in.)
0.07 mm (0.0028 in.)
Vane plate height Minimum8.6 mm (0.339 in.)
Vane plate thickness Minimum1.397 mm (0.05500 in.)
Vane plate length Minimum14.991 mm (0.59016 in.)
Vane plate and pump rotor groove clearanceMaximum0.033 mm (0.00130 in.)
Vane plate lengthPump rotor mark
None1
2
Cam ring mark
2
3
4
14.995 − 14.997 mm (0.59035 − 0.59043 in.)
14.993 − 14.995 mm (0.59027 − 0.59035 in.)
14.991 − 14.993 mm (0.59020 − 0.59027 in.)
14.995 − 14.997 mm (0.59035 − 0.59043 in.)
14.993 − 14.995 mm (0.59027 − 0.59035 in.)
14.991 − 14.993 mm (0.59020 − 0.59027 in.)
Spring free length STD35 − 37 mm (1.38 − 1.46 in.)
Vane pump rotaing torque Maximum0.3 N·m (2.8 kgf·cm, 2.4 in.·lbf)
PS GEAR
Worm gear valve body ball clearanceMaximum0.15 mm (0.059 in.)
Cross shaft adjusting screw thrust clearance STD0.03 − 0.05 mm (0.0012 − 0.0020 in.)
Worm gear preload0.3 − 0.5 N·m (3 − 5.5 kgf·cm, 2.6 − 4.8 in.·lbf)
Total preload0.74 − 1.08 N·m (7.5 − 11.0 kgf·cm, 6.5 − 9.6 in.·lbf)
STEERING LINKAGE
Tie rod length Approximately1.207 mm (47.51 in.)
Relay rod lengthApproximately1.085 mm (42.72 in.)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010