Timing TOYOTA LAND CRUISER 1996 J80 Service Manual

−
ENGINE MECHANICAL ENGINE UNIT
EM−81
1996 LAND CRUISER (RM451U)
26. CONNECT EVAP HOSE
27. CONNECT BRAKE BOOSTER VACUUM HOSE
28. CONNECT HEATER VALVE AND ENGINE WIRE TO
COWL PANEL
(a) Connect the heater valve with the 2 bolts.
(b) Connect the engine wire and ground strap with the 2 bolts.
29. CONNECT HEATER HOSES
30. CONNECT ACCELERATOR CABLE TO THROTTLE BODY
31. CONNECT CRUISE CONTROL ACTUATOR CABLE TO
THROTTLE BODY
32. INSTALL AIR CLEANER CASE
33. INSTALL AIR CLEANER HOSE AND CAP
34. CONNECT OIL COOLER HOSE TO OIL COOLER PIPE
35. INSTALL RADIATOR (See page CO−16)
36. INSTALL RADIATOR GRILLE
Install the radiator grille with the 5 screws and clip.
37. INSTALL BATTERY TRAY AND BATTERY
(a) Install the battery tray with the 5 bolts.
(b) Connect the ground strap with the bolt.
(c) Install the battery and hold−down clamp with the nuts.
(d) Connect the battery cables.
38. FILL WITH ENGINE OIL
39. FILL RADIATOR WITH ENGINE COOLANT
40. START ENGINE AND CHECK FOR LEAKS
41. CHECK AUTOMATIC TRANSMISSION FLUID LEVEL
42. CHECK IGNITION TIMING (See page EM−10)
43. INSTALL HOOD
44. PERFORM ROAD TEST
Check for abnormal noise, shock, slippage, correct shift points
and smooth operation.
45. RECHECK ENGINE COOLANT AND ENGINE OIL LEV-
ELS
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

EM1Q8−01
−
ENGINE MECHANICAL CYLINDER BLOCK
EM−83
1996 LAND CRUISER (RM451U)
DISASSEMBLY
1. REMOVE DRIVE PLATE
Uniformly loosen and remove the drive plate bolts, in several
passes, in the sequence shown.
2. INSTALL ENGINE TO ENGINE STAND FOR DIS-
ASSEMBLY
3. REMOVE CYLINDER HEAD (See page EM−28 )
4. REMOVE TIMING CHAIN AND GEARS (See page EM−13 )
5. REMOVE OIL FILTER (See page LU−2)
6. REMOVE OIL FILTER UNION
7. REMOVE KNOCK SENSORS
Using SST, remove the 2 knock sensors. SST 09816−30010
8. REMOVE PS PUMP
(a) Remove the 2 nuts and pump.
(b) Remove the O−ring from the pump.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P04907
P08469
SST
EM−100
−
ENGINE MECHANICAL CYLINDER BLOCK
1996 LAND CRUISER (RM451U)
2. REPLACE OVERSIZED (O/S) PISTONS FOR CYLIN-
DER BORING
HINT:
Bore all the 6 cylinders for the O/S piston outside diame-
ter.
Replace all the piston rings with ones to match the O/S
pistons.
(a) Keep 6 new O/S pistons. O/S piston diameter:
O/S 0.50100.450 − 100.480 mm (3.9547 − 3.9559 in.)
O/S 1.00100.950 − 100.980 mm (3.9744 − 3.9756 in.)
(b) Using a micrometer, measure the piston diameter at right
angles to the piston pin center line, 42 mm (1.65 in.) from
the piston head.
(c) Calculate the amount of each cylinder is to be rebored as
follows:
Size to be rebored = P + C − H
P = Piston diameter
C = Piston oil clearance
0.040 − 0.060 mm (0.0016 − 0.0024 in.)
H = Allowance for honing
0.02 mm (0.0008 in.) or less
(d) Bore and hone the cylinders to calculated dimensions. Maximum honing: 0.02 mm (0.0008 in.)
NOTICE:
Excess honing will destroy the finished roundness.
3. REPLACE CRANKSHAFT FRONT OIL SEAL
HINT:
There are 2 methods ((a) and (b)) to replace the oil seal.
(a) If the timing chain cover is removed from the cylinder block:
(1) Using a screwdriver and a hammer, tap out the oilseal.
(2) Using SST and a hammer, tap in a new oil seal until
its surface is flush with the timing chain cover edge.
SST 09316−60011 (09316 −00011, 09316−00051)
(3) Apply MP grease to the oil seal lip.
NOTICE:
Do not let foreign matter get onto the lip of the oil seal.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P05005
P08506
SST
P04518
P04970
SST
P08643
Cut Position
−
ENGINE MECHANICAL CYLINDER BLOCK
EM−101
1996 LAND CRUISER (RM451U)
(b) If the timing chain cover is installed to the cylinder block:
(1) Using a screwdriver, pry out the oil seal.
NOTICE:
Be careful not to damage the crankshaft. Tape the screw-
driver tip.
(2) Apply MP grease to a new oil seal lip.
NOTICE:
Do not let foreign matter get onto the lip of the oil seal.
(3) Using SST and a hammer, tap in the oil seal until its
surface is flush with the timing chain cover edge.
SST 09316−60011 (09316 −00011, 09316−00051)
4. REPLACE CRANKSHAFT REAR OIL SEAL
HINT:
There are 2 methods ((a) and (b)) to replace the oil seal.
(a) If the rear oil seal retainer is removed from the cylinder block:
(1) Using a screwdriver and a hammer, tap out the oil
seal.
(2) Using SST and a hammer, tap in a new oil seal until
its surface is flush with the rear oil seal edge.
SST 09223−15030, 09950 −70010 (09951−07150)
NOTICE:
Do not let foreign matter get onto the lip of the oil seal.
(b) If the rear oil seal retainer is installed to the cylinder block:
(1) Using a knife, cut off the oil seal lip.
(2) Using a screwdriver, pry out the oil seal.
NOTICE:
Be careful not to damage the crankshaft. Tape the screw-
driver tip.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
ENGINE MECHANICAL CYLINDER BLOCK
EM−109
1996 LAND CRUISER (RM451U)
14. INSTALL LH ENGINE MOUNTING BRACKET
(a) Install the bracket with the 4 bolts.
Torque: 69 N·m (700 kgf·cm, 51 ft·lbf)
(b) Install the insulator with the nut. Torque: 72 N·m (730 kgf·cm, 43 ft·lbf)
15. INSTALL RH ENGINE MOUNTING BRACKET
(a) Install the bracket with the 4 bolts. Torque: 69 N·m (700 kgf·cm, 51 ft·lbf)
(b) Install the insulator with the nut. Torque: 72 N·m (730 kgf·cm, 43 ft·lbf)
16. INSTALL PS PUMP
(a) Place a new O−ring to the pump.
(b) Install the pump with the 2 nuts.
Torque: 36 N·m (370 kgf·cm, 27 ft·lbf)
17. INSTALL KNOCK SENSORS
Using SST, install the 2 knock sensors. SST 09816−30010
Torque: 44 N·m (450 kgf·cm, 33 ft·lbf)
18. INSTALL OIL FILTER UNION
Torque: 44 N·m (450 kgf·cm, 33 ft·lbf)
19. INSTALL OIL FILTER (See page LU−2)
20. INSTALL TIMING CHAIN (See page EM−19)
21. INSTALL CYLINDER HEAD (See page EM−54 )
22. REMOVE ENGINE STAND
23. INSTALL DRIVE PLATE
(a) Install the front spacer, drive plate and rear plate on the crankshaft.
(b) Install and uniformly tighten the 10 drive plate bolts, in several passes, in the sequence shown.
Torque: 100 N·m (1,000 kgf·cm, 74 ft·lbf)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG0ID−01
IG−10
−
IGNITION DISTRIBUTOR
1996 LAND CRUISER (RM451U)
REMOVAL
1. DISCONNECT DISTRIBUTOR CONNECTOR
2. REMOVE DISTRIBUTOR CAP WITHOUT DISCON- NECTING HIGH−TENSION CORDS
3. SET NO.1 CYLINDER TO TDC/COMPRESSION
(a) Turn the crankshaft pulley until the timing mark is aligned with ”0” mark on the timing chain cover.
(b) Check that the distributor rotor direction is as shown.
If not, turn the crankshaft pulley one complete revolution.
4. REMOVE DISTRIBUTOR
(a) Remove the hold −down bolt and pull out the distributor.
(b) Remove the O−ring from the distributor housing.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IG0IE−01
−
IGNITION DISTRIBUTOR
IG−11
1996 LAND CRUISER (RM451U)
INSTALLATION
1. CHECK NO.1 CYLINDER TO TDC/COMPRESSION
If necessary, remove the cylinder head cover, and check these
conditions:
Turn the crankshaft pulley and align its groove with
the timing mark ”0” of the timing chain cover.
Verify that the timing marks with 1 and 2 dots are in
straight line on the cylinder head surface as shown
in the illustration.
If not, turn the crankshaft 1 revolution (360°) and align the mark
as above.
2. INSTALL DISTRIBUTOR
(a) Install a new O−ring to the distributor.
HINT:
Always use a new O −ring when installing the distributor.
(b) Align the groove of the distributor housing with the protru-
sion on the driven gear.
(c) Apply a light coat of engine oil on the O −ring.
(d) Insert the distributor, aligning the center of the flange with
that of the bolt hole on the cylinder head.
(e) Lightly tighten the hold −down bolt.
3. INSTALL DISTRIBUTOR CAP
4. CONNECT DISTRIBUTOR CONNECTOR
5. CHECK IGNITION TIMING (See page EM−10)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22576
−
LUBRICATION OIL PUMP
LU−7
1996 LAND CRUISER (RM451U)
(b) Remove the No.1 oil pan by prying the portions (A) be-
tween the cylinder block and No.1 oil pan with a screw-
driver.
NOTICE:
Be careful not to damage the contact surfaces of the cylin-
der block and No.1 oil pan.
14. REMOVE OIL PAN BAFFLE PLATE
Remove the bolt, 7 nuts and baffle plate.
15. REMOVE OIL STRAINER
Remove the bolt, 2 nuts, oil strainer and gasket.
16. REMOVE CRANKSHAFT PULLEY (See page EM−13 )
17. REMOVE DRIVE BELT IDLER PULLEY
Remove the bolt and idler pulley.
18. REMOVE OIL PUMP (TIMING CHAIN COVER) (See page EM−13 )
19. REMOVE TIMING CHAIN AND CAMSHAFT TIMING GEAR
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

LU0KI−02
LU−12
−
LUBRICATION OIL PUMP
1996 LAND CRUISER (RM451U)
INSTALLATION
1. SET CRANKSHAFT
Turn the crankshaft until the set key on the crankshaft facing
downward.
2. INSTALL TIMING CHAIN AND CAMSHAFT TIMING GEAR (See page EM−19 )
3. INSTALL OIL PUMP (TIMING CHAIN COVER)(See
page EM−19 )
4. INSTALL DRIVE BELT IDLER PULLEY
Install the pulley with the bolt. Torque: 43 N·m (440 kgf·cm, 32 ft·lbf)
5. INSTALL CRANKSHAFT PULLEY (See page EM−19 )
6. INSTALL OIL STRAINER
Install a new gasket and the oil strainer with the bolt and 2 nuts. Torque: 20 N·m (200 kgf·cm, 14 ft·lbf)
7. INSTALL OIL PAN BAFFLE PLATE
Install the baffle plate with the bolt and 7 nuts.
Torque: 9.0 N·m (90 kgf·cm, 78 in.·lbf)
8. INSTALL NO.1 OIL PAN
(a) Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the oil pan,
oil pump and cylinder block.
Using a razor blade and gasket scraper, remove all
the old packing (FIPG) material from the gasket sur-
faces and sealing grooves.
Thoroughly clean all components to remove all the
loose material.
Using a non −residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the No.1 oil pan as shown in the il- lustration.
Seal packing: Part No. 08826−00080 or equivalent
Install a nozzle that has been cut to a 3 − 4 mm (0.12
− 0.16 in.) opening.
HINT:
Avoid applying an excessive amount to the surface.
Parts must be assembled within 5 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.
Immediately remove nozzle from the tube and rein-
stall cap.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

LU0KM−04
−
LUBRICATION OIL NOZZLE
LU−21
1996 LAND CRUISER (RM451U)
REMOVAL
1. REMOVE CYLINDER HEAD (See page EM−28 )
2. REMOVE TIMING CHAIN AND GEARS (See page EM−13 )
3. REMOVE CRANKSHAFT (See page EM−83 )
4. REMOVE OIL NOZZLES
Remove the 6 check valves and oil nozzles. Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
HINT:
At the time of installation, align the pin of the nozzle with the pin
hole of the cylinder block.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010