Throttle position TOYOTA LAND CRUISER 1996 J80 Workshop Manual

 DTC No.
Indicates the diagnostic trouble code.
 Page or Instructions
Indicates the page where the inspection procedure
for each circuit is to be found, or gives instructions
for checking and repairs. Detection Item
Indicates the system of the problem or
contents of the problem.  Trouble Area
Indicates the suspect area of the
problem.
Mass
Air Flow Circuit MalfunctionDetection Item
 Open or short in mass air flow meter circuit
 Mass air flow meter
 ECM
DTC No.
(See page)
Trouble Area
MIL* MemoryP0100
(DI−24)
P0101
(DI−28)
P0115
(DI−33)  Open or short in intake air temp. sensor
circuit
 Intake air temp. sensor
 ECM
Intake Air Temp. Circuit
Malfunction
P0110
(DI−29)
 Open or short in engine coolant temp. sensor circuit
 Engine coolant temp. sensor
 ECM
Throttle/ Pedal Position Sensor/Switch
”A” Circuit MalfunctionEngine Coolant Temp.
Circuit Malfunction
 Open or short in throttle position sensor circuit
 Throttle position sensor
 ECM
HINT:
Parameters listed in the chart may not be exactly the same as your readi\
ng due to the type of instrument or other
factors.
If a malfunction code is displayed during the DTC check mode, check the circ\
uit for the code listed in the table
below. For details of each code, turn to the page referred to under the ”See\
page” for the respective ”DTC No.”
in the DTC chart.
Mass Air Flow Circuit
Range/ Performance Problem Mass air flow meter
 Throttle position sensor
Throttle/
Pedal Position Sensor/ Switch
”A” Circuit Range / Performance Prob-
lem
P0116
(DI−37)
Engine Coolant Temp.
Circuit
Range/ Performance Problem Engine coolant temp. sensor
 Cooling system
SAE CONTROLLED
DIAGNOSTIC TROUBLE CODE CHART
IN−24−
INTRODUCTION HOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
1996 LAND CRUISER (RM451U)
4. DIAGNOSTIC TROUBLE CODE CHART
The inspection procedure is shown in the table below. This ta ble permits efficient and accurate troubleshoot-
ing using the diagnostic trouble codes displayed in the diagnostic trouble code check. Proceed with trouble-
shooting in accordance with the inspection procedure given in the diagnostic cha\
rt corresponding to the
diagnostic trouble codes displayed. The engine diagnostic trouble code chart is sho\
wn below as an example.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IN0CI−02
IN−38
−
INTRODUCTION TERMS
1996 LAND CRUISER (RM451U)
GLOSSARY OF SAE AND TOYOTA TERMS
This glossary lists all SAE− J1930 terms and abbreviations used in this manual in compliance with SAE\
rec-
ommendations, as well as their TOYOTA equivalents.
SAE
ABBREVIATIONSSAE TERMSTOYOT A TERMS
( ) −−ABBREVIA TIONS
A/CAir ConditioningAir Conditioner
ACLAir CleanerAir Cleaner, A/CL
AIRSecondary Air InjectionAir Injection (AI)
APAccelerator Pedal−
B+Battery Positive Voltage+B, Battery Voltage
BAROBarometric PressureHAC
CACCharge Air CoolerIntercooler
CARBCarburetorCarburetor
CFIContinuous Fuel Injection−
CKPCrankshaft PositionCrank Angle
CLClosed LoopClosed Loop
CMPCamshaft PositionCam Angle
CPPClutch Pedal Position−
CTOXContinuous T rap Oxidizer−
CTPClosed Throttle PositionLL ON, Idle ON
DFIDirect Fuel Injection (Diesel)Direct Injection (DI)
DIDistributor Ignition−
DLC1
DLC2
DLC3Data Link Connector 1
Data Link Connector 2
Data Link Connector 31: Check Connector
2: Total Diagnosis Comunication Link (TDCL)
3: OBD II Diagnostic Connector
DTCDiagnostic Trouble CodeDiagnostic Code
DTMDiagnostic Test Mode−
ECLEngine Control Level−
ECMEngine Control ModuleEngine ECU (Electronic Control Unit)
ECTEngine Coolant T emperatureCoolant Temperature, Water Temperature (THW)
EEPROMElectrically Erasable Programmable Read Only Memory
Electrically Erasable Programmable Read Only Memory
(EEPROM),
Erasable Programmable Read Only Memory (EPROM)
EFEEarly Fuel EvaporationCold Mixture Heater (CMH), Heat Control Valve (HCV)
EGRExhaust Gas RecirculationExhaust Gas Recirculation (EGR)
EIElectronic IgnitionTOYOTA Distributorless Ignition (TDI)
EMEngine ModificationEngine Modification (EM)
EPROMErasable Programmable Read Only MemoryProgrammable Read Only Memory (PROM)
EVAPEvaporative EmissionEvaporative Emission Control (EVAP)
FCFan Control−
FEEPROMFlash Electrically Erasable Programmable
Read Only Memory−
FEPROMFlash Erasable Programmable Read Only Memory−
FFFlexible Fuel−
FPFuel PumpFuel Pump
GENGeneratorAlternator
GNDGroundGround (GND)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
INTRODUCTION TERMS
IN−39
1996 LAND CRUISER (RM451U)
HO2S
Heated Oxygen SensorHeated Oxygen Sensor (HO2S)
IACIdle Air ControlIdle Speed Control (ISC)
IATIntake Air TemperatureIntake or Inlet Air T
emperature
ICMIgnition Control Module−
IFIIndirect Fuel InjectionIndirect Injection (IDL)
IFSInertia Fuel−Shutoff−
ISCIdle Speed Control−
KSKnock SensorKnock Sensor
MAFMass Air FlowAir Flow Meter
MAPManifold Absolute PressureManifold Pressure
Intake V acuum
MCMixture Control
Electric Bleed Air Control Valve (EBCV)
Mixture Control Valve (MCV)
Electric Air Control Valve (EACV)
MDPManifold Dif ferential Pressure−
MFIMultiport Fuel InjectionElectronic Fuel Injection (EFI)
MILMalfunction Indicator LampCheck Engine Lamp
MSTManifold Surface T emperature−
MVZManifold Vacuum Zone−
NVRAMNon−Volatile Random Access Memory−
O2SOxygen SensorOxygen Sensor, O2 Sensor (O2S)
OBDOn−Board DiagnosticOn− Board Diagnostic System (OBD)
OCOxidation Catalytic ConverterOxidation Catalyst Convert (OC), CCo
OPOpen LoopOpen Loop
PAIRPulsed Secondary Air InjectionAir Suction (AS)
PCMPowertrain Control Module−
PNPPark/Neutral Position−
PROMProgrammable Read Only Memory−
PSPPower Steering Pressure−
PTOXPeriodic Trap OxidizerDiesel Particulate Filter (DPF)
Diesel Particulate Trap (DPT)
RAMRandom Access MemoryRandom Access Memory (RAM)
RMRelay Module−
ROMRead Only MemoryRead Only Memory (ROM)
RPMEngine SpeedEngine Speed
SCSuperchargerSupercharger
SCBSupercharger BypassE−ABV
SFISequential Multiport Fuel InjectionElectronic Fuel Injection (EFI), Sequential Injection
SPLSmoke Puff Limiter−
SRIService Reminder Indicator−
SRTSystem Readiness Test−
STScan Tool−
TBThrottle BodyThrottle Body
TBIThrottle Body Fuel InjectionSingle Point Injection
Central Fuel Injection (Ci)
TCTurbochargerTurbocharger
TCCTorque Converter ClutchTorque Converter
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

IN−40
−
INTRODUCTION TERMS
1996 LAND CRUISER (RM451U)
TCM
Transmission Control ModuleTransmission ECU, ECT ECU
TPThrottle PositionThrottle Position
TRTransmission Range−
TVVThermal Vacuum V
alveBimetallic Vacuum Switching Valve (BVSV)
Thermostatic Vacuum Switching Valve (TVSV)
TWCThree−Way Catalytic Converter
Three−Way Catalytic (TWC)
Manifold Converter
CC
RO
TWC+OCThree−Way + Oxidation Catalytic ConverterCCR + CCo
VA FVolume Air FlowAir Flow Meter
VRVoltage RegulatorVoltage Regulator
VSSVehicle Speed SensorVehicle Speed Sensor
WOTWide Open ThrottleFull Throttle
WU−OCWarm Up Oxidation Catalytic Converter−
WU−TWCWarm Up Three−Way Catalytic Converter−
3GRThird Gear−
4GRFourth Gear−
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

AT0TD−01
−
AUTOMATIC TRANSMISSION AUTOMATIC TRANSMISSION UNIT
AT−25
1996 LAND CRUISER (RM451U)
INSTALLATION
1. CHECK TORQUE CONVERTER CLUTCH INSTALLA-
TION
Using calipers and a straight edge, measure from the installed
surface of the transmission housing. Correct distance: More than 15.7 mm (0.618 in.)
2. INSTALL TRANSMISSION
Installation is in the reverse order of removal (See page
AT −20 ).
HINT:
After installation, adjust the shift lever position and throttle
cable (See page DI−131).
Fill and check fluid level (See page DI−131).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

FI3605
ON
OFF Flashing
0.13 Second
DI−6
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
NOTICE:
When simulating symptoms with an OBD II scan tool (ex-
cluding TOYOTA hand −held tester) to check the DTC, use
normal mode. For codes on the DTC chart subject to ”2 trip
detection logic”, turn the ignition switch OFF after the
symptom is simulated the first time. Then repeat the simu-
lation process again. When the problem has been simu-
lated twice, the MIL lights up and the DTCs are recorded in
the ECM.
3. INSPECT DIAGNOSIS (CHECK MODE)
HINT:
TOYOTA hand−held tester only:
Compared to the normal mode, the check mode has an in-
creased sensitivity to detect malfunctions.
Furthermore, the same diagnostic items which are detected in
the normal mode can also be detected in the check mode.
(a) Check the DTC. (1) Initial conditions
Battery positive voltage 11 V or more.
Throttle valve fully closed.
Transmission in ”park” or ”neutral” position.
Air conditioning switched OFF.
(2) Turn ignition switch OFF.
(3) Prepare the TOYOTA hand−held tester.
(4) Connect the TOYOTA hand−held tester to DLC3 in
the fuse box at the lower left of the instrument panel.
(5) Turn the ignition switch ON and push the TOYOTA hand−held tester ON.
(6) Switch the TOYOTA hand −held tester normal mode
to check mode (Check that the MIL flashes.).
(7) Switch the engine (The MIL goes out after the en- gine start.).
(8) Simulate the conditions of the malfunction de- scribed by the customer.
NOTICE:
Leave the ignition switch ON until you have checked the
DTC, etc. (9) After simulating the malfunction conditions, use theTOYOTA hand−held tester diagnosis selector to
check the DTCs and freezed frame data, etc.
HINT:
Take care not to turn the ignition switch OFF. T urning the ignition
switch OFF switches the diagnosis system from check mode to
normal mode, so all DTCs, etc. are erased.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−7
1996 LAND CRUISER (RM451U)
(10) After checking the DTC, inspect the applicable cir-
cuit.
(b) Clear the DTC.
The following actions will erase the DTCs and freezed
frame data.
(1) Operating the OBD II scan tool (complying with SAE
J1978) or TOYOTA hand−held tester to erase the
codes. (See the OBD II scan tool’ s instruction book
for operating instructions.)
(2) Disconnecting the battery terminals or EFI fuse.
NOTICE:
If the TOYOTA hand −held tester switches the ECM from
normal mode to check mode or vice −versa, or if the igni-
tion switch is turned from ON to ACC or LOCK during check
mode, the DTCs and freezed frame data will be erased.
4. FAIL−SAFE CHART
If any of the following codes is recorded, the ECM enters fail −safe mode.
DTC No.Fail−Safe OperationFail− Safe Deactivation Conditions
P0100Ignition timing fixed at 5 ° BTDC
 Injection method fixed at simultaneous injectionReturned to normal condition
P0110Intake air temp. is fixed at 20° C (68°F)Returned to normal condition
P0115Engine coolant temp. is fixed at 80 °(176°F)Returned to normal condition
P0120VTA is fixed at 0°
The following condition must be repeated at least 2 times
consecutively
When closed throttle position switch is ON:
0.1 V  VTA  0.95 V
P0135
P0141The heater circuit in witch an abnormality is detected is
turned offIgnition switch OFF
P0325
P0330Max. timing retardationIgnition switch OFF
P1300Fuel cutIGF signal is detected for 6 consective ignitions
P1605Max. timing retardationReturned to normal condition
5. CHECK FOR INTERMITTENT PROBLEMS
TOYOTA hand−held tester only:
By putting the vehicle’s ECM in check mode, 1 trip detection logic is possible instead of 2 trip detection logic
and sensitivity to detect open circuits is increased. This makes it easier \
to detect intermittent problems.
(1) Clear the DTC (See step 2).
(2) Set the check mode (See step 3).
(3) Perform a simulation test (See page IN−18).
(4) Check the connector and terminal (See page IN−28).
(5) Handle the connector (See page IN−28).
(6) Visual check and contact pressure (See page IN−28).
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

−
DIAGNOSTICS ENGINE
DI−11
1996 LAND CRUISER (RM451U)
NG Proceed to page IG−1 and continue to trouble-
shoot.
OK
Proceed to matrix chart of problem symp-
toms on page DI−19.
7. ENGINE OPERATING CONDITION
NOTICE:
The values given below for ”Normal Condition” are representative valu\
es, so a vehicle may still be
normal even if its value varies from those listed here. So do not decide wheth\
er a part is faulty or
not solely according to the ”Normal Condition” here.
(a) CARB mandated signals.
TOYOTA hand−held tester displayMeasurement ItemNormal Condition*
FUEL SYS #1
Fuel System Bank 1
OPEN: Air− fuel ratio feedback stopped
CLOSED: Air− fuel ratio feedback operating
Idling after warming up: CLOSED
CALC LOAD
Calculator Load:
Current intake air volume as a proportion of max.
intake air volumeIdling: 13.8 − 19.3%
Racing without load (2,500 rpm): 17.6 − 25.2%
COOLANT TEMP.Engine Coolant Temp. Sensor ValueAfter warming up: 80 − 95° C (176 − 203°F)
SHORT FT #1Short−term Fuel Trim Bank 10 ± 20%
LONG FT #1Long−term Fuel Trim Bank 10 ± 20%
ENGINE SPDEngine SpeedIdling: 650 ± 50 rpm
VEHICLE SPDVehicle SpeedVehicle Stopped: 0 km/h (0 mph)
IGN ADVANCEIgnition Advance:
Ignition Timing of Cylinder No. 1Idling: BTDC 0 − 11°
INTAKE AIRIntake Air Temp. Sensor V alueEquivalent to Ambient Temp.
MAFAir Flow Rate Through Mass Air Flow Meter
Idling: 4.3 − 6.1 gm/sec.
Racing without load (2,500 rpm):
21.2 − 30.4 gm/sec.
THROTTLE POS
Voltage Output of Throttle Position Sensor
Calculated as a percentage:
0 V → 0%, 5 V →100%Throttle Fully Closed: 7 − 11 %
Throttle Fully Open: 65 − 75%
O2S B1, S1Voltage Output of Oxygen Sensor
Bank 1, Sensor 1Idling: 0.1 − 0.9 V
O2FT B1, S1Oxygen Sensor Fuel Trim Bank 1, Sensor 1
(Same as SHORT FT #1)0 ± 20%
O2S B1, S2Voltage Output of Oxygen Sensor
Bank 1, Sensor 2Driving (50 km/h, 31 mph): 0.1 − 0.9 V
∗: If no conditions are specifically stated for ”ldling”, it means \
the shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI−12
−
DIAGNOSTICS ENGINE
1996 LAND CRUISER (RM451U)
(b) TOYOTA Enhanced Signals.
TOYOTA hand−held tester displayMeasurement ItemNormal Condition*
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 rpm
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 0 g/r
INJECTORFuel injection time for cylinder No.1Idling: 2.0 − 3.5 ms
IAC STEP POSIntake Air Control Valve step position
Opening position step motor type IAC valveIdling: 10 − 50 step
STARTER SIGStarter SignalCranking: ON
CTP SWClosed Throttle Position Switch SignalThrottle Fully Closed: ON
A/C SIGA/C Switch SignalA/C ON: ON
PNP SWPark/Neutral Position Switch SignalP or N Position: ON
STOP LIGHT SWStop Light Switch SignalStop light switch ON: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL#1 − CYL#6Ratio of revolution variation for each cylinder
when variation is large0%
IGNITIONIgnition rate for all cylinders every 1,000 revolu-
tions0 − 3,000 rpm
EGRT GASEGR Gas Temp. Sensor V alueEGR not operating: Temp. between intake air
temp. and engine coolant temp.
EGR SYSTEMEGR System Operating ConditionIdling: OFF
FUEL PRES UP VSVFuel Pressure Up VSV SignalHigh temp. restarting: ON
FUEL PUMPFuel Pump SignalIdling: ON
TOTAL FT B1Total Fuel Trim Bank 1: Average value for fuel
trim system of bank 1Idling: 0.8 − 1.2 V
O2 LR B1, S1
Oxygen Sensor Lean Rich Bank 1, Sensor 1
Response time for oxygen sensor output to
switch from lean to rich
Idling after warmed up: 0 − 1,000 msec.
O2 RL B1, S1
Oxygen Sensor Rich Lean Bank 1, Sensor 1
Response time for oxygen sensor output to
switch from rich to lean
Idling after warmed up: 0 − 1,000 msec.
∗: If no conditions are specifically stated for ”ldling”, it means t\
he shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5OV−03
−
DIAGNOSTICS ENGINE
DI−13
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to \
the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, che\
ck the circuit for that code listed
in the table below. For details of each code, turn to the page referred to under the ’’See page ’’ for the respe-
cire ’’DTC No.’’ in the DTC chart.
DTC No.
(See Page)Detection ItemTrouble AreaMILMemory
P0100
( DI−20 )Mass Air Flow Circuit
MalfunctionOpen or short in mass air flow meter circuit
 Mass air flow meter
 ECM
 *1
P0101
( DI−25 )Mass Air Flow Circuit
Range/Performance
Problem
Mass air flow meter *1
P0110
( DI−26 )Intake Air Temp. Circuit
MalfunctionOpen or short in intake air temp. sensor circuit
 Intake air temp. sensor
 ECM
 *1
P0115
( DI−30 )Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
 Engine coolant temp. sensor
 ECM
 *1
P0116
( DI−34 )Engine Coolant Temp. Circuit
Range/Performance ProblemEngine coolant temp. sensor
 Cooling system *1
P0120
( DI−35 )Throttle/Pedal Position
Sensor/Switch ”A” Circuit
MalfunctionOpen or short in throttle position sensor circuit
 Throttle position sensor
 ECM
 *1
P0121
( DI−39 )Throttle/Pedal Position
Sensor/Switch ”A” Circuit
Range/Performance Problem
Throttle position sensor *1
P0125
( DI−40 )Insufficient Coolant Temp. for
Closed Loop Fuel Control Open or short in heated oxygen sensor circuit
 Heated oxygen sensor *1
P0130
( DI−43 )Heated Oxygen Sensor Circuit
Malfunction (Bank 1 Sensor 1)Heated oxygen sensor
 Fuel trim malfunction *1
P0133
( DI−46 ) Heated Oxygen Sensor Circuit
Slow Response
(Bank 1 Sensor 1)
Heated oxygen sensor *1
P0135
( DI−47 ) Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 1)Open or short in heater circuit of heated oxygen sensor
 Heated oxygen sensor heater
 ECM
 *1
P0136
( DI−49 )Heated Oxygen Sensor Circuit
Malfunction
(Bank 1 Sensor 2)
Heated oxygen sensor *1
P0141
( DI−47 ) Heated Oxygen Sensor Heater
Circuit Malfunction
(Bank 1 Sensor 2)
Same as DTC No. P0135 *1
*1: MIL lights up
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010