airbag off TOYOTA LAND CRUISER 1996 J80 Workshop Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 1996, Model line: LAND CRUISER, Model: TOYOTA LAND CRUISER 1996 J80Pages: 1399, PDF Size: 41.35 MB
Page 317 of 1399
−
BODY INSTRUMENT PANEL
BO−77
1996 LAND CRUISER (RM451U)
15. REMOVE CENTER CLUSTER FINISH PANEL WITH
HEATER CONTROL ASSEMBLY
(a) Using a screwdriver, take off the 2 claws, then remove the
cup holder hole cover.
HINT:
Tape the screwdriver tip before use.
(b) Take off the ashtray.
(c) Remove the center cluster finish panel with heater control
assembly, then disconnect the connectors.
(d) Remove the 2 screws and heater control assembly from the center cluster finish panel.
16. REMOVE RADIO
17. REMOVE GLOVE COMPARTMENT DOOR
18. REMOVE SPEAKER PANEL AND SPEAKER
19. REMOVE FRONT AND REAR CONSOLE BOX
20. DISCONNECT AIRBAG CONNECTOR
(a) Remove the airbag connector from the airbag bracket.
NOTICE:
When handling the airbag connector , take care not to dam-
age the airbag wire harness.
(b) Disconnect the airbag connector.
21. REMOVE INSTRUMENT PANEL
(a) Remove the 5 screws and 9 bolts.
(b) Remove the instrument panel. Torque: 20 N·m (210 kgf·cm, 15 ft·lbf) for passenger
airbag bolts
22. REMOVE INSTRUMENT PANEL REINFORCEMENT
(a) Remove the 2 bolts and lower instrument panel reinforce-
ment.
(b) Remove the 2 bolts, 2 nuts and No. 1 brace.
(c) Remove the 4 bolts, 4 nuts and instrument panel rein- forcement.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 673 of 1399
DI5Q2−02
R13451
R13006
E1Tc
AT0716
Normal Code
ON
OFF 0.25
0.25
DI−240
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
PRE−CHECK
1. SRS WARNING LIGHT CHECK
(a) Turn the ignition switch to ACC or ON and check that the
SRS warning light lights up.
(b) Check that the SRS warning light goes out after approx. 6 seconds.
HINT:
When the ignition switch is at ACC or ON and the SRS
warning light remains on or flashes, the airbag sensor as-
sembly has detected a malfunction code.
If, after approx. 6 seconds have elapsed, the SRS warn-
ing light sometimes lights up or the SRS warning light
lights up even when the ignition switch is OFF, a short in
the SRS warning light circuit can be considered likely.
Proceed to ”SRS warning light system malfunction” on
page DI−274 , DI−276 .
2. DTC CHECK (Using diagnosis check wire)
(a) Output the DTC. (1) Turn the ignition switch to ACC or ON position andwait approx. 20 seconds.
(2) Using SST, connect terminals Tc and E1 of the
DLC1.
SST 09843−18020
(b) Read the DTC. Read the 2− digit DTC as indicated by the number of times
the SRS warning light blinks. As an example, the blinking
patterns, normal, 11 and 31 are as shown on the illustra-
tion.
Normal code indication
The light will blink 2 times per second.
Malfunction code indication
The first blinking output indicates the first digit
of a 2−digit DTC. After a 1.5 second pause,
the second blinking output will indicate the
second digit.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 676 of 1399
DI5Q3−02
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−243
1996 LAND CRUISER (RM451U)
DIAGNOSTIC TROUBLE CODE CHART
If a malfunction code is displayed during the DTC check, the circuit listed for that code in t\
he table below
(Proceed to the page given for that circuit.).
DTC No.
(See Page)Detection ItemTrouble AreaSRS
Warning Light
Normal
( DI−271 )System normal−OFF
Source voltage dropBattery
Airbag sensor assemblyON
11
( DI−247 )
Short in squib circuit (to ground)Steering wheel pad (D squib)
Front passenger airbag assembly (P squib )
Spiral cable
Airbag sensor assembly
Wire harness
ON
12
( DI−254 )
Short in squib circuit (to B+)Steering wheel pad (D squib)
Front passenger airbag assembly (P squib)
Spiral cable
Airbag sensor assembly
Wire harness
ON
14
( DI−260 )
Open in D squib circuitSteering wheel pad (D squib)
Spiral cable
Airbag sensor assembly
Wire harness
ON
31
( DI−265 )Airbag sensor assembly malfunctionAirbag sensor assemblyON
54
( DI−267 )Open in P squib circuitFront passenger airbag assembly (P squib)
Airbag sensor assembly
Wire harness
ON
HINT:
When the SRS warning light remains lit up and the DTC is the normal code\
, this means a source drop
voltage.
This malfunction is not stored in memory by the airbag sensor assembly a\
nd if the power source volt-
age returns to normal, the SRS warning light will automatically go out.
When 2 or more codes are indicated, the codes will be displayed in numer\
al order starting from the
lowest numbered code.
If a code not listed on the chart is displayed, the airbag sensor assemb\
ly is faulty.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 704 of 1399
R13678
Airbag Sensor
Assembly
Battery F/B
R/B No.2
2
2
1
1
36 4
6 10
9
S4
GR
B
W
L−R
B−L
B−R ACC
IG2
A
IGN
AM1
AM2
FL BLOCK
W−R
B−L
W−R
Ignition
Switch
B
EA2
EA2
4
11 3
CIG
J3 Junction
Connector
GR 4
33
S5 S5
S4
A
2 2
50A AM1
2
2
Short ConnectorGR
B−W
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−271
1996 LAND CRUISER (RM451U)
DTC Normal Source Voltage Drop
CIRCUIT DESCRIPTION
The SRS is equipped with a voltage −increase circuit (DC−DC converter) in the airbag sensor assembly in
case the source voltage drops.
When the battery voltage drops, the voltage −increase circuit (DC−DC converter) functions to increase the
voltage of the SRS to normal voltage.
The diagnosis system malfunction display for this circuit is different to other circuits −when the SRS warning
light remains lit up and the DTC is a normal code, source voltage drop is ind\
icated.
Malfunction in this circuit is not recorded in the airbag sensor assembly, and the source voltage returns to
normal, the SRS warning light automatically goes off.
DTC No.DTC Detection ConditionTrouble Area
NormalSource voltage dorp Battery
Airbag sensor assembly
WIRING DIAGRAM
DI5QC−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 706 of 1399
H00003
ON
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−273
1996 LAND CRUISER (RM451U)
3 Does SRS warning light turn off?
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Connect steering wheel pad connector.
(c) Connect front passenger airbag assembly connector.
(d) Connect airbag sensor assembly connector.
(e) Turn ignition switch ON.
CHECK:
Operate electric system (defogger, wiper, headlight, heater
blower, etc.) and check that SRS warning light goes off.
NO Check DTC, if a DTC is output, perform trouble-
shooting according to DTC, if a normal code is
output, replace airbag sensor assembly.
YES
From the results of the above inspection, the malfunctioning part can now be \
considered normal.
To make sure of this, use the simulation method to check.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 707 of 1399
R13679
BatteryFL BLOCK 2
MAIN
W
W
ECU−B
1
F/B
S7
B−R
2
3
SRS Warning
Light
8LA
Tc
B−Y8
IH1 Airbag Sensor
Assembly
DLC1
5 W−L
11
GENERATOR
(ALTERNATOR)
W
Cruise Control ECU
W−L
W−L
B−Y
B−Y
IH1 S7 S6
S6
Short Connector
Short Connector W−L
B−L
11
12
3
EA3 11
22
7
DI−274
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
1996 LAND CRUISER (RM451U)
SRS Warning Light System Malfunction (Always lit up, when igni-
tion switch is in LOCK position.)
CIRCUIT DESCRIPTION
The SRS warning light is located on the combination meter.
When the SRS is normal, the SRS warning light lights up for approx. 6 seconds after the \
ignition switch is
turned from LOCK position to ACC or ON position, and then turns off automatically.
If there is a malfunction in the SRS, the SRS warning light lights up to\
inform the driver of the abnormality.
When terminals Tc and E1 of the DLC1 are connected, the DTC is displayed by the blinking\
of the SRS warn-
ing light.
WIRING DIAGRAM
DI5QD−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 708 of 1399
H00094
Airbag Sensor
Assembly
Spiral
Cable
P squib
D squib LOCK
AB0117
N12639
H00026
Airbag Sensor Assembly
LOCK
−
DIAGNOSTICS SUPPLEMENTAL RESTRAINT SYSTEM
DI−275
1996 LAND CRUISER (RM451U)
INSPECTION PROCEDURE
1 Preparation.
PREPARATION:
(a) Disconnect negative ( −) terminal cable from the battery,
and wait at least 90 seconds.
(b) Remove steering wheel pad. (See SR section)
(c) Disconnect connector of front passenger airbag assem- bly. (See page RS−22 )
CAUTION:
Store the steering wheel pad with the front surface facing
upward.
2 Does SRS warning light turn off?
PREPARATION:
(a) Turn ignition switch to LOCK.
(b) Disconnect negative ( −) terminal cable from the battery,
and wait at least 90 seconds.
(c) Disconnect airbag sensor assembly connector.
(d) Connect negative (−) terminal cable to battery.
CHECK:
Check operation of SRS warning light.
NO Check SRS warning light circuit or terminal AB circuit of DLC1.
YES
Replace airbag sensor assembly.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010
Page 1026 of 1399
RS0P0−01
AB0250Spiral Cable
R13451
RS−2
−
SUPPLEMENTAL RESTRAINT SYSTEM SRS AIRBAG
1996 LAND CRUISER (RM451U)
OPERATION
1. STEERING WHEEL PAD (with AIRBAG)
The inflater and bag of the SRS are stored in the steering wheel
pad and cannot be disassembled. The inflater contains a squib,
igniter charge, gas generant, etc., and inflates the bag when
instructed by the airbag sensor assembly.
2. SPIRAL CABLE (in COMBINATION SWITCH)
A spiral cable is used as an electrical joint from the vehicle body
side to the steering wheel.
3. FRONT PASSENGER AIRBAG ASSEMBLY
The inflater and bag of the SRS are stored in the front passen-
ger airbag assembly and cannot be disassembled.The inflater
contains a squib, igniter charge, gas generant, etc., and inflates
the bag when instructed by the airbag sensor assembly.
4. SRS WARNING LIGHT
The SRS warning light is located on the combination meter. It
goes on to alert the driver of trouble in the system when a mal-
function is detected in the airbag sensor assembly. In normal
operating condition when the ignition switch is turned to the
ACC or ON position, the light goes on for about 6 seconds and
then goes off.
5. AIRBAG SENSOR ASSEMBLY
The airbag sensor assembly is mounted on the floor inside the
console box. The airbag sensor assembly consists of an airbag
sensor, safing sensor, diagnosis circuit and ignition control,
drive circuit, etc.
It receives signals from the airbag sensors and judges whether
the SRS must be activated or not.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010