oil capacity TOYOTA LAND CRUISER 1996 J80 Workshop Manual

Q07308
AT3417
OK if hot
Add if hot
AT4252
0 − 1 mm
Q07309
DI−138
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
(3) With the engine OFF, add new fluid through the oil
filler pipe.
Fluid type: ATF DEXRON ®II
Capacity:
Dry fill: 11.0 liters (11.6 US qts, 9.7 Imp. qts)
Drain and refill: 1.9 liters (2.0 US qts, 1.7 Imp. qts)
(4) Start the engine and shift the shift lever into all posi-
tions from P to L position and then shift into P posi-
tion.
(5) With the engine idling, check the fluid level. Add fluid up to the COOL level on the dipstick.
(6) Check the fluid level at the normal operating tem- perature 70 − 80° C (158 − 176°F) and add as nec-
essary.
NOTICE:
Do not overfill.
(d) Check the fluid leaks.
Check for leaks in the transmission.
If there are leaks, it is necessary to repair or replace O −rings,
Seal packings, oil seals, plugs or other parts.
(e) Inspect and adjust the throttle cable. (1) Check that the throttle valve is fully closed.
(2) Check that the inner cable is not slack.
(3) Measure the distance between the outer cable endand stopper on the cable.
Standard distance: 0 − 1 mm (0 − 0.04 in.)
If the distance is not standard, adjust the cable by the adjusting
nuts.
(f) Inspect and adjust the shift lever position. When shifting the shift lever from the N position to other
positions, check that the lever can be shifted smoothly
and accurately to each position and that the position indi-
cator correctly indicates the position.
If the indicator is not aligned with the correct position, carry out
the following adjustment procedures. (1) Loosen the nut on the control rod.
(2) Push the control rod fully rearward.
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

LU0KE−03
LU−2
−
LUBRICATION OIL AND FILTER
1996 LAND CRUISER (RM451U)
REPLACEMENT
CAUTION:
Prolonged and repeated contact with mineral oil will result
in the removal of natural fats from the skin, leading to dry-
ness, irritation and dermatitis. In addition, used engine oil
contains potentially harmful contaminants which may
cause skin cancer.Care should be taken, therefore, when
changing engine oil to minimize the frequency and length
of time your skin is exposed to used engine oil. Protective
clothing and gloves that cannot be penetrated by oil should
be worn. The skin should be thoroughly washed with soap
and water, or use water−less hand cleaner, to remove any
used engine oil. Do not used gasoline, thinners, or sol-
vents.In order to preserve the environment, used oil and
used oil filters must be disposed of only at designated dis-
posal sites.
1. DRAIN ENGINE OIL
(a) Remove the oil filler cap.
(b) Remove the oil drain plug, and drain the oil into a contain-
er.
2. REPLACE OIL FILTER
(a) Using SST, remove the oil filter. SST 09228−44011
(b) Check and clean the oil filter installation surface.
(c) Apply clean engine oil to the gasket of a new oil filter.
(d) Lightly screw the oil filter into place, and tighten it until the
gasket contacts the seat.
(e) Using SST, tighten it an additional 3/4 turn. SST 09228−44011
3. FILL WITH ENGINE OIL
(a) Clean and install the oil drain plug with a new gasket.
Torque: 25 N·m (250 kgf·cm, 18 ft·lbf)
(b) Fill with new engine oil. Oil grade:
See step 1 in oil pressure check
Capacity:
Drain and refill
w/ Oil filter change
7.2 liters (7.5 US qts, 6.3 lmp. qts)
w/o Oil filter change
6.9 liters (7.3 US qts, 6.1 lmp. qts)
Dry fill
8.0 liters (8.5 US qts, 7.0 lmp. qts)
(c) Reinstall the oil filler cap.
4. START ENGINE AND CHECK FOR LEAKS
5. RECHECK ENGINE OIL LEVEL
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

P22572
P22574B13834
Drain Plug
Drain Plug
MA0621B13835
Lubricating Positions: 1. Spider2. Slide Yoke1
2 1
MA−8
−
MAINTENANCE CHASSIS
48
Author: Date:
1996 LAND CRUISER (RM451U)
7. REPLACE TRANSFER AND DIFFERENTIAL OIL
(a) Remove the drain plug and drain the oil.
(b) Reinstall the drain plug securely.
(c) Add new oil until it begins to run out of the filler hole.
Oil drade and viscosity: See step 5.
Oil capacity:
Transfer oil
1.7 liters (1.8 US qts, 1.5 lmp. qts)
Front differential oil (w/o Differential lock)
2.8 liters (3.0 US qts, 2.5 lmp. qts)
Front differential oil (w/ Differential lock)
2.65 liters (2.8 US qts, 2.3 lmp. qts)
Rear differential oil
3.25 liters (3.4 US qts, 2.9 lmp. qts)
8. REPACK FRONT WHEEL BEARINGS (See pages SA−7 and SA−9 )
9. LUBE STEERING KNUCKLE CHASSIS AND PROPEL-
LER SHAFT
(a) Remove the screw plug from each steering knuckle and repack with lubricant.
Steering knuckle grease:
Molybdenum disulfide lithium base chassis grease
(NLGI No. 2)
(b) Reinstall the 2 screw plugs.
(c) Lubricate chassis components, referring to the lubrication
chart. Before pumping in grease, wipe off any mud and
dust on the grease fitting.
Grease grade:
Lithium base chassis grease (NLGI No. 2)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP30G−03
−
PREPARATION LUBRICATION
PP−19
1996 LAND CRUISER (RM451U)
LUBRICANT
ItemCapacityClassification
Engine oil
Dry fill
Drain and refill w/ Oil filter change
w/o Oil filter change
8.0 liters (8.5 US qts, 7.0 Imp. qts)
7.4 liters (7.8 US qts, 6.5 Imp. qts)6.9 liters (7.3 US qts, 6.1 Imp qts)
API grade SH, Energy −Conserving II multigrade
engine oil or ILSAC multigrade engine oil and
recommended viscosity oil, with SAE 5W −30 be-
ing preferred engine oil
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP2XX−01
PP−38
−
PREPARATION TRANSFER
1996 LAND CRUISER (RM451U)
LUBRICANT
ItemCapacityClassification
Transfer oil1.7 liters (1.8 US qts, 1.5 lmp. qts)API GL− 4 or GL− 5
SAE 75W− 90
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP2YE−01
PP−50
−
PREPARATION SUSPENSION AND AXLE
1996 LAND CRUISER (RM451U)
LUBRICANT
ItemCapacityClassification
Differential oil
Front w/o Dfferential lock w/ Dfferential lock
Rear
2.80 liters (2.9 US qts, 2.5 lmp. qts)
2.65 liters (2.8 US qts, 2.3 lmp. qts)
3.25 liters (3.4 US qts, 2.9 lmp. qts)
Hypoid gear oil API GL− 5
Above − 18°C (0° F) SAE 90
Below − 18°C (0° F) SAE 80W− 90 or 80W
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

PP2Z1−01
PP−74
−
PREPARATION AIR CONDITIONING
1996 LAND CRUISER (RM451U)
LUBRICANT
ItemCapacityClassification
Compressor oil
When replacing receiver
When replacing condenser
When replacing evaporator
When replacing compressor
10 cc (0.35 fl.oz.) 40 cc (1.4 fl.oz.)
40 cc (1.4 fl.oz.)
120 cc (4.1 fl.oz.)
ND− OIL 8 or equivalent
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

SA1960
SST
RA1072
Filler Hole
Oil
0 − 5 mm (0 − 0.20 in.)
−
SUSPENSION AND AXLE FRONT DIFFERENTIAL REAR OIL SEAL
SA−23
1996 LAND CRUISER (RM451U)
(c) Apply light coat of gear oil on threads of a new companion
flange nut.
(d) Using SST to hold the flange, torque the nut.
SST 09330−00021
Torque: 196 N·m (2,000 kgf·cm, 145 ft·lbf)
14. ADJUST DRIVE PINION PRELOAD (See page SA−36 )
15. STAKE DRIVE PINION NUT
16. INSTALL FRONT PROPELLER SHAFT (See page PR−5 )
17. FILL DIFFERENTIAL WITH GEAR OIL Torque: 49 N·m (500 kgf·cm, 39 ft·lbf)
Oil type: Hypoid gear oil API GL −5
Recommended oil viscosity:
Above −18°C (0° F) SAE 90
Below −18°C (0° F) SAE 80W−90 or 80W
Capacity:
w/o Differential lock:
2.80 liters (2.9 US qts, 2.5 Imp. qts)
w/ Differential lock:
2.65 liters (2.8 US qts, 2.3 Imp. qts)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Z06905
Less than 5 mm
(10.20 in.)
−
SUSPENSION AND AXLE REAR DIFFERENTIAL FRONT OIL SEAL
SA−75
1996 LAND CRUISER (RM451U)
16. FILL DIFFERENTIAL WITH GEAR OIL
Torque: 49 N·m (500 kgf·cm, 39 ft·lbf)
Oil type: Hypoid gear oil API GL −5
Recommended oil viscosity:
Above −18°C (0° F) SAE 90
Below −18°C (0° F) SAE 80W−90 or 80W
Capacity:
3.25 liters (3.4 US qts, 2.9 Imp. qts)
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010