transmission wiring TOYOTA LAND CRUISER 1996 J80 Workshop Manual

P22487
No.1 Vehicle
Speed SensorCombination
Meter ECM
4−pulse
4−pulse
P22473
Combination Meter
3
C13 L−WL
−W8
E7 SPD ECM
5V
E1
From Cruise Control ECU
−
DIAGNOSTICS ENGINE
DI−87
1996 LAND CRUISER (RM451U)
DTC P0500 Vehicle Speed Sensor Malfunction
CIRCUIT DESCRIPTION
The vehicle speed sensor outputs a 4 − pulse signal for every revolution of the rotor shaft, which is rotated
by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectan-
gular wavefrom by the waveform shaping circuit inside the combination meter, it is then transmitted to the
ECM. The ECM determines the vehicle speed based on the frequency of thes\
e pulse signals.
DTC No.DTC Detecting ConditionTrouble Area
P0500
No vehicle speed sensor signal to ECM under conditions (a)
and (b):
(2 trip detection logic)
(a) Park/neutral position switch is OFF.
(b) Vehicle is being driven. Open or short in No.1 vehicle speed sensor circuit
 No.1 vehicle speed sensor
 Combination meter
 ECM
WIRING DIAGRAM
DI5PN−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

DI5KE−03
Vd762D00115
E4
11
12
13 1415
16
10 12
3
4
567
8
9
10
11
12
123
456
7
1
2
34
56
8910
11
7
8
9
12141516 13
17181920
21
22
23
242526
ECM T
erminals
1
23
4
5
6
7
89
10
11
13 12
15
16
171819202122 14
E5E6E7
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−145
1996 LAND CRUISER (RM451U)
TERMINALS OF ECM
Symbols (T erminal No.)Wiring ColorConditionSTD Voltage (V)
SPD (E7−8) − E1 (E4− 24)L− W − BR− B
Disconnect cruise control connector and IG ON StationaryBelow 1.5
Disconnect cruise control connector and IG ON
Turn one rear wheel slowlyPulse signal is outputBelow 1.5 ↔ 4 − 6
S1 (E4− 10) − E1 (E4− 24)R − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ON9 − 14
1st or 2nd gear9 − 14
3rd or O/D gearBelow 1.5
S2 (E4− 9) − E1 (E4− 24)R−Y − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ONBelow 1.5
2nd or 3rd gear9 − 14
1st or O/D gearBelow 1.5
SL (E4− 8) − E1 (E4− 24)R−L − BR− B
IG OFF Disconnect ECM connector11 − 15 Ω
IG ONBelow 1.5
Vehicle driving under lock −up position9 − 14
SP2+ (E6− 2) − SP− (E6− 8)V − V−G
IG OFF Disconnect ECM connector560 − 680 Ω
Engine is runningPulse signal is output
Below 1.5 ↔ 4 − 6
OD1 (E7− 18) − E1 (E4− 24)G−O − BR− BIG ON9 − 14
OD2 (E7− 19) − E1 (E4− 24)P−L − BR− BO/D main switch ON (O/D OFF)Below 3
O/D main switch OFF (O/D ON)9 − 14
OIL (E5− 12) − E2 (E5− 9)R−W − BR− BATF temperature: 110 °C (230° F)Below 1.5
L (E7−17) − E1 (E4− 24)G−W − BR− BIG ON Shift lever L position7.5 − 14
IG ON Shift lever other than L positionBelow 1.5
2 (E7−16) − E1 (E4− 24)O − BR− BIG ON Shift lever 2 position7.5 − 14
IG ON Shift lever other than 2 positionBelow 1.5
R (E7−15) − E1 (E4− 24)R−B − BR− BIG ON Shift lever R position7.5 − 14
IG ON Shift lever other than R positionBelow 1.5
NSW (E7−22) − E1 (E4− 24)B−W − BR− BIG ON Shift lever P or N positionBelow 3
IG ONShift lever other than P and N position9 − 14
STP (E7− 14) − E1 (E4− 24)G−W − BR− BIG ON Brake pedal is depressed7.5 − 14
IG ON Brake pedal is releasedBelow 1.5
THW (E5−4) − E2 (E5− 9)R−W − BR− BIG ON Engine coolant temperature 80 °C (176° F)Below 1.5
IDL (E5− 11) − E2 (E5− 9)G−W − BR− BIG ON Accel. pedal is releasedBelow 1.5
IG ONAccel. pedal is depressed9 − 14
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q04346
ATF Temperature SensorOIL
E5
R−W
BR−B
1 2
E2
E5 ECM
12 9 4 −
6 V
DI−154
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
DTC P0710 Transmission Fluid Temperature Sensor Cir-
cuit Malfunction (ATF Temperature Sensor)
CIRCUIT DESCRIPTION
The ATF temperature sensor converts fluid temperature into resistance value w\
hich is input into the ECM.
DTC No.DTC Detecting ConditionTrouble Area
P0710
Either (a) or (b) is detected for 0.5 sec. or more
(a) Temp. sensor resistance is less than 79 Ω
(b) After the engine has been operating for 15 min. or more, the resistance at the temp. sensor is more than 156 k ΩOpen or short in ATF temp. sensor circuit
 ATF temp. sensor
 ECM
WIRING DIAGRAM
DI5KK−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07463
TransmissionFrom Cruise
Control ECU
W
R−YECM
1
2 B+
S1
B E4
R
S2
Shift Solenoid
Valve No. 2
B+
E4
EC2
EC2
Shift Solenoid
Valve No. 1
10
9
R
R−Y R−Y
1
2
Q07641
S2
S1
DI−158
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Measure resistance between terminal S1 or S2 of ECM and body ground.
PREPARATION:
Disconnect the connector from the ECM.
CHECK:
Measure the resistance between terminal S1 or S2 of the ECM
and body ground.
OK:
Resistance: 11 − 15 Ω
OK Check and replace ECM.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07464
Solenoid Valve SLTransmission
ECM
B+
R−L
3
EC2
Y 8
E4 SL
R−L
3
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−163
1996 LAND CRUISER (RM451U)
DTC P0773 Shift Solenoid E Electrical Malfunction
(Shift Solenoid Valve SL)
CIRCUIT DESCRIPTION
The shift solenoid valve SL is turned ON and OFF by signals from the ECM to control the hyd\
raulic pressure
acting on the lock−up relay valve, which then controls operation of the lock −up clutch.
Fail Safe Function:
If the ECM detects a malfunction, it turns the shift solenoid valve SL O\
FF.
DTC No.DTC Detecting ConditionTrouble Area
P0773Open or short in shift solenoid valve SL circuit for 1 time
(2 trip detection logic) Open or short in shift solenoid valve SL circuit
 Shift solenoid valve SL
 ECM
WIRING DIAGRAM
DI5KS−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07465
SP2−
1
2E6
ECM
No. 2 Vehicle Speed Sensor SP2
+
4
EC2
5
V
V−G EC2 E682
V
V−G
Q08227
SP2+SP2−
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−167
1996 LAND CRUISER (RM451U)
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check vehicle speed value or resistance between terminals SP2+ and SP2− of
ECM.
When using OBD II scan tool or T OYOTA hand−held tester:
PREPARATION:
(a) Remove the fuse box cover.
(b) Connect an OBD II scan tool or TOYOTA hand− held tes-
ter to the DLC3.
(c) Start the engine and turn the OBD II scan tool or T OYOTA
hand −held tester main switch ON.
CHECK:
Drive the vehicle and read vehicle speed value.
OK:
Vehicle speed matches tester speed value.
When not using OBD II scan tool or TOYOTA hand−held tes-
ter:
PREPARATION:
Disconnect the connector from the ECM.
CHECK:
Check the resistance between terminals SP2+ and SP2− of the
ECM.
OK:
Resistance: 560 − 680 Ω
OK Check and replace ECM.
NG
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08577D00180
ECM
Combination Meter
Battery
Park/Neutral
Position Switch
Fuse Block
Starter
From
Battery L
2
R
NSW
E717
16 15
C12
G−W
E7E7
E7
L
R
2
C12
C12
R−B R−B
G−W
O
O
IH2
B−W 22
43
1
2B−W
IG1
ST1 2 4
AM1
2
2
2 2
1
2
AM1
3
J4
EA2 1 8
GAUGE
W
B F6
FLAM1
B+
IH2
IH1 IH1
B−L
B
6
Ignition Switch
4 R/B No. 2
6
6
B
B
Y
Y
15
B−R
B−WO
G−R R−B
S1
S2
10 4
11
2
3
21 7
Y
B−Y 1
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−169
1996 LAND CRUISER (RM451U)
DTC P1780 Park/Neutral Position Switch Malfunction
CIRCUIT DESCRIPTION
The park/neutral position switch detects the shift lever position and sends\
signals to the ECM.
The ECM receives signals (NSW, R, 2 and L) from the park/neutral position switch. When the signal is\
not
sent to the ECM from the park/neutral position switch, the ECM judges th\
at the shift lever is in D position.
DTC No.DTC Detection ConditionTrouble Area
P1780
2 or more switches are ON simultaneously for N, 2 and L posi-
tions (2 trip detection logic)
Short in park/neutral position switch circuit
 Park/neutral position switch
 ECMWhen driving under conditions (a), (b) and (c) for 30 sec. or
more, the park/neutral position switch is ON (N position)
(2 trip detection logic)
(a) Vehicle speed: 70 km/h (44 mph) or more
(b) Engine speed: 1,500 − 2,500 rpm
(c) Engine load: 0.6 g/rev. or more
WIRING DIAGRAM
DI5KY−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q07467
Cruise Control ECUOD OD1B+
G−O
9 18ECM
E7
BE3840
Q07658 D00091
ON
(−) (+) OD1
DI−172
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
O/D Cancel Signal Circuit
CIRCUIT DESCRIPTION
While driving with cruise control activated, in order to minimize gear shifting and provide\
smooth cruising on
an uphill, overdrive may be prohibited temporarily in some conditions.
The cruise control ECU sends O/D cut signals to the ECM as necessary and\
the ECM cancels overdrive
shifting until these signals are discontinued.
(For details, see the Cruise Control section, page DI−292)
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check voltage between terminal OD1 of ECM and body ground.
PREPARATION:
Turn the ignition switch ON.
CHECK:
Measure the voltage between terminal OD1 of the ECM and
body ground.
OK:
Voltage: 9 − 14 V
OK Proceed to next circuit inspection shown on problem symptoms table (See page DI−147 ).
NG
DI5L0−02
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08582
ECM
O/D OFF Indicator Light
(Combination Meter)
Ignition Switch
Fuse BlockO/D Main Switch* E7
2
P−L
B−L Y
GAUGE
Battery B+
W
2
Y
3 2
4 4
2
2 2
4
W−B
6
FL AM1
B−Y
22
E6 A
A
EA2 C12
C12
19
OD2
B ID2
J1
B 9
1
1 8
3
Fuse Block
P−L
P−L
AM1
2
BF
R/B No. 2 R/B No. 2
O/D Main switch
Contact go off with switch pushed in.
Contact go on with switch once again.
*:
DI−174
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
1996 LAND CRUISER (RM451U)
O/D Main Switch & O/D OFF Indicator Light Circuit
CIRCUIT DESCRIPTION
The O/D main switch contacts go off when the switch is pushed in and come on when it is pushed once again.\
In O/D main switch OFF position, the O/D OFF indicator lights up, and the \
ECM prohibits shifting to O/D.
WIRING DIAGRAM
DI5L3−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010

Q08584
ECM
Pattern Select Switch*
(PWR Mode Switch)
PWR
E7
P−B
B−W
PWR Indicator Light
(Combination Meter)
ID2
63
C12
13
16
20
15
B
J6
EGU−IG
Fuse Block
Ignition Switch
EA2
AM1
IG1
Fuse Block
AM1
P−B
P−B
6 B
B B ID2
B−W
B−W
3
1
B−Y
2
4
222
1 FL AM1
F6
Battery
2
2
3
4
WB −L
R/B No. 2
R/B No. 2
Pattern Select Switch (PWR Mode Switch)
When the PWR mode switch is pushed in, the switch is contacted and
the PWR mode is celected.
To cancel the PWR mode, push the PWR mode switch onec again.
*:
−
DIAGNOSTICS AUTOMATIC TRANSMISSION
DI−179
1996 LAND CRUISER (RM451U)
Pattern Select Switch Circuit (PWR Mode Switch)
CIRCUIT DESCRIPTION
The ECM memory contains the shift programs for the NORMAL and POWER pattern\
s, 2 position, L position
and the lock −up patterns. Following the programs corresponding to the signals from th\
e pattern select
switch, the park/neutral position switch and other various sensors, the ECM swi\
tches the solenoid valves
ON and OFF, and control the transmission gear change and the lock −up clutch operation.
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check operation of PWR indicator light.
PREPARATION:
Check if the PWR indicator light normally when the PWR mode switch is set to NORM and PWR position.
NG Check and repair PWR indicator light.
OK
DI5L6−03
Brought to you by BirfMark
Brought to you by BirfMark
Version 1.11 - 03/16/2010