door lock TOYOTA LAND CRUISER 1998 Factory Repair Manual

B16435
Ohmmeter
5
4
SF-8
- SFIFUEL PUMP
1707 Author
: Date
:
2004 LAND CRUISER (RM1071U)
Fuel pressure:
265 - 304 kPa (2.7 - 3.1 kgf/cm
2, 38 - 44 psi)
If pressure is higher than the specification, replace the fuel
pressure regulator.
If pressure is lower than the specification, check these parts:

Fuel hoses and connections

Fuel pump

Fuel filter

Fuel pressure regulator
(i) Disconnect the TOYOTA hand- held tester from the
DLC3.
(j) Start the engine.
(k) Measure the fuel pressure at idle.
Fuel pressure:
265 - 304 kPa (2.7 - 3.1 kgf/cm
2, 38 - 44 psi)
(l) Stop the engine.
(m) Check that the fuel pressure remains in the specification
below for 5 minutes after the engine stop.
Fuel pressure:
147 kPa (1.5 kgf/cm
2, 21 psi) or more
If the pressure is not as specified, check the fuel pump, pres-
sure regulator and/or the injectors.
(n) After checking the fuel pressure, disconnect the negative
(-) terminal cable from the battery and carefully remove
the SST to prevent gasoline from splashing.
SST 09268-45014
(o) Reinstall the front fuel pipe to the LH delivery pipe (See
page SF-27).
(p) Reconnect the negative (-) terminal cable to the battery.
(q) Check for fuel leaks (See page SF-1).
(r) Reinstall the V-bank cover with the 2 bolts and nuts.
(s) Reconnect the fuel return hose to the clamp on the V-
bank cover.
3. INSPECT FUEL PUMP
(a) Remove the No.1 rear seats.
(b) Remove the 2 rear door scuff plates, the step plates and
the rear seat lock covers.
(c) Pull off the front and rear floor carpets.
(d) Remove the 2 screws and the rear floor service hole cov-
er.
(e) Disconnect the fuel pump & sender gauge connector.
(f) Using an ohmmeter, measure the resistance between ter-
minal 4 and 5.

B16436
Battery
4 5
- SFIFUEL PUMP
SF-9
1708 Author
: Date
:
2004 LAND CRUISER (RM1071U)
Resistance: 0.2 - 3.0 W at 20°C (68°F)
If the resistance is not as specified, replace the fuel pump and/
or the lead wire.
(g) Inspect the fuel pump operation.
Connect the battery positive (+) lead to terminal 4 of the
connector, and the battery negative (-) lead to terminal 5.
Check that the fuel pump operates.
NOTICE:

These tests must be done quickly (within 10 seconds)
to prevent the coil burning out.

Keep the fuel pump as far away from the battery as
possible.

Always change the connection on the battery side.
If operation is not as specified, replace the fuel pump and/or
lead wire.
(h) Reconnect the fuel pump & sender gauge connector.
(i) Reinstall the rear floor service hole cover with the 2
screws.
(j) Reinstall the front and rear floor carpets.
(k) Remove the 2 rear door scuff plates, the step plates and
the rear sear lock covers.
(l) Reinstall the No.1 rear seats.

SF0XX-04
B16440
Pull
Enlarge
Tube Joint
Clip
B16441
Plug
Turn
Turn
- SFIFUEL PUMP
SF-13
1712 Author
: Date
:
2004 LAND CRUISER (RM1071U)
REMOVAL
CAUTION:
Do not smoke or work near an open frame when working
the fuel pump.
1. REMOVE NO.1 REAR SEATS
2. REMOVE REAR DOOR SCUFF PLATES, STEP
PLATES AND REAR SEAT LOCK COVERS
3. REMOVE REAR FLOOR SERVICE HOLE COVER
(a) Take off the front and rear floor carpets.
(b) Remove the 2 screws and rear floor service hole cover.
4. DISCONNECT FUEL PUMP & SENDER GAUGE CON-
NECTOR
5. DISCONNECT FUEL MAIN TUBE AND RETURN TUBE
(FUEL TUBE CONNECTORS) FROM FUEL SUCTION
PLATE
CAUTION:

Perform disconnecting operation of the fuel tube con-
nector (quick type) after reading the precautions.
(See page SF-1)

Prevent the retained pressure in the fuel line from
splashing inside the vehicle compartment.

Be careful not to damage the contact surface or let the
foreign matters on there when sealing the tube and
the suction plates with the quick connectors through
O-ring.

Be sure to perform the disconnection by hand. Do not
use tools.

Do not bend or turn the nylon tube by force.
(a) Before the operation, remove foreign matters or dirt stick-
ing to the tube joint clips.
(b) Enlarge the tip of the clips with fingers and pull them out
for disconnection.
(c) Pull out the fuel main tube and the return tube.
If the nylon tube and the suction plate stick together, ease the
connection by turning the nylon tube with fingers and pull it out
for disconnection.
NOTICE:
Plug the port of the fuel suction plate with a clean rubber
cap.
(d) After the disconnection, protect the connector with a plas-
tic bag.

H20933SST
SST
R13455
10 m (33 ft) or more
SSTBattery RS-62
- SUPPLEMENTAL RESTRAINT SYSTEMCURTAIN SHIELD AIRBAG ASSEMBLY
2337 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(b) Disconnect the curtain shield airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(c) Install the SST.
(1) Connect the connectors of the SST to the airbag
connector.
SST 09082-00700, 09082-00760
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(2) Move the SST at least 10 m (33 ft) away from the
front of the vehicle.
(3) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(4) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the battery negative
(-) terminal.
(d) Deploy the airbag.
(1) Check that no one is inside the vehicle or within 10
m (33 ft) area around the vehicle.
(2) Press the SST activation switch and deploy the air-
bag.
CAUTION:

The curtain shield airbag assembly is very hot when
the airbag is deployed, so leave it alone for at least 30
minutes after deployment.

Use gloves and safety glasses when handling the cur-
tain shield airbag assembly with the deployed airbag.

Do not apply water, etc. to the curtain shield airbag as-
sembly with the deployed airbag.

Always wash your hands with water after completing
the operation.

When scrapping a vehicle, deploy the airbag and
scrap the vehicle with the curtain shield airbag as-
sembly still installed.
HINT:
The airbag deploys as the LED of the SST activation switch
comes on.

H21095
H02169
H20924
SST
R13455
u"10 m (33 ft) or more
H03286
- SUPPLEMENTAL RESTRAINT SYSTEMFRONT PASSENGER AIRBAG ASSEMBLY
RS-35
2310 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(b) Disconnect the airbag connector.
(1) Remove the glove compartment door.
(2) Remove the No. 1 under cover.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(3) Pull up the connector.
(4) Disconnect the airbag connector.
(c) Install the SST.
(1) Connect the connector of SST to the front passen-
ger airbag assembly connector.
SST 09082-00700, 09082-00780
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(2) Move the SST at least 10 m (33 ft) away from the
front of the vehicle.
(3) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(4) Connect the red clip of the SST to the battery posi-
tive (+) terminal and the black clip to the negative (+)
terminal.
(d) Deploy the airbag.
(1) Check that no one is inside the vehicle, nor within
10 m (33 ft) area around the vehicle.
(2) Press the SST activation switch and deploy the air-
bag.
CAUTION:

The front passenger airbag assembly is very hot
when the airbag is deployed, so leave it alone for at
least 30 minutes after deployment.

H19942
H19943SST SST
R13455
10 m (33 ft) or more
SSTBattery
H19948
- SUPPLEMENTAL RESTRAINT SYSTEMSIDE AIRBAG ASSEMBLY
RS-49
2324 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(b) Disconnect the side airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
(c) Install the SST.
(1) Connect the connectors of the SST to the airbag
connector.
SST 09082-00700, 09082-00750
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock the secondary lock of the twin lock.
(2) Move the SST at least 10 m (33 ft) away from the
front of the vehicle.
(3) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(4) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the battery negative
(-) terminal.
(d) Deploy the airbag.
(1) Check that no one is inside the vehicle or within 10
m (33 ft) area around the vehicle.
(2) Press the SST activation switch and deploy the air-
bag.
CAUTION:

The side airbag assembly is very hot when the airbag
is deployed, so leave it alone for at least 30 minutes
after deployment.

Use gloves and safety glasses when handling the
side airbag assembly with the deployed airbag.

Do not apply water, etc. to the side airbag assembly
with the deployed airbag.

Always wash your hands with water after completing
the operation.

When scrapping a vehicle, deploy the airbag and
scrap the vehicle with the side airbag assembly still
installed.

H20953SST
R13455
10 m (33 ft) or more
SSTBattery
R06753
RS-22
- SUPPLEMENTAL RESTRAINT SYSTEMSTEERING WHEEL PAD AND SPIRAL CABLE
2297 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(7) Connect the connector of SST to the airbag con-
nector of the spiral cable.
SST 09082-00700, 09082-00780
NOTICE:
To avoid damaging the connector of the SST and wire har-
ness, do not lock the secondary lock of the twin lock.
(8) Move the SST at least 10 m (33 ft) away from the
front of the vehicle.
(9) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(10) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the negative (-) termi-
nal.
(c) Deploy the airbag.
(1) Confirm that no one is inside the vehicle nor within
10 m (33 ft) area around the vehicle.
(2) Press the SST activation switch and deploy the air-
bag.
CAUTION:

The steering wheel pad is very hot when the airbag is
deployed, so leave it alone for at least 30 minutes af-
ter deployment.

When moving a vehicle for scrapping which has a
steering wheel pad with deployed airbag, use gloves
and safety glasses.

Use gloves and safety glasses when handling a steer-
ing wheel pad with the deployed airbag.

Always wash your hands with water after completing
the operation.

Do not apply water, etc. to a steering wheel pad with
the deployed airbag.
HINT:
The airbag deploys as the LED of the SST activation switch
comes on.
2. DEPLOYMENT WHEN DISPOSING OF STEERING
WHEEL PAD ONLY
NOTICE:

When disposing of the steering wheel pad (with air-
bag) only, never use the customer's vehicle to deploy
the airbag.

Be sure to follow the procedure given below when de-
ploying the airbag.