airbag TOYOTA LAND CRUISER 1998 Factory User Guide

H18911
Instrument Panel Wire
Center Bracket
Front Passenger
Airbag Assembly
Defroster Nozzle
No. 1 Side Defroster
Nozzle Duct
No. 1 Heater to
Register Duct
No. 1 RegisterNo. 5 Heater to
Register DuctNo. 4 Register No. 2 Side Defroster
Nozzle Duct
G6.0 (61, 53 in.´lbf)
Instrument Panel
: Specified torqueN´m (kgf´cm, ft´lbf)
GGG
G
G
G
G
GG
G
G
6.0 (61, 53 in.´lbf)
BO-82
- BODYINSTRUMENT PANEL
2656 Author
: Date
:
2004 LAND CRUISER (RM1071U)

BO4IY-01
H18916
- BODYINSTRUMENT PANEL
BO-89
2663 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DISASSEMBLY
1. REMOVE NO. 2 SIDE DEFROSTER NOZZLE DUCT
2. REMOVE NO. 1 SIDE DEFROSTER NOZZLE DUCT
3. REMOVE DEFROSTER NOZZLE
4. REMOVE CENTER BRACKET
5. REMOVE NO. 1 HEATER TO REGISTER DUCT
6. REMOVE INSTRUMENT PANEL WIRE HARNESS
7. REMOVE NO. 5 HEATER TO REGISTER DUCT
8. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY
Remove the 3 nuts and the front passenger airbag assembly.
Torque: 6.0 N´m (61 kgf´cm, 53 in.´lbf)
CAUTION:

Do not store the front passenger airbag assembly
with the airbag deployment side facing down.

Never disassemble the front passenger airbag as-
sembly.
NOTICE:
At the time of reassembly, please refer to the following
items.

Make sure that the front passenger airbag assembly
is installed with the specified torque.

If the front passenger airbag assembly has been
dropped, or if there are cracks, dents or other defects
in the case or the connector, replace the front passen-
ger airbag assembly with a new one.

When installing the front passenger airbag assembly,
take care that the wiring does not interfere with other
parts and is not pinched between other parts.
9. REMOVE NO. 1 REGISTER
10. REMOVE NO. 4 REGISTER

BO3XU-02
H21208
Center Bracket
No. 5 Heater to
Register Duct
Airbag Connector
H18914
H21406
: 5 Clips
- BODYINSTRUMENT PANEL
BO-91
2665 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSTALLATION
1. INSTALL REINFORCEMENT
2. INSTALL NO. 1 BRACE
3. INSTALL FLOOR BRACE
4. INSTALL GLOVE COMPARTMENT DOOR DAMPER
5. INSTALL NO. 4 HEATER TO REGISTER DUCT
6. INSTALL NO. 3 HEATER TO REGISTER DUCT
7. INSTALL ECM (See page SF-60)
8. INSTALL INSTRUMENT PANEL
HINT:

Install the airbag connector between the No. 5 heater to
register duct and the center bracket temporarily, then
install the instrument panel.

Remove the airbag connector before installing the lower
No. 2 panel.
(a) Install the 6 bolts, the 2 nuts and the instrument panel,
then connect the connectors.
(b) Install the 2 bolts to the front passenger airbag assembly.
Torque: 20 N´m (204 kgf´cm, 15 ft´lbf)
(c) Connect the junction connectors.
HINT:
The connectors can be connected by tightening the bolts.
9. INSTALL FRONT CONSOLE BOX AND FRONT CON-
SOLE BOX BRACKET
Install the front console box and the front console box bracket
with the 2 bolts.
10. INSTALL CENTER LOWER CLUSTER FINISH PANEL
Connect the connector, then install the center lower cluster fin-
ish panel.

H21422
H21421
CA
C
B
- BODYINSTRUMENT PANEL
BO-93
2667 Author
: Date
:
2004 LAND CRUISER (RM1071U)
18. CONNECT AIRBAG CONNECTOR (See page RS-41)
19. INSTALL GLOVE COMPARTMENT DOOR
(a) Connect the glove compartment door damper clip, then
install the glove compartment door.
(b) Install the 2 screws.
20. INSTALL COMBINATION METER
(a) Check that the set-in connectors are connected securely
in the installation holes on the instrument panel.
(b) Place the combination meter on the instrument panel.
(c) Install the combination meter by tightening the screws,
ºAº, ºBº and ºCº in order.

H04808
H21420
H04807
H21418
BO-86
- BODYINSTRUMENT PANEL
2660 Author
: Date
:
2004 LAND CRUISER (RM1071U)
17. REMOVE NO. 2 HEATER TO REGISTER DUCT
Remove the screw and the No. 2 heater to register duct as
shown in the illustration.
18. REMOVE STEERING COLUMN
(See page SR-14 or SR-29)
19. REMOVE COMBINATION METER
(a) Disconnect the connectors.
HINT:
The connectors can be disconnected by loosening the bolts.
(b) Remove the 4 screws.
(c) Using a screwdriver, remove the combination meter.
HINT:
Tape up the screwdriver tip before use.
20. REMOVE GLOVE COMPARTMENT DOOR
(a) Remove the 2 screws.
(b) Remove the glove compartment door, then disconnect
the glove compartment door damper clip.
21. DISCONNECT AIRBAG CONNECTOR
(See page RS-31)
(a) Using a screwdriver, remove the No. 1 under cover.
HINT:
Tape up the screwdriver tip before use.
(b) Slide the airbag connector to pull out from the No. 1 under
cover.
(c) Disconnect the airbag connector.
NOTICE:
When handling the airbag connector, take care not to dam-
age the airbag wire harness.
22. REMOVE LOWER NO. 2 PANEL
Remove the 3 screws and the lower No. 2 panel.

BO1KP-04
H18921
Dome Light
Lens
Roof Headlining
Rear Trim
Roof Headlining Double Visor
Map Lamp
Center Pillar Garnish
Rear Mat
Set Plate
Striker Plate
Upper Roof
Side Inner Garnish Assist Grip
Cowl Side Trim Front Door Scuff Plate
Center Pillar Lower
Garnish CoverRear Door
Scuff PlateQuarter Trim PanelQuarter Trim
Jack Cover
Front Pillar Garnish Front Door
Opening TrimRear Door
Opening Trim Sun Visor
Holder
Assist Grip
Plug
Overhead
Console Box
Striker Plate
Center Pillar
Lower Garnish
Front Assist Grip
Front Assist Grip
Center Assist Gripw/ Curtain Shield Airbag:
42 (430, 31)
Adjustable
AnchorRear A/C Register
Rear A/C Register
Rear A/C Control Panel Rear A/C Register
Striker Plate
Striker Plate
Center Assist Grip
Center Assist Grip
Assist Grip
Rear
Assist Grip
x5Striker Plate
Center Assist Grip w/ Curtain Shield Airbag:
Adjustable
Anchor
Center Pillar Garnish
Center
Pillar
Garnish
: Specified torqueN´m (kgf´cm, ft´lbf)Rear Mat42 (430, 31)
Cap
Cap
Holder
rear
Assist Grip
w/ Curtain Shield Airbag:
Assist Grip
Assist Grip
Assist Grip Plug
w/ Curtain Shield Airbag:
Assist
Grip
Assist Grip Plug
Assist Grip
42 (430, 31)
Lens
Room Temperature
Sensor
BO-96
- BODYROOF HEADLINING
2670 Author
: Date
:
2004 LAND CRUISER (RM1071U)
ROOF HEADLINING
COMPONENTS

H05265
: 4 Clips
H21424
w/ Curtain Shield Airbag
w/o Curtain Shield Airbag
H21425
w/ Curtain Shield Airbag
w/o Curtain Shield Airbag
- BODYROOF HEADLINING
BO-99
2673 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(b) Using a screwdriver, remove the center pillar lower gar-
nish as shown in the illustration.
HINT:
Tape up the screwdriver tip before use.
(c) Use the same manner described above to the other side.
21. REMOVE CENTER PILLAR GARNISH
(a) Using a screwdriver, remove the seat belt anchor cover
cap.
HINT:
Tape up the screwdriver tip before use.
(b) Remove the bolt and the front seat outer belt shoulder an-
chor.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
(c) Using a clip remover, remove the clip.
(d) Using a screwdriver, remove the center pillar garnish.
HINT:
Tape up the screwdriver tip before use.
(e) Use the same manner described above to the other side.
22. REMOVE SUN VISOR
(a) Using a screwdriver, remove the caps.
HINT:
Tape the screwdriver tip before use.
(b) Remove the screws, then disconnect the connectors.
(c) Remove the sun visors.
23. REMOVE DOUBLE VISOR
Remove the screws and the double visors.
24. REMOVE HOLDER
Remove the screws and the holders.

H05268
H05270
H21423
4 Clips
H18926
BO-100
- BODYROOF HEADLINING
2674 Author
: Date
:
2004 LAND CRUISER (RM1071U)
25. REMOVE DOME LIGHT
(a) Using a screwdriver, remove the lens as shown in the il-
lustration.
HINT:
Tape up the screwdriver tip before use.
(b) Remove the 4 screws and the dome light, then disconnect
the connector.
26. REMOVE MAP LAMP
(a) Using a screwdriver, remove the lens as shown in the il-
lustration.
HINT:
Tape up the screwdriver tip before use.
(b) Remove the 4 screws and the map lamp, then disconnect
the connector.
27. REMOVE OVERHEAD CONSOLE BOX
(a) Remove the bolt.
(b) Using a screwdriver, remove the overhead console box,
then disconnect the connector.
HINT:
Tape up the screwdriver tip before use.
28. REMOVE REAR A/C CONTROL PANEL
Using a screwdriver, release the 4 claws and pull out the rear
A/C control panel, then disconnect the connector.
HINT:
Tape up the screwdriver tip before use.
29. REMOVE ROOM TEMPERATURE SENSOR
Using a scrwedriver, pull out the room temperature sensor, then
disconnect the connector.
HINT:
Tape up the screwdriver tip before use.
30. REMOVE ASSIST GRIPS
31. w/o Curtain Shield Airbag:
REMOVE CENTER ASSIST GRIPS
32. REMOVE ROOF HEADLINING
Using a clip remover, remove the 3 clips and the roof headlining.
33. REMOVE REAR A/C REGISTER
34. w/ Curtain Shield Airbag:
REMOVE ADJUSTABLE ANCHOR
Remove the 2 bolts and the adjustable anchor.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
35. w/ Curtain Shield Airbag:
REMOVE CENTER ASSIST GRIPS

BO1LL-02
AB0152
SST BO-144
- BODYSEAT BELT PRETENSIONER
2718 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DISPOSAL
HINT:
When scrapping vehicle equipped with an SRS or disposing of
a front seat outer belt (with seat belt pretensioner), always first
deploy the airbag in accordance with the procedure given in RS
section or activate the seat belt pretensioner. If any abnormality
occurs with the airbag deployment or seat belt pretensioner ac-
tivation, contact the SERVICE DEPT. of TOYOTA MOTORS
SALES, U.S.A., INC.. When disposing of a front seat outer belt
(with seat belt pretensioner) activated in a collision, follow the
same procedure given in step 1-(d) in ºDISPOSALº.
CAUTION:

Never dispose of front seat outer belt which has inac-
tivated pretensioner.

The seat belt pretensioner produces a sizeable ex-
ploding sound when it activates, so perform the op-
eration out-of-door and where it will not create a nui-
sance to nearby residents.

When activating the seat belt pretensioner, always
use the specified SST. (SRS Airbag Deployment Tool)
Perform the operation in a place away from electrical
noise.
SST 09082-00700, 09082-00740

When activating a front seat outer belt (with seat belt
pretensioner), perform the operation at least 10 m (33
ft) away from the front seat outer belt.

Use gloves and safety glasses when handling a front
seat outer belt with activated pretensioner.

Always wash your hands with water after completing
the operation.

Do not apply water, etc. to a front seat outer belt with
activated pretensioner.

AB0158
SSTBattery
AB0152
SST
AB0158
SSTBattery
H01580
SST
- BODYSEAT BELT PRETENSIONER
BO-145
2719 Author
: Date
:
2004 LAND CRUISER (RM1071U)
1. SEAT BELT PRETENSIONER ACTIVATION WHEN
SCRAPPING VEHICLE
HINT:
Have a battery ready as the power source to activate the seat
belt pretensioner.
(a) Check functioning of SST.
CAUTION:
When activating the seat belt pretensioner, always use the
specified SST: SRS Airbag Deployment Tool.
SST 09082-00700, 09082-00740
(1) Connect the SST to battery.
Connect the red clip of the SST to the battery posi-
tive (+) terminal and the black clip to the battery neg-
ative (-) terminal.
HINT:
Do not connect the yellow connector which will be connected
with the seat belt pretensioner.
(2) Check functioning of SST.
Press the SST activation switch, and check the LED
of the SST activation switch lights up.
CAUTION:
If the LED lights up when the activation switch is not being
pressed, SST malfunction is probable, so definitely do not
use the SST.
(b) Disconnect the pretensioner connector.
(1) Remove the front door scuff plate.
(2) Remove the front door opening trim.
(3) Remove the rear door scuff plate.
(4) Remove the rear door opening trim.
(5) Remove the center pillar lower garnish.