brake light TOYOTA LAND CRUISER 1998 Factory Repair Manual

BE-64
- BODY ELECTRICALCOMBINATION METER
2437 Author
: Date
:
C13 1 1 (CHECK E/G) G dIgnition switch ON and engine is stoppedBelow 1 VC13-1 1 (CHECK E/G) - GroundIgnition switch ON and engine is running10 - 14 V
C13-14 (CTR DIFF/4WD) - GroundIgnition switch ON and
center diff. lock switch OFFBelow 1 V
C13-14 (CTR DIFF/4WD) - GroundIgnition switch ON and
center diff. lock switch ON10 - 14 V
C13 15 (SLIP) G dIG switch ON, SLIP warning light ONBelow 1.5 VC13-15 (SLIP) - GroundIG switch ON, SLIP warning light OFF10 - 14 V
C13 16 (VSC TRC) G dIG switch ON, VSC TRC indicator light ONBelow 1.5 VC13-16 (VSC TRC) - GroundIG switch ON, VSC TRC indicator light OFF10 - 14 V
C13 17 (VSC OFF) G dIG switch ON, VSC OFF indicator light ONBelow 1.5 VC13-17 (VSC OFF) - GroundIG switch ON, VSC OFF indicator light OFF10 - 14 V
C13 18 (ACTIVE TRC) G dIG switch ON, TRC OFF indicator light ONBelow 1.5 VC13-18 (ACTIVE TRC) - GroundIG switch ON, TRC OFF indicator light OFF10 - 14 V
C13 19 (RSCA OFF) G dIG switch ON, RSCA warning light ONBelow 2.0 VC13-19 (RSCA OFF) - GroundIG switch ON, RSCA warning light OFF10 - 14 V
C14-4 (AIR BAG-) - GroundIgnition switch ON and
SRS indicator light lights upBelow 1 V
C14-4 (AIR BAG-) - GroundIgnition switch ON and
SRS indicator does not light up10 - 14 V
C14 7 (OIL PRS SDR) G dIgnition switch ON and indicator ONBelow 1 VC14-7 (OIL PRS SDR) - GroundIgnition switch ON and indicator OFF10 - 14 V
C14-10 (T/M PULSE) - GroundEngine is RunningPulse generation
C14 1 1 (D BKL SW) G dIgnition switch ON and seat belt is unfastened10 - 14 VC14-1 1 (D-BKL SW) - GroundIgnition switch ON and seat belt is fastenedBelow 1 V
C14 18 (PKB SW) G d
Ignition switch ON and
parking brake lever is pulledBelow 1 V
C14-18 (PKB SW) - GroundIgnition switch ON and
parking brake lever is released10 - 14 V
C14 20 (BRAKE) G d
Ignition switch ON and brake system indicator
ONBelow 1 V
C14-20 (BRAKE) - GroundIgnition switch ON and brake system indicator
OFF10 - 14 V
C15-1 (E/G EARTH) - GroundConstantContinuity
C15-2 (MAIN FE) - GroundConstantContinuity
C15-4 (MAIN FV) - GroundIgnition switch ON4.5 - 5.5 V
C15 6 (MAIN FR) G d
Ignition switch ON and
fuel sender gauge float UPApprox. 0.5 V
C15-6 (MAIN FR) - GroundIgnition switch ON and
fuel sender gauge float DOWNApprox. 5.5 V
C15 7 (ILL ) G d
Ignition switch ON and
light control rheostat volume minimumBelow 1 V
C15-7 (ILL-) - GroundIgnition switch ON and
light control rheostat volume maximum10 - 14 V
Key unlock warning switch ON (Key is inserted)Below 1 V
C15-9 (KEY SW) - GroundKey unlock warning switch OFF
(Key is removed)10 - 14 V

I06184
F
1/2
E 321
- BODY ELECTRICALCOMBINATION METER
BE-67
2440 Author
: Date
:
6. INSPECT FUEL SENDER GAUGE VOLTAGE
(a) Apply voltage (4.5 V - 5.0 V) between terminals 2 and 3.
(b) Measure voltage between terminals 1 and 2 for each float
position.
Float position mm (in.)Voltage (V)
F: Approx. 85.3 (3.36)Approx. 4.60 ± 0.1
1/2: Approx. 1.7 (0.67)Approx. 2.45 ± 0.1
E: Approx. 91.9 (3.62)Approx. 0.30 ± 0.1
If voltage value is not as specified, replace main sender gauge.
7. INSPECT LOW OIL PRESSURE WARNING LIGHT
(a) Disconnect the connector from the low oil pressure
switch.
(b) Turn the ignition switch ON.
(c) Connect the terminal of wire harness side connector and
ground, then check the warning light.
8. INSPECT PARKING BRAKE WARNING LIGHT
(a) Disconnect the connector from the parking brake switch
and ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
9. INSPECT BRAKE WARNING LIGHT
(a) Disconnect the connector from the brake fluid level warn-
ing switch and ground terminal on the wire harness side
connector.
(b) Turn the ignition switch ON and check that the warning
light lights up.
10. INSPECT BRAKE FLUID LEVEL WARNING SWITCH
(a) Remove the reservoir tank cap and retainer.
(b) Disconnect the connector.
(c) Check that the continuity exists between the terminal.
(d) Use syphon, etc., to take fluid out of the reservoir tank.
(e) Check that the continuity exists between terminals.
(f) Pour the fluid back in the reservoir tank.
11. INSPECT OPEN DOOR WARNING LIGHT
(a) DIsconnect the connector from the driver door courtesy
switch and ground terminal on the wire harness side con-
nector.
(b) Turn the ignition switch ON and check that the warning
light lights up.

BE0HH-12
I24743
I10004
Brake Master Cylinder

Brake Fluid Level Warning Switch
Cowl Side J/B LH

GAUGE1 Fuse

ACC FuseSeat Belt Buckle Switch
Parking Brake Switch Light Control RheostatCombination Meter Assembly
Ignition Switch
Cowl Side J/B RH

GAUGE2 Fuse

METER Fuse

DOME Fuse

ECU-B2 Fuse
BE-56
- BODY ELECTRICALCOMBINATION METER
2429 Author
: Date
:
2004 LAND CRUISER (RM1071U)
COMBINATION METER
LOCATION

- BODY ELECTRICALTROUBLESHOOTING
BE-3
2376 Author
: Date
:
2004 LAND CRUISER (RM1071U) Headlight does not come on.
1. Engine Room J/B Relay Circuit
2. Body ECU
3. Daytime Running Light No.3, 4 Relays
4. Headlight Dimmer Switch
5. Light Control Switch
6. Wire Harness
7. BulbBE-15
BE-32
BE-32
BE-32
BE-32
-
-
Headlight does not come on with light control switch in HEAD.1. Light Control Switch
2. Wire HarnessBE-32
-
Headlight does not go out with light control switch in OFF.1. Engine Room J/B Relay Circuit
2. Wire HarnessBE-15
-
Headlight flickers.1. Bulb
2. Wire Harness-
-
Headlight is dark.1. Bulb
2. Wire Harness-
-
Taillight does not come on with light control switch in TAIL.
1. Engine Room J/B Relay Circuit
2. Light Control Switch
3. Wire HarnessBE-15
BE-32
-
Taillight does not go out with light control switch in OFF.
1. Engine Room J/B Relay Circuit
2. Light Control Switch
3. Wire HarnessBE-15
BE-32
-
Headlight does not come on with engine running and light control
switch in OFF.
1. ECU-B1 Fuse
2. ECU-IG1 Fuse
3. Body ECU
4. Daytime Running Light No.3, 4 Relays
5. Generator L Terminal
6. Parking Brake Switch
7. Wire Harness-
-
BE-32
BE-32
CH-10
BE-63
-
FOG LIGHT SYSTEM:
SymptomSuspect AreaSee page
Fog light does not light up with light control SW HEAD
(Headlight is normal.)
1. FOG Fuse
2. Engine Room J/B Relay Circuit
3. Fog Light Switch
4. Wire Harness-
BE-15
BE-37
-
Fog light does not light up with light control SW HEAD
(Headlight does not light).1.*1 Other Parts
2. Wire Harness-
-
Only one light does not light up.1. Bulb
2. Wire Harness-
-
*1: Inspect Headlight System
TURN SIGNAL AND HAZARD WARNING SYSTEM:
SymptomSuspect AreaSee page
ºHazardº and ºTurnº do not light up.
1. ECU-IG2 Fuse
2. TURN HAZ Fuse
3. Ignitioin Switch
4. Turn Signal Flasher Relay
5. Wire Harness-
-
BE-29
BE-40
-
Hazard warning light does not light up.
(Turn is normal)1. Hazard Warning Switch
2. Wire HarnessBE-40
-
Turn signal does not light up.
(Hazard is normal)1. Turn Signal Switch
2. Wire HarnessBE-40
-

- BODY ELECTRICALTROUBLESHOOTING
BE-7
2380 Author
: Date
:
2004 LAND CRUISER (RM1071U) Seat belt warning light does not light up.
1. LED
2. Seat Belt Buckle Switch
3. Wire Harness
4. Body ECU-
BE-63
BE-63
DI-1038
Discharge warning light does not light up.
1. METER Fuse
2. LED
3. Wire Harness
4. Generator-
-
-
CH-2
Brake warning light does not light up.
1. LED
2. Parking Brake Switch
3. Brake Fluid Level Warning Switch
4. LED Check Relay
5. Combination Meter
6. Wire Harness-
BE-63
BE-63
BE-63
BE-58
-
SRS warning light does not light up.
1. ECU-B2 Fuse
2. LED
3. Airbag Sensor Assembly
4. Combination Meter
5. Wire Harness-
-
DI-690
BE-58
-
Open door warning light does not light up.
1. DOME Fuse
2. LED
3. Door Courtesy Switch
4. Combination Meter
5. Wire Harness-
-
BE-44
BE-58
-
A/T oil temperature warning light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. ECM-
BE-63
BE-58
DI-1
COMBINATION METER (Indicator Light):
SymptomSuspect AreaSee page
Cruise control indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. ECM-
BE-58
-
DI-1
High-beam indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. Headlight System-
BE-58
-
BE-30
Turn indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. Turn Signal and Hazard Warning System-
BE-58
-
BE-39
Shift indicator lights do not light up.
1. LED
2. Combination Meter
3. Park/Neutral Position Switch
4. Wire Harness-
BE-58
-
-
Only one shift indicator does not light up.1. LED
2. Combination Meter-
BE-58
Malfunction indicator light does not light up.
1. LED
2. Combination Meter
3. Wire Harness
4. ECM-
BE-58
-
DI-1

BO1KZ-04
BO0632
BO0633
15°
45°
- BODYSEAT BELT
BO-139
2713 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION
CAUTION:
Replace the seat belt assembly (outer belt, inner belt, bolts,
nuts or sill-bar) if it has been used in a severe impact. The
entire assembly should be replaced even if damage is not
obvious.
1. Except manual type:
RUNNING TEST (IN SAFE AREA)
(a) Fasten the front seat belts.
(b) Drive the car at 10 mph (16 km/h) and slam on the brakes.
Check that the belt locks and cannot be extended at this
time.
HINT:
Conduct this test in a safe area. If the belt does not lock, remove
the belt mechanism assembly and conduct the following static
check. Also, whenever installing a new belt assembly.
2. Driver 's seat belt (ELR):
STATIC TEST
(a) Make sure that the belt locks when pulled out quickly.
(b) Remove the locking retractor assembly.
HINT:
Before removing the pretensioner connector, be sure to read
the precautionary notice in the RS section.
(c) Tilt the retractor slowly.
(d) Make sure that the belt can be pulled out at a tilt of 15 de-
grees or less, and cannot be pulled out over 45 degrees
of tilt.
If a problem is found, replace the assembly.
3. Except driver's seat belt (ELR/ALR):
STATIC TEST
(a) Make sure that the belt locks when pulled out quickly.
(b) Remove the locking retractor assembly.
HINT:
Before removing the pretensioner connector, be sure to read
the precautionary notice in the RS section.
(c) Pull out the whole belt and measure the length of the
whole belt.
Then retract the belt slightly and pull it out again
(d) Make sure that the belt cannot be extended further.
If a problem is found, replace the assembly.

BR12E-07
F06425
TOYOTA
Hand-held
Tester
DLC3
BR-4
- BRAKEBRAKE FLUID
2140 Author
: Date
:
2004 LAND CRUISER (RM1071U)
BRAKE FLUID
BLEEDING
HINT:

If any work is done on the brake system or if air in the
brake lines is suspected, bleed the air from the system.

When bleeding, keep the amount of the fluid within the
line of reservoir between Min. and Max.
NOTICE:

Do not let brake fluid remain on painted surfaces.
Wash it off immediately.

With the reservoir cap removed, when depressing the
brake pedal, the fluid will spray.
1. FILL RESERVOIR WITH BRAKE FLUID
Fluid: SAE J1703 or FMVSS NO. 116 DOT3
2. In case of using TOYOTA hand-held tester:
BLEED HYDRAULIC BRAKE BOOSTER
HINT:
If the hydraulic brake booster has been disassembled, discon-
nect the brake line from the hydraulic brake booster or if the res-
ervoir becomes empty, bleed the hydraulic brake booster.
(a) Turn the ignition switch OFF, depress the brake pedal
more than 40 times.
HINT:
When a pressure in power supply system is released, reaction
force becomes light and stroke becomes longer.
(b) Turn the ignition switch ON, check that the pump stops af-
ter approx. 30 to 40 sec.
NOTICE:
When the pump does not stop, repeat step (a) and (b) again.
(c) With the ignition switch remained ON, depress the brake
pedal more than 20 times.
(d) Observe the procedure in step 4 and bleed the right and
left front brake caliper.
(e) Holding the brake pedal depressed, bleed the right and
left rear brake caliper.
HINT:
It is not necessary to depress the pedal continuously, as brake
fluid flows out by first depressing.
(f) Connect TOYOTA hand-held tester.
(1) Turn the ignition switch OFF, connect the TOYOTA
hand-held tester to DLC3.
(2) Turn the ignition switch ON and select ºAIR BLEED-
INGº on the TOYOTA hand-held tester.
HINT:
Please refer to the TOYOTA hand-held tester operator's manu-
al for further details.

F02821
Hydraulic Brake
BoosterSub-wire Harness S (SST)
AIR BLEED
FRONT
REAR BR-6
- BRAKEBRAKE FLUID
2142 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(b) Connect the actuator checker (SST) to the hydraulic
brake booster side wire harness via the sub-wire harness
(SST), as shown in the chart below.
SST 09990-00150, 09990-00480
HINT:
Connect the connector with the label of ºAIR BLEEDº attached
to the connector of actuator checker.
(c) Connect the red cable of the checker to the battery posi-
tive (+) terminal and the black cable to the negative (-) ter-
minal.
(d) Turn the ignition switch OFF, depress the brake pedal
more than 40 times.
HINT:
When a pressure in power supply system is released, reaction
force becomes light and stroke becomes longer.
(e) Turn the ignition switch ON, check that the pump stops af-
ter 30 to 40 sec.
NOTICE:
When the pump does not stop, repeat step (d) and (e) again.
(f) With the ignition switch remained ON, depress the brake
pedal more than 20 times.
(g) Observe the procedure in step 4 and bleed the right and
left front wheel caliper.
(h) Holding the brake pedal depressed, bleed the right and
left rear brake caliper.
HINT:
It is not necessary to depress the pedal continuously, as brake
fluid flows out by first depressing.

F04458
BR-8
- BRAKEBRAKE FLUID
2144 Author
: Date
:
2004 LAND CRUISER (RM1071U)
(l) Observe the procedure in step (k) and bleed left rear
brake line.
(m) Disconnect the actuator checker (SST) and sub-wire har-
ness (SST) from the actuator.
SST 09990-00150, 09990-00480
(n) Connect the 2 connectors to the hydraulic brake booster.
(o) Clear the DTC (See page DI-505).
4. BLEED BRAKE LINE
(a) Connect the vinyl tube to the brake caliper.
(b) Depress the brake pedal several times, then loosen the
bleeder plug with the pedal held down.
(c) At the point when fluid stops coming out, tighten the
bleeder plug, then release the brake pedal.
(d) Repeat (b) and (c) until all the air in the fluid has been bled
out.
(e) Repeat the above procedure to bleed the brake line for
each wheel.
Torque: 11 N´m (110 kgf´cm, 8 ft´lbf)
5. CHECK FLUID LEVEL IN RESERVOIR
(a) With the ignition switch OFF, depress the brake pedal
more than 40 times.
HINT:
When a pressure in power supply system is released, reaction
force becomes light and stroke becomes longer.
(b) Remove the reservoir cap. Add brake fluid up to the
ºMAXº line.
Fluid: SAE J1703 or FMVSS NO. 116 DOT3

BR0X9-02
F08309
Pedal Pad Brake PedalReturn Spring
Cowl Side TrimLower No. 1 PanelLH Lower Panel
No. 2 Heater to Register Duct
ABS ECU or
ABS & BA & TRAC
& VSC ECU
N´m (kgf´cm, ft´lbf): Specified torque
Cushion
Stop Light Switch
20 (200, 14)
Hydraulic Brake Booster Assembly
MP Grease
Front Door Scuff Plate
5.0 (51, 44 in.´lbf)
Clevis PinClip
- BRAKEBRAKE PEDAL
BR-1 1
2147 Author
: Date
:
2004 LAND CRUISER (RM1071U)
COMPONENTS