light TOYOTA LAND CRUISER 2002 J100 Navigation Manual

8
UNG604
1. Tune in the desired station.
2. Touch one of the station selector
switches (1-6) and hold it until a beep is
heard. This sets the station to the switch
and the frequency appears on the switch
Each switch can store FM1, FM2 and AM. To
change the preset station to a different one,
follow the same procedure.
The preset station memory is cancelled
when the power source is interrupted by bat-
tery disconnection or a blown fuse. Your vehicle has an electronic tuning radio
(ETR). T
une in the desired station using one
of the following methods.
Preset tuning: Touch the switch (1-6) or
push the º

º or ºº bu tto n of th e ºCHº button
for the station you want. The switch (1-6) is
highlighted in green and station frequency
appears on the display.
Manual tuning: Turn the ºTUNEº knob brief-
ly. Each time you turn the knob, the radio will
step up or down to another frequency.
Seek tuning: Push the º

º or ºº button of
the ºSEEKº button and hold it until you hear
a beep. The radio will begin seeking up or
down for a station of the nearest frequency
and will stop on reception. Each time you
push the button, the stations will be searched
out one after another.
UNG612
Scan tuning: Touch the ºSCANº switch
briefly. ºSCANº appears on the display. The
radio will find the next station up or down the
band, stay there for a few seconds, and then
scan again. To select a station, touch the
ºSCANº switch a second time.
(b) Presetting a station (c) Selecting a station

12To recall a radio text message, touch the
ºRECALLº
switch. Each time you touch the
switch, the message will be displayed from
the new one.
When you touch the ºOKº switch, the pre-
vious screen returns.
(a) Playing a cassette tape
unc614
When you insert a cassette tape, the ex-
posed tape should face to the right.
The player will automatically start when you
insert a cassette tape. At this time, ºTapeº
appears on the display.
If a metal or chrome equivalent cassette tape
is put in the cassette player, the player will
automatically recognize it and ºMTLº ap-
pears on the display.
To stop or eject the cassette tape, push the
º
º button.
UNG605
If a cassette is already in the slot, push the
ºTAPEº button.
Dolby  Noise Reduction* feature: If you
are listening to a tape that was recorded with
Dolby  B Noise Reduction, touch the switch
marked with the double
-D symbol. The
º switch will be highlighted in green.
Touch the switch again to turn off Dolby  B
NR.
The Dolby NR mode reduces tape noise by
about 10 dB. For best sound reproduction,
play your tapes with this switch on or off ac-
cording to the mode used for recording the
tape.
Cassette tape player operation

17
CAUTION
To reduce the chance of injury in case
of an accident or a sudden stop, always
keep the console box closed while driv-
ing.
(b) Playing a disc
ung627
Push the DISCº button if the magazine is
already loaded in the player.
DVD CHANGERº appears on the display.
The discs set in the magazine are played
continuously, starting with disc number 1.
The disc number of the disc currently being
played, the track number and the time from
the beginning of the program are shown on
the display. (c) Selecting a desired disc
unx609
On the screen: Touch the desired disc
number.
The selected disc number is highlighted in
green.
The player will start playing the selected disc
from the first track.
On the audio panel: Push the 

º or º
side of the DISCº button.
When you release the button, the player will
start playing the selected disc from the first
track.

18(d) Operating an audio CD
(i) Playing an audio CD
unx610
Push the number of the disc you want to
play. The selected disc is automatically
played. (ii) Selecting a desired track
UNC622a
TRACKº button: Use for direct access to
a desired track.
Push either side of the TRACKº
button and
hold it until the desired track number appears
on the display. As you release the button, the
player will start playing the selected track
from the beginning.
Fast forward: Touch the 
º switch and
hold it to fast forward the disc. When you re-
lease the switch, the player will resume play-
ing from that position.
Reverse: Touch the 
º switch and hold it
to reverse the disc. When you release the
switch, the player will resume playing. (iii) Searching for a desired track or a
disc
unx012
Touch the SCANº switch.
SCANº will be highlighted in green. The
player will play the next track for 10 seconds,
then scan again. To select a track, touch the
SCANº switch a second time. If the player
reaches the end of the disc, it will continue
scanning at track 1.

19
Touch the DISK SCANº switch.
DISC SCANº will be highlighted in green.
The program at the beginning of each disc
will be played for 10 seconds. To continue lis-
tening to the program of your choice, touch
the DISC SCANº switch a second time.
After all the audio disc are scanned in one
pass, normal play resumes.
(iv) Other functions
unx013
RPTº
switch: Use it for automatic repeat of
the track you are currently listening to.
Touch the switch while the track is playing.
When the track is finished, the player will au-
tomatically go back to the beginning of the
track and play the track again. To cancel it,
touch the switch once again.
DISC RPTº switch: Use it for automatic re-
peat of the disc you are currently listening to.
Touch the switch while the disc is playing.
When the disc is finished, the player will auto-
matically go back to the beginning of the disc
and play the disc again. To cancel it, touch
the switch once again. RANDº switch: Use it for automatic and
random selection of the disc which you are
currently listening to.
When the switch is touched, the system se-
lects a track in the disc you are currently lis-
tening
to. To cancel it, touch the switch once
again.
DISC RANDº switch: Use it for automatic
track selection for all the audio discs and play
by the system.
When the switch is touched, the system se-
lects a track in all the audio discs in the mag-
azine which is set and plays it. To cancel it,
touch the switch once again.

32For example, nearby buildings and terrain
can interfere with FM reception. Power lines
or telephone wires can interfere with AM sig-
nals. And of course, radio signals have a lim-
ited range, and the farther you are from a sta-
tion, the weaker its signal will be. In addition,
reception conditions change constantly as
your vehicle moves.
Here are some common reception
problems
that probably do not indicate a problem with
your radio:
FM
Fading and drifting stations - Generally,
the effective range of FM is about 40 km (25
miles). Once outside this range, you may no-
tice fading and drifting, which increase with
the distance from the radio transmitter. They
are often accompanied by distortion.
Multi-path - FM signals are reflective, mak-
ing it possible for two signals to reach your
antenna at the same time. If this happens,
the signals will cancel each other out, caus-
ing a momentary flutter or loss of reception.
Static and fluttering - These occur when
signals are blocked by buildings, trees, or
other large objects. Increasing the bass lev-
el may reduce static and fluttering. Station
swapping - If the FM signal you are
listening to is interrupted or weakened, and
there is another strong station nearby on the
FM band, your radio may tune in the second
station until the original signal can be picked
up again.
AM
Fading - AM broadcasts are reflected by the
upper atmosphere - especially at night.
These reflected signals can interfere with
those received directly from the radio station,
causing the radio station to sound alternately
strong and weak.
Station interference - When a reflected sig-
nal and a signal received directly from a radio
station are very nearly the same frequency,
they can interfere with each other, making it
difficult to hear the broadcast.
Static - AM is easily affected by external
sources of elec trical noise, such as high ten-
sion power lines, lightening, or electrical mo-
tors. This results in static.
Caring for your cassette player and tapes
For high performance from your cassette
player and tapes:
Clean the tape head and other parts regular-
ly. 
A dirty tape head or tape path can de-
crease sound quality and tangle your cas-
sette tapes. The easiest way to clean
them is by using a cleaning tape. (A wet
type is recommended.)
Use high-quality cassettes:
 Low-quality cassette tapes can cause
many problems, including poor sound, in-
consistent playing speed, and constant
auto-reversing. They can also get stuck
or tangled in the cassette player.
 Do not use a cassette if it has been dam-
aged or tangled or if its label is peeling off.
 Do not leave a cassette in the player if you
are not listening to it, especially if it is hot
outside.
 Store cassettes in their cases and out of
direct sunlight.
 Avoid using cassettes with a total playing
time longer than 100 minutes (50 minutes
per side). The tape used in these cas-
settes is thin and could get stuck or
tangled in the cassette player.

34
Your DVD player cannot play special
shaped, labeled or low-quality discs as
those shown here. Do not use them as
the player could be damaged.
 Handle discs carefully, especially when
you set them into the magazine. Hold
them on the edge and do not bend them.
Avoid getting fingerprints on them, partic-
ularly on the shiny side.
 Dirt, scrapes, warping, pin holes, or other
disc damage could cause the player to
skip or to repeat a section of a track. (To
see a pin hole, hold the disc up to the
light.)
 Remove discs from the DVD player when
you are not listening to them. Store them
in their plastic cases away from moisture,
heat, and direct sunlight.
To clean a disc: Wipe it with a soft, lint-free
cloth that has been dampened with water.
Wipe in a straight line from the center to the
edge of the disc (not in a circle). Do not use
a conventional record cleaner or anti-static
device.
CAUTION
DVD players use an invisible laser
beam which could cause hazardous
radiation exposure if directed outside
the unit. Be sure to operate the player
correctly.