navigation system TOYOTA LAND CRUISER 2003 J100 Navigation Manual

84
2003 Land Cruiser 100 Navigation (OM60A00U)
3UE002
2. Touch the “On” switch of the “Auto
reroute”. If you cannot find the item on
the list, touch
or switch to
scroll the list.
INFORMATION
If your vehicle leaves the guidance
route, the system searches for a new
route to the destination. The new route
may or may not take you back to the
previous route depending on how far
you are off the original guidance route.
When the estimated travel time feature is
turned on, the time required to reach the
destination is displayed on the Route
guidance screen.
1UE040
To turn the Estimated travel time on:
1. Push the
“MENU” switch to display
the Menu screen, and touch the “Set-
up” switch.
3UE003
2. Touch the “On” switch of the Esti-
mated travel time. If you cannot find the
item on the list, touch
or switch
and scroll the list.
Estimated travel time

88
2003 Land Cruiser 100 Navigation (OM60A00U)
3. Touch the “On” switch on the right of
Current street name.
The current street name appears on the Map
screen.
3UE011
3UE012T
This system has a function which informs
you of the time to replace certain parts or
components as well as other information
shown on the screen. (See “Information
items” on page 89.) When the system
begins operating after reaching either the
Information Item’s date or driving dis-
tance, the Information screen will be dis-
played.
The Information screen will not be displayed
again by touching the
“Do not display
this message again”
switch.
3UE013
1. Push the “INFO” button to display
the Information Menu screen. Touch the
“Maintenance” switch to display the
Maintenance screen.
2. Touch your desired icon and input the
conditions.
Maintenance information

89
2003 Land Cruiser 100 Navigation (OM60A00U)
3UE014
Date of notice: Input the next maintenance
date.
Distance of notice: Input the driving dis-
tance until the next maintenance check. You
can input a five−digit number for the driving
distance.
When you touch the
! switch on the
screen, the screen changes to display the
change name screen. Touch the keys to in-
put your desired name and then input the
conditions. After you input the information, touch the
“OK” switch. The screen then returns to
the Maintenance screen. The icon’s color will
change to green after the date or driving dis-
tance are input. The icon’s color will change
to orange when your vehicle needs to be ser-
viced. The following switches appear on the
Maintenance screen.
Delete all: Cancel all conditions which have
been input.
Reset all: Reset the item which has satisfied
either condition.
Touch the
“Off” switch of the Maintenance
screen, and the Information screen will no
longer be displayed.
INFORMATION
 For scheduled maintenance infor-
mation, please refer to the “Owner’s
Manual Supplement / Scheduled
Maintenance”.
 Depending on your driving or the
road conditions, the system may
have a timelag between the data
which has been input and the actual
date and driving distance.
Information items
Oil change
Replace oil filter
Rotate tires
Replace tires
Replace battery
Replace brake linings
Replace wiper blades
Replace engine coolant

93
2003 Land Cruiser 100 Navigation (OM60A00U)
3UE021T
2. A selected point will appear. Also, a
message will appear at the bottom of the
screen. To delete, touch the
“Yes”switch. To cancel the deletion, touch the“No” switch.
3UE022
This system has a function which informs
you of the memo you entered. When the
system begins operating after reaching
the memo’s date, the Information screen
will be displayed.
The Information screen will not be displayed
again by touching the
“Do not display
this message again”
switch.
3UE023
1. Push the “INFO” button on the bezel
to display the Information Menu screen.
2. Touch the
“Calendar” switch to dis-
play the Calendar screen.
Today’s date is circled in green. If today’s
date is not displayed on the screen, touch
“Today” switch to display a calendar of
this month.
Calendar with memo

98
2003 Land Cruiser 100 Navigation (OM60A00U)
The speech command system allows you
to operate the navigation system without
using your hands.
1. Push the speech command switch.
A beep sounds and an indicator is shown at
the top left of the display.
UNL302a
2. Give a command while an indicator is
shown in the display. (See ”Speech com-
mand list” on page 152.)
If the navigation system does not respond or
the confirmation screen does not disappear,
please push the speech command switch
and try again.
If no command is given, a beep sounds and
the indicator disappears 6 seconds later.
If the system does not recognize your
speech, the system will respond with this
message (“System does not recognize this
command, please rephrase your com-
mand.”). Start the operation from the begin-
ning.
 Microphone
It is unnecessary to speak directly into
the microphone when giving a command.
Speech command system

99
2003 Land Cruiser 100 Navigation (OM60A00U)
Speech command example: Searching
for a route to your home.
1. Push the speech command switch.
2. Say ”Go home”.
If your home is not registered, you will hear
”Home is not registered”.
3UE030
3. If you hear ”Are you sure that you want
a route to home?” (also shown on the dis-
play), push the speech command switch
and say ”Yes” .
If you say ”No”, the search will be canceled.
4. You will hear ”Calculating route to
home” and then the system starts
searching for a route.
INFORMATION
In the following conditions, the system
may not recognize the command prop-
erly.
 The command is not correct or clear.
 There are some noises such as wind
noise, etc.

102
2003 Land Cruiser 100 Navigation (OM60A00U)
Trip information such as driving time,
driving distance, average vehicle speed,
fuel consumption, etc. can be displayed
on the screen.
1. Push the
”INFO” button to display
the information menu screen.
UNG403a
2. To u c h t h e ”Trip Information”switch.
UNG401
Consumption
The consumption is calculated and dis-
played based on the driving distance and
the fuel consumption for 2 seconds with
engine running.
The value is updated every 2 seconds.
If you are driving at low speeds just before
stopping, the accurate figure way not be
shown.
After Refueling
The consumption after refueling is calcu-
lated and displayed based on the total
driving distance and the total fuel con-
sumption after refueling.
The value is updated every 10 seconds. When refueling, be
sure to stop your vehicle
and turn the ignition switch off.
Cruising Range
How far you can drive with the remaining
fuel is displayed.
Even though the display indicates sufficient
miles to run, if the fuel level on the fuel gauge
approaches ”E” or the low fuel level warning
light comes on, fill the fuel tank as soon as
possible.
INFORMATION
 When you first start driving your new
vehicle, the correct cruising range
may not be shown. One or more re-
fills of 10 gallons or more may be re-
quired for the system to set its cal-
ibration.
 The cruising range displayed is cal-
culated based on past fuel consump-
tion and may vary according to your
driving style and road condition.
Trip information

104
2003 Land Cruiser 100 Navigation (OM60A00U)
UNG405
Contrast and brightness adjustment
CONTRAST ”+”:
Strengthens the contrast of the screen.
CONTRAST ””:
Weakens the contrast of the screen.
BRIGHTNESS ”+”: Brightens the screen.
BRIGHTNESS ””: Darkens the screen.
The screen turns off when you push the
”SCREEN OFF”. To turn the display screen
back on, push any bezel switch such as
”INFO”, etc. The selected screen appears.
UNX401
Color and tone adjustment
You can adjust the color and the tone while
the DVD video and Video CD are being
played.
COLOR ”RED”:
Strengthens the red color of the screen.
COLOR ”GREEN”:
Strengthens the green color of the screen.
TONE ”+”: Strengthens the tone of the
screen.
TONE ””: Weakens the tone of the screen.
UNG407
Depending on the position of the head-
light switch, the screen changes to the
day mode or night mode.
To display the screen in the day mode even
with the head light switch on, touch ”DAY
MODE” on the adjustment screen for bright-
ness and contrast control.
However, if the instrument panel light control
switch is turned fully to the right, mode
switching cannot be done. It remains in the
day mode. In this case, ”DAY MODE” is not
shown on the screen.
If the screen is set in the day mode with the
headlight switch turned to on, this condition
is memorized in the system even with the en-
gine turned off.

11 0
2003 Land Cruiser 100 Navigation (OM60A00U)
If manual fan speed control is desired
 1Fan speed at low
2Fan speed at high
The fan speed can be set to your desired
speed by touching the appropriate air flow
control switch. The higher the fan speed is,
the more air is delivered. Pushing the ”OFF”
button turns of f the fan.
To remove exterior windshield frost, use the
high speed setting.
The selected mode is highlighted in green. If manual switching of air intake is de-
sired
UNC503
The air
intake control button is used to switch
the air intake between the OUTSIDE AIR
mode and RECIRCULATED AIR mode.
With the button in the OUTSIDE AIR mode,
the OUTSIDE AIR mode indicator light will
come on and the system will take fresh out-
side air into the vehicle.
If quick circulation of cooled air is desired,
push the air intake control button for RECIR-
CULATED AIR. The RECIRCULATED AIR
mode indicator light will come on. For normal use, it is best to keep the air in-
take control button set to OUTSIDE AIR
mode. If
recirculated air is used during heat-
ing, the windows will fog up more easily.
If the engine coolant temperature becomes
extremely high, the RECIRCULATED AIR
mode is automatically selected. This is not
a malfunction. When the engine coolant
temperature is lowered, the previous mode
resumes.

111
2003 Land Cruiser 100 Navigation (OM60A00U)
In the following cases, the RECIRCULATED
mode may change to the OUTSIDE AIR
mode automatically to prevent interior fog.
When the outside temperature becomes
lower than 4 C (39 F).
 When the air conditioning compressor
malfunctions.
 When the air conditioning cooler refriger-
ant decreases. If manual onoff of the air conditioning is
desired
Push the ”A/C”
switch to turn the air condi-
tioning on and push it again to turn the air
conditioning off.
If the outside temperature is lowered down to
around 0 C (32 F), the air conditioning will
turn off automatically.
If the system is used for ventilation, heating
in dry weather or removing frost or exterior
fog on the windshie ld, turn the air condition-
ing off once it is no longer required. This will
improve fuel economy. The air conditioning
can be used for year −round automatic tem-
perature control including cooling and dehu-
midifying operation.
UNC504
To remove interior fog on the windshield
Push the ”FRONT WINDSHIELD” button.
To remove frost or exterior fog on the
windshield
1. Push the upper side of the temperature control button until maximum figure ap-
pears on the temperature display.
2. Push the ”FRONT WINDSHIELD” but- ton.
(b) Windshield defogging and
defrosting