ESP TOYOTA LAND CRUISER 2007 J200 Navigation Manual

cxi
(b) Edit dealer
You can edit the dealer name, staff, loca-
tion and phone number.
1. Touch the
“Set Dealer” switch on
the “Maintenance” screen. The “Edit
Dealer” screen appears.
2. To edit, touch the corresponding
switch.
To edit “Dealer” or “Contact”
To input the name, touch the alphabet,
numeral and/or umlaut keys. You can in-
put up to 24 letters.
After inputting, touch the
“OK” switch at
the bottom right of the screen. The previous
screen will be displayed.

cxvii
(b) Adding a memo
To add a memo, touch the corresponding
date.
The “Memo” screen appears on the dis-
play. Touch the
“Add Memo” switch.
(See page cxiv for inputting a memo.)
You can add up to 100 memos.
(c) Deleting a memo
Touch the corresponding date. Touch
the corresponding memo switch, and
then touch the
“Delete” switch on the
screen. A message appears on the dis-
play. To delete, touch the
“Yes” switch.
To cancel the deletion, touch the
“No”
switch.
(d) Editing a memo
To edit a memo, touch the corresponding
date, and then touch the memo you wish
to edit.

cxix
To display the memos listed in a desired
period, touch the
“Period” switch.
Touch the number keys.
After setting the period, touch the
“OK”switch. The “Memo list” screen will be
displayed.
You can set a period from January 1, 2003,
through December 31, 2022, for searching.
To delete and/or edit the memo, touch the
desired memo switch.
To delete all memos, touch the
“Delete
All”
switch. A message appears on the
display. To delete, touch the “Yes”
switch. To cancel the deletion, touch the“No” switch.
To edit: Touch the corresponding
“Memo” or “Location” switch. (See
page cxvii for details.)
To delete: Touch the
“Delete” switch.
(See page cxvii for details.)

cxxiii
3Indicates the level of reception.

Too bad Excellent
The level of reception does not always corre-
spond with the one of your cellular phone.
4“A” is displayed when calling in ana-
logue.
“D” is displayed when calling in digital.
Not displayed when the system can get no
information from your cellular phone.
INFORMATION
This system supports the following
service.
HFP (Hands Free Profile) Ver. 1.0
OPP (Object Push Profile) Ver. 1.1
If your cellular phone does not support
HFP, you cannot enter the Bluetooth
phone, and take OPP service individu-
ally.
An antenna for the Bluetooth connec-
tion is built in the display. The indication
of the Bluetooth connection may turn
yellow and the system may not function
when you use the Bluetooth phone in
the following conditions and places.
Your cellular phone is hiding behind the
display (behind the seat or in the glove box
and console box).
Your cellular phone touches or covered
with metal materials.
Leave the Bluetooth phone on the place
where “Blue” indication is displayed.
Bluetooth is a trademark owned by Blue-
tooth SIG. Inc.
FCC ID: HYQBTA01A
IC ID: 1551ABTA01A
MADE IN JAPAN
This device complies with Part 15 of the
FCC Rules and RSS−210. Operation is
subject to the following two conditions: (1)
This device may not cause harmful inter-
ference, and (2) This device must accept
any interference received, including inter-
ference that may cause undesired opera-
tion.
CAUTION
Changes or modifications not express-
ly approved by the party responsible
for compliance could void the user’s
authority to operate the equipment.

cxxxix
Touch “YES” switch.
Touch
“NO” switch and the previous
screen appears.
Speech command system
The speech command system allows you
to operate the navigation system by giv-
ing a command.
UNL301
1. Push the speech command switch.
A beep sounds and on screen message is
displayed with an indicator at the top left.
2. Give a command while an indicator is
shown in the display. If you want to check
the command list, touch the
“Help”
switch to display the Help screen. (See
“Help screen” on page cxli.) When you
touch the
“Cancel”, the previous
screen returns.
If the navigation system does not respond or
the confirmation screen does not disappear,
please push the speech command switch
and try again.
If no command is given, a beep sounds and
the indicator disappears 6 seconds later.
If the system does not recognize your
speech, the system will respond with this
message (“System does not recognize this
command, please rephrase your com-
mand.”). Start the operation from the begin-
ning.

clxiv
(a) How to subscribe to an XM
satellite radio
An XM satellite radio is a tuner designed
exclusively to receive broadcasts provided
under a separate subscription. Availability is
limited to the 48 contiguous states.
How to subscribe:
You must enter into a separate service
agreement with the XM radio in order to re-
ceive satellite broadcast programming in the
vehicle. Additional activation and service
subscription fees apply that are not included
in the purchase price of the vehicle and op-
tional digital satellite tuner. For complete in-
formation on subscription rates and terms,
or to subscribe to the XM radio, visit XM on
the web at www.xmradio.com
or call an
XM’s Listener Care at (800) 967−2346.
The XM radio is solely responsible for the
quality, availability and content of the satel-
lite radio services provided, which are sub-
ject to the terms and conditions of the XM
radio customer service agreement.
Customers should have their radio ID ready;
the radio ID can be found by selecting the
“channel 000” on the radio. For details, see
the “Displaying the radio ID” that follows.
All fees and programming are the responsi-
bility of the XM satellite radio and are sub-
ject to change.Satellite tuner technology notice:
Toyota’s satellite radio tuners are awarded
Type Approval Certificates from XM Satel-
lite Radio Inc. on “March 10, 2003” and “April
15, 2003” as proof of compatibility with the
services offered by the XM satellite radio.
(b) Displaying the radio ID
Each XM tuner is identified with a unique
radio ID. You will need the radio ID when ac-
tivating XM service or when reporting a
problem.
If you select the “CH 000” using the “TUNE”
button, the ID code of 8 alphanumeric char-
acters appears. If you select another chan-
nel, display of the ID code is canceled. The
channel (000) alternates the display be-
tween the radio ID and the specific radio ID
code.
VI

clxix
NOTICE
This equipment has been tested and
found to comply with the limits for a
class B digital device, pursuant to
Part 15 of the FCC Rules. These limits
are designed to provide reasonable
protection against harmful interfer-
ence in a residential installation. This
equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause
harmful interference to radio commu-
nications. However, there is no guar-
antee that interference will not occur
in a particular installation.
If this equipment does cause harmful
interference to radio or television re-
ception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct
the interference by one or more of the
following measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between
the equipment and receiver.
– Connect the equipment into an out-
let on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experi-
enced radio/TV technician for help.
Information to user
Alternation or modifications carried
out without appropriate authorization
may invalidate the user’s right to op-
erate the equipment.NOTICE
This XM tuner supports “Audio Ser-
vices” (Music and Talk) of only XM
satellite radio and “Text Informa-
tion”, linked to the respective “Audio
Services”.
*Text Information includes, Station
Name, (Artist) Name, (Song) Title and
Category Name.

clxxi Autoreverse feature: After the cassette
player reaches the end of a tape, it automati-
cally reverses and begins to play the other
side, regardless of whether the cassette was
playing or fast forwarding.
(c) Automatic program selection
lxb006a
“RPT” switch: The repeat feature automati-
cally replays the current program.
Touch the “RPT” switch while the program
is playing. When the program ends, it will au-
tomatically be rewound and replayed.
Touch the switch again to turn off the repeat
feature.
There must be at least 3 seconds of blank
space between programs for the repeat fea-
ture to work correctly.
“SKIP” switch: The skip feature allows you
to fast forward past long stretches of blank
tape. This is especially useful at the end of
cassettes.
Touch the “SKIP” switch. The player will au-
tomatically skip any blank portions of 15 se-conds or more and play the next program.
To cancel it, touch the switch once again.

clxxxiii Code
Language
1001Japanese
0514English
0618French
0405German
0920Italian
0519Spanish
2608Chinese
1412Dutch
1620Portuguese
1922Swedish
1821Russian
111 5Korean
0512Greek
0101Afar
0102Abkhazian
0106Afrikaans
0113Amharic
0118Arabic
0119Assamese
0125Aymara
0126Azerbaijani
0201Bashkir
0205Byelorussian
0207Bulgarian
0208Bihari
0209Bislama
0214Bengali
0215Tibetan
0218Breton
0301Catalan
0315Corsican
0319Czach
0325Welsh
0401Danish
0426Bhutani
0515Esperanto
0520Estonian
0521Basque
0601Persian
0609Finnish
0610Fiji
0615Faroese
0625Frisian
0701Irish
0704Scots−Gaelic
0712Galician
0714Guarani
0721Gujarati
0801Hausa
0809Hindi
0818Croatian
0821Hungarian
0825Armenian
0901Interlingua
0905Interlingue
0911Inupiak
0914Indonesian
0919Icelandic
0923Hebrew
1009Yiddish
1023Javanese
1101Georgian
VI

cxc Static and fluttering − These occur when
signals are blocked by buildings, trees, or
other large objects. Increasing the bass lev-
el may reduce static and fluttering.
Station swapping − If the FM signal you are
listening to is interrupted or weakened, and
there is another strong station nearby on the
FM band, your radio may tune in the second
station until the original signal can be picked
up again.
AM
Fading − AM broadcasts are reflected by the
upper atmosphere − especially at night.
These reflected signals can interfere with
those received directly from the radio sta-
tion, causing the radio station to sound alter-
nately strong and weak.
Station interference − When a reflected
signal and a signal received directly from a
radio station are very nearly the same fre-
quency, they can interfere with each other,
making it difficult to hear the broadcast.
Static − AM is easily affected by external
sources of electrical noise, such as high ten-
sion power lines, lightening, or electrical mo-
tors. This results in static.Caring for your cassette player and tapes
For high performance from your cassette
player and tapes:
Clean the tape head and other parts regular-
ly.
A dirty tape head or tape path can de-
crease sound quality and tangle your cas-
sette tapes. The easiest way to clean them
is by using a cleaning tape. (A wet type is
recommended.)
Use high−quality cassettes:
Low−quality cassette tapes can cause
many problems, including poor sound, in-
consistent playing speed, and constant
auto−reversing. They can also get stuck or
tangled in the cassette player.
Do not use a cassette if it has been dam-
aged or tangled or if its label is peeling off.
Do not leave a cassette in the player if
you are not listening to it, especially if it is hot
outside.
Store cassettes in their cases and out of
direct sunlight.
Avoid using cassettes with a total playing
time longer than 100 minutes (50 minutes
per side). The tape used in these cassettes
is thin and could get stuck or tangled in the
cassette player.Caring for your multidisc player and
discs
Your multi−disc player is intended for use
with 12 cm (4.7 in.) discs only.
Extremely high temperature can keep
your multi−disc player from working. On hot
days, use air conditioning to cool the vehicle
interior before you listen to a disc.
Bumpy roads or other vibrations may
make your multi−disc player skip.
If moisture gets into your multi−disc play-
er, you may not hear any sound even though
your multi−disc player appears to be work-
ing. Remove the magazine from the player
and wait until it dries.
CAUTION
Multidisc players use an invisible
laser beam which could cause
hazardous radiation exposure if
directed outside the unit. Be sure to
operate the player correctly.