light TOYOTA LAND CRUISER 2007 J200 Navigation Manual

clvii
7wlc002a
Push the “AM”, “FM”, “TAPE” or “DISC”
button to turn on that mode. The selected
mode turns on directly.
Push these buttons if you want to switch
from one mode to another.
If the tape or disc is not set, the cassette
player or compact disc player does not turn
on.
You can turn off the cassette player by eject-
ing the cassette tape. If the audio system
was previously off, then the entire audio sys-
tem will be turned off when you eject the cas-
sette tape. If another function was previous-
ly playing, it will come on again.
lxb001a
lxb006a
lxb008a
The switches for radio, cassette tape and
disc player operation are displayed on
the liquid crystal display. Touch them
lightly and directly on the screen.
The selected switch is highlighted in green.

clxi
(b) Presetting a station
lxb001a
1. Tune in the desired station.
2. Touch one of the station selector
switches (16) and hold it until a beep is
heard. This sets the station to the switch
and the frequency appears on the switch.
Each switch can store FM1, FM2 and AM.
To change the preset station to a different
one, follow the same procedure.
The preset station memory is cancelled
when the power source is interrupted by bat-
tery disconnection or a blown fuse.
(c) Selecting a station
Your Toyota has an electronic tuning radio
(ETR). Tune in the desired station using one
of the following methods.
Preset tuning: Touch the switch (1−6) or
push the “
” or “” side of the “CH” button
for the station you want. The switch (1−6) is
highlighted in green and station frequency
appears on the display.
Manual tuning: Turn the “TUNE” knob brief-
ly. Each time you turn the knob, the radio will
step up or down to another frequency.
Seek tuning: Push the “
” or “” side of
the “SEEK” button and hold it until you hear
a beep. The radio will begin seeking up or
down for a station of the nearest frequency
and will stop on reception. Each time you
push the button, the stations will be
searched out one after another.
lxb001a
Scan tuning:Touch the “SCAN” switch
briefly. “SCAN” appears on the display. The
radio will find the next station up or down the
band, stay there for a few seconds, and then
scan again. To select a station, touch the
“SCAN” switch a second time.
Preset scan tuning: Touch the “SCAN”
switch and hold it until you hear a beep. “P.
SCAN” appears on the display. The radio
will tune in the next preset station up or down
the band, stay there for a few seconds, and
then move to the next preset station. To se-
lect a station, touch the “SCAN” switch a se-
cond time.

clxvi
(e) Selecting a channel
Tune in the desired channel using one of the
following methods.
Preset tuning: Touch the switch (1−6) or
push the “
” or “” button of the “CH” but-
ton for the channel you want. The switch
(1−6) is highlighted in green.
Manual tuning within the channel catego-
ry: Turn the “TUNE” knob. The radio will
step up or down the channel.
Manual tuning within the current channel
category: Push the “SEEK” button. The ra-
dio will step up or down the channel within
the current channel category. Touch the
“TYPE SEEK” switch. The radio will step up
the channel within the current channel cate-
gory.lc022
To scan the currently selected channel
category: Touch the “TYPE SCAN” switch
or push the “SCAN” button briefly. “SCAN”
appears on the display. The radio will find
the next channel in the same channel cate-
gory, stay there for a few seconds, and then
scan again. To select a channel, push the
“SCAN” button a second time.
To scan the preset channels: Touch the
“TYPE SCAN” switch or push the “SCAN”
button and hold it until you hear a beep.
“P.SCAN” appears on the display. The radio
will find the next preset channel, stay there
for a few seconds, and then move to the next
preset channel. To select a channel, push
the “SCAN” button a second time.
(f) Channel category
lc023
Touch either “” or “” switch to switch to the
next or previous category.
VI

clxx
Cassette tape player
operation
(a) Playing a cassette tape
7ulc008a
When you insert a cassette tape, the ex-
posed tape should be to the right.
The player will automatically start when you
insert a cassette tape. At this time, “Tape”
appears on the display.
If a metal or chrome equivalent cassette
tape is put in the cassette player, the player
will automatically adapt to it and “MTL” ap-
pears on the display.
To stop or eject the cassette tape, push the
“
” button.
lxb006a
If a cassette is already in the slot, push
the “TAPE” button.
Dolby Noise Reduction* feature: If you
are listening to a tape that was recorded with
Dolby B Noise Reduction, touch the “
”
switch. The “
” switch will be highlighted
in green. Touch the switch again to turn off
Dolby B NR.
The Dolby NR mode reduces tape noise by
about 10 dB. For best sound reproduction,
play your tapes with this switch on or off ac-
cording to the mode used for recording the
tape.
* Dolby noise reduction manufactured under
license from Dolby Laboratories Licensing
Corporation. “DOLBY” and the double−D
symbol
are trademarks of Dolby Labo-
ratories Licensing Corporation.
(b) Manual program selection
Reverse switch: You can reverse the tape
by touching the “” switch or “PROG”
button. The display will show the opposite
direction after reversing the tape. Also if the
tape reaches the end of one side, it is auto-
matically reversed to the other side.
Fast forward and Rewind switches: Yo u
can fast forward or fast rewind by touching
the “” or “” switch.
To stop the tape while it is fast forwarding,
touch “”, to stop the tape while it is re-
winding, touch “”.
If a tape rewinds completely, the cassette
player will stop and then play the same side.
If a tape fast forwards completely, the cas-
sette player will play the other side of the
tape using the auto−reverse feature.
VI

clxxiv When the magazine is set completely, the
system will be in a “Load” cycle for approxi-
mately 30 seconds while the system
searches for discs in the magazine. Upon
completion of this cycle, the DVD player unit
will be ready to play. If the “DISC” button is
pushed during the “Load” cycle, “LOAD” ap-
pears on the display until the system has
completed the load cycle, after which the
system will begin normal play.
CAUTION
To reduce the chance of injury in case
of an accident or a sudden stop, always
keep the console box closed while
driving.
(b) Playing a disc
ung627
Push the “DISC” button if the magazine is
already loaded in the player.
The “DVD CHANGER” screen appears on
the display.
The discs set in the magazine are played
continuously, starting with disc number 1.
The disc number of the disc currently being
played, the track number and the time from
the beginning of the program are shown on
the display.
(c) Selecting a desired disc
On the screen: Touch the desired disc
number.
The selected disc number is highlighted in
green.
The player will start playing the selected disc
from the first track.
On the audio panel: Push the “
” or “”
side of the “DISC” button.
When you release the button, the player will
start playing the selected disc from the first
track.VI

clxxv
(d) Operating an audio CD
(i) Playing an audio CD
lxb008a
Push the “AUDIO” button to display this
screen. You can operate the switches
and choose the number of the disc you
want to play. The selected disc is auto-
matically played.(ii) Selecting a desired track
“TRACK” button: Use for direct access to
a desired track.
Push either side of the “TRACK” button and
hold it until the desired track number ap-
pears on the display. As you release the but-
ton, the player will start playing the selected
track from the beginning.
Fast forward: Touch the “
” switch and
hold it to fast forward the disc. When you re-
lease the switch, the player will resume play-
ing from that position.
Reverse: Touch the “
” switch and hold it
to reverse the disc. When you release the
switch, the player will resume playing.(iii) Searching for a desired track or a
disc
lxb008a
Touch the “SCAN” switch.
“Scan” will be highlighted in green. The play-
er will play the next track for 10 seconds,
then scan again. To select a track, touch the
“SCAN” switch a second time. If the player
reaches the end of the disc, it will continue
scanning at track 1.
After all the tracks are scanned in one pass,
normal play resumes.
Touch the “DISK SCAN” switch.
“DISC SCAN” will be highlighted in green.
The program at the beginning of each disc
will be played for 10 seconds. To continue
listening to the program of your choice,
touch the “DISC SCAN” switch a second
time.

cxc Static and fluttering − These occur when
signals are blocked by buildings, trees, or
other large objects. Increasing the bass lev-
el may reduce static and fluttering.
Station swapping − If the FM signal you are
listening to is interrupted or weakened, and
there is another strong station nearby on the
FM band, your radio may tune in the second
station until the original signal can be picked
up again.
AM
Fading − AM broadcasts are reflected by the
upper atmosphere − especially at night.
These reflected signals can interfere with
those received directly from the radio sta-
tion, causing the radio station to sound alter-
nately strong and weak.
Station interference − When a reflected
signal and a signal received directly from a
radio station are very nearly the same fre-
quency, they can interfere with each other,
making it difficult to hear the broadcast.
Static − AM is easily affected by external
sources of electrical noise, such as high ten-
sion power lines, lightening, or electrical mo-
tors. This results in static.Caring for your cassette player and tapes
For high performance from your cassette
player and tapes:
Clean the tape head and other parts regular-
ly.
A dirty tape head or tape path can de-
crease sound quality and tangle your cas-
sette tapes. The easiest way to clean them
is by using a cleaning tape. (A wet type is
recommended.)
Use high−quality cassettes:
Low−quality cassette tapes can cause
many problems, including poor sound, in-
consistent playing speed, and constant
auto−reversing. They can also get stuck or
tangled in the cassette player.
Do not use a cassette if it has been dam-
aged or tangled or if its label is peeling off.
Do not leave a cassette in the player if
you are not listening to it, especially if it is hot
outside.
Store cassettes in their cases and out of
direct sunlight.
Avoid using cassettes with a total playing
time longer than 100 minutes (50 minutes
per side). The tape used in these cassettes
is thin and could get stuck or tangled in the
cassette player.Caring for your multidisc player and
discs
Your multi−disc player is intended for use
with 12 cm (4.7 in.) discs only.
Extremely high temperature can keep
your multi−disc player from working. On hot
days, use air conditioning to cool the vehicle
interior before you listen to a disc.
Bumpy roads or other vibrations may
make your multi−disc player skip.
If moisture gets into your multi−disc play-
er, you may not hear any sound even though
your multi−disc player appears to be work-
ing. Remove the magazine from the player
and wait until it dries.
CAUTION
Multidisc players use an invisible
laser beam which could cause
hazardous radiation exposure if
directed outside the unit. Be sure to
operate the player correctly.

cxcii
20R457
Labeled discs
NOTICE
Do not use special shaped, trans-
parent/translucent, low quality or la-
beled discs such as those shown in
the illustrations. The use of such
discs may damage the player or
changer, or it may be impossible to
eject the disc.
This system is not designed for use
of Dual Disc. Do not use Dual Disc
because it may cause damage to the
player or changer.
EMV8032U
Correct Wrong
Handle discs carefully, especially when
you set them into the magazine. Hold them
on the edge and do not bend them. Avoid
getting fingerprints on them, particularly on
the shiny side.
Dirt, scratches, warping, pin holes, or
other disc damage could cause the player to
skip or to repeat a section of a track. (To see
a pin hole, hold the disc up to the light.)
EMV8033U
To clean a disc: Wipe it with a soft, lint−free
cloth that has been dampened with water.
Wipe in a straight line from the center to the
edge of the disc (not in a circle). Do not use
a conventional record cleaner or anti−static
device.
VI