engine TOYOTA LAND CRUISER 2008 J200 User Guide

36 1−2. Opening, closing and locking the doors
*1: A message will be shown on the multi−information display in the instru−
ment cluster.
*2: If the engine does not start when the electronic key is inside the vehicle,
the electronic key battery may be depleted or there may be difficulties
receiving signal front the key. (
P. 481)
nIf the smart key system does not operate properly
l
Locking and unlocking the doors: Use the mechanical key. ( P. 481)
lStarting the engine: P. 150
n
P. 410
nCustomization that can be configured at Toyota dealer
Settings (e.g. smart key system) can be changed. (Customizable features
P. 519)
AlarmSituation Correction procedure
Interior alarm
pings once and
exterior alarm
sounds 3 times
*1
The driver ’s door was
closed after the key was
carried outside the vehicle,
and the “ENGINE START
STOP” switch was not
turned OFFTurn the “ENGINE
START STOP” switch
OFF and close the
driver ’s door again
An occupant carried the
electronic key outside the
vehicle and closed the
door while the “ENGINE
START STOP” switch was
not OFF
Bring the electronic
key back into the vehi−
cle

41
1−2. Opening, closing and locking the doors
1
Before driving
n2step unlocking function
When you press the button, the driver ’s door is unlocked. Pressing
the button again within 3 seconds unlocks the other doors.
nOperation signals
Doors: A buzzer sounds and the emergency flashers flash to indicate that
the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice)
Windows and moon roof: A buzzer s
ounds when the windows and moon roof
begin to open.
n
P. 3 0
n
P. 3 3
nAlarm
Using the wireless remote control to lock the door will set the alarm system.
(P. 97)
n
P. 481
nIf the wireless remote control does not operate properly
l
Locking and unlocking the doors: Use the mechanical key. ( P. 481)
lStarting the engine: ( P. 149)
n
P. 410
n
P. 3 0
nCustomization that can be configured at Toyota dealer
Settings (e.g. 2−step unlocking function) can be changed. (Customizable
features
P. 519)

44 1−2. Opening, closing and locking the doors
Locking the driver ’s doors from the outside without a key
Move the inside lock button to the lock position.
Close the door.
The door cannot be locked if the “ENGINE START STOP” switch is in
ACCESSORY or IGNITION ON mode, or the electronic key is left
inside the vehicle.
The key may not be detected correctly and the door may be locked.
Rear door childprotector lock
The door cannot be opened from
inside the vehicle when the locks
are set.
These locks can be set to prevent
children from opening the rear
doors. Press down rear door
switches to lock the rear doors.
STEP1
STEP 2
ITY12C032

45
1−2. Opening, closing and locking the doors
1
Before driving
Automatic door locking and unlocking systems
The following functions can be set or canceled:
nSetting and canceling the functions
To switch between setting and canceling, follow the procedure
below:
Close all the doors and switch the “ENGINE START STOP”
switch IGNITION ON mode. (Perform step 2 within 20 sec−
onds.)
Shift the shift lever to “P” or “N”,
press and hold the driver ’s door
lock switch (
or) for 5 sec−
onds then release.
The shift lever and switch posi−
tions corresponding to the
desired function to be set or can−
celed are shown as follows.
Function Operation
Shift position linked
door locking functionShifting the shift lever out of “P” locks all
doors.
Shift position linked
door unlocking functionShifting the shift lever to “P” unlocks all
doors.
Speed linked door lock−
ing functionAll doors are locked when the vehicle speed is
approximately 12 mph (20 km/h) or higher.
Driver ’s door linked door
unlocking function
All doors are unlocked when the driver ’s door
is opened within 10 seconds after turning the
“ENGINE START STOP” switch OFF.
STEP1
STEP 2

63
1−3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
Linking driving position memory with door unlock operation
Record your driving position to button “1”, “2” or “3” before performing
the following:
Using the wireless remote control
Turn the “ENGINE START STOP” switch to OFF and close
the driver ’s door.
While pressing the desired but−
ton (“1”, “2” or “3”), press
on the wireless remote control
until the signal beeps.
The driving position is recalled
when the driver ’s door is
unlocked using the entry function
or wireless remote control and the
driver ’s door is opened.
STEP1
1SET23
ITY13C130
STEP2
nCanceling the linked door unlock operation
Turn the “ENGINE START STOP” switch to OFF and close the
driver ’s door.
Using the wireless remote control: While pressing “SET” button,
press button on the wireless remote control until the signal
beeps.
STEP1
STEP 2

64 1−3. Adjustable components (seats, mirrors, steering wheel)
nRetained accessory power
Each memorized position (except for the steering wheel position) can be
activated within 30 seconds after the driver ’s door is opened, even if the
“ENGINE START STOP” switch turns off.
nTo cancel seat position recall
Perform any one of the following operations.
lPress the “SET” button
lPress button “1”, “2” or “3”.
lAdjust the seat using the switches (only cancels seat position recall)
nIf the battery is disconnected
The memorized positions must be reset because the computer ’s memory is
erased when the battery is disconnected.
CAUTION
nSeat adjustment caution
Take care during seat adjustment that the seat does not strike the rear pas−
senger or squeeze your body against the steering wheel.

77
1
1−3. Adjustable components (seats, mirrors, steering wheel)
Before driving
Steering wheel
Auto tilt away and auto return
When the “ENGINE START
STOP” switch is OFF, the steer−
ing wheel returns to its stowed
position by moving up and away
to enable easier driver entry and
exit.
Switching to ACCESSORY or
IGNITION ON mode will return
the steering wheel to the original
position. The steering wheel can be adjusted to a comfor table position while
the “ENGINE START STOP” switch is in ACCESSORY or IGNITION
ON mode.
Up
Down
Toward the driver
Away from the driver4
1
2
3
ITY13C064
ITY13C066

79
1
1−3. Adjustable components (seats, mirrors, steering wheel)
Before driving
Inside rear view mir ror
nTo prevent sensor error
CAUTION
nWhile driving
Do not adjust the position of the mirror.
Doing so may lead to mishandling of the vehicle and an accident, or result−
ing in death or serious injury.
In auto mode, sensors are used to detect the headlights of vehicles
behind and automatically
reduces the reflected light.
Turns auto mode on/off
The indicator comes on when
auto mode is turned on.
The mirror will revert to the
auto mode each time the
“ENGINE START STOP”
switch is turned to IGNITION
ON mode.
To ensure correct functioning of the sen−
sors, do not touch or cover the sensors.
ITY13C080

80
1−3. Adjustable components (seats, mirrors, steering wheel)
Outside rear view mir rors
Folding back the mirrors
Press the switch
Pressing again will extended the
mirror. Mirror angle can be adjusted usin g the switch when the “ENGINE
START STOP” switch is in ACCESSORY or IGNITION ON mode.
Select a mirror to adjust
Left
Right
Adjust the mirror
Up
Right
Down
Left
STEP1
STEP 2
ITY13C074

84 1−4. Opening and closing the windows and moon roof
nThe power windows can be operated when
The “ENGINE START STOP” switch is in IGNITION ON mode.
nLinked door lock window operation
lThe power windows can be opened and closed using the mechanical
key. ( P. 43)
lThe power windows can be opened using the wireless remote control.
(P. 40)
lThe power windows can be closed using the smart key system.
nOperating the power windows after turning the “ENGINE START STOP”
switch OFF
The power windows can be operated for approximately 45 seconds even
after the “ENGINE START STOP” switch is turned ACCESSORY mode or
turned OFF. They cannot, however, be operated once the driver ’s or front
passenger ’s door is opened.
nJam protection function
If an object becomes caught between the window and the window frame,
window travel is stopped and the window is opened slightly.
nCustomization that can be configured at Toyota dealer
Settings (e.g. linked door lock operation) can be changed. (Customizable
features P. 519)