ignition TOYOTA MATRIX 2012 E140 / 2.G Quick Reference Guide

2
OVERVIEW
Instrument panel
Steering wheel audio controls
Telephone controls*
Voice command button*
Ignition switch
Cruise control*
VSC/TRAC OFF switch
Auxiliary storage
Power outside rearview mirror control
Headlight, turn signal and front fog light*controls
Wiper and washer controls
“AIR BAG ON” and “AIR BAG OFF” indicator
Front passenger seat belt reminder lightE
E
A
A
O
P
A
P
T
T
H
*
Steering wheel controls
125432_resize Matrix-QRG.qxd 11/23/11 9:32 PM Page 2

8
FEATURES/OPERATIONS
Automatic Transmission (if equipped)
* The ignition switch must be “ON” and the brake pedal depressed to shi\
ft from Park.
Shift the shift lever to “S” position from “D” position.
+: Upshift (push and release)
-: Downshift (pull and release)
Downshifting increases power going uphill, or provides engine braking downhill.
For best fuel economy during normal driving conditions, always drive with t\
he shift
lever in the “D” position.
“S” (Sequential) mode
3
2L
Standard typeMulti-mode type
Park*
Reverse
Neutral
Drive
“S” mode
Park*
Reverse
Neutral
Drive
Third gear
Second gear
First gear
3
2
L
“S”“D”
Automatic door locks can be programmed to operate in three different modes, or
turned OFF.
-Doors lock when shifting from Park.
-Doors unlock when shifting into Park.
-Doors unlock when the driver’s door is opened within 10 seconds after setting the ignition switch to “ACC” or “LOCK” position.
Refer to the Owner’s Manual for more details.
Se
Se
S
H
S
Se
Fron
Auto lock/unlock (if equipped)
125432_resize Matrix-QRG.qxd 11/23/11 9:32 PM Page 8

OVERVIEW
FEATURES/OPERATIONS
SAFETY AND EMERGENCYFEATURES
19
Power outlet-12V DC (if equipped)
Power outlet-115V AC (if equipped)
Designed for 12V car accessories.
The ignition switch must be in the “ACC” or “ON” position.
The ignition switch must be in the “ON” position.
om
he
4
in
Bottle holders
Front Rear
ne
125432_resize Matrix-QRG.qxd 11/23/11 9:32 PM Page 19

20
Moving the lever to “LOCK” will allow the door to be opened only from th\
e
outside.
Rear door
Doors-Child safety locks
System reset initialization
1. Push and hold “SET” button
until the indicator blinks
three times.
2. Wait a few minutes to allow initialization to complete.
Push up, or squeeze
lock release to lower
Seat belts-Shoulder belt anchor
SAFETY AND EMERGENCY FEATURES
If be
beyo
child
To fi
syste
Se
Sp
To o
Rem
(1) T
(2) L
Refe
(1)
Tire Pressure Monitoring (warning)
System
After adjusting tire pressures, or after tires have been rotated or replaced,\
turn
the ignition switch to “ON” and press and hold the “ SET” button until indicator
blinks three times. Let the vehicle sit for a few minutes to allow initializat\
ion to
complete.
Refer to the load label on the door jamb or the Owner’s Manualfor tire inflation
specifications.
If the tire pressure indicator flashes for more than 60 seconds and then r\
emains
on, take the vehicle to your local Toyota dealer.
NOTE : The warning light may come on due to temperature changes or changes in
tire pressure from natural air leakage. If the system has not been initializ\
ed
recently, setting the tire pressures to factory specifications should turn off th\
e
light.
125432_resize Matrix-QRG.qxd 11/23/11 9:32 PM Page 20