Remove door cylinder lock TOYOTA PRIUS 2001 Service Repair Manual

Start
Insert a master key into the key cylinder.
Repeatedly turn the key from ignition switch LOCK to ON 5 times.
Remove the master key. Repeat driver's door open/close operation 6 times.
End
Insert the key to be registered into the key cylinder.
Turn the key from ignition switch LOCK to ON and stay for 60 secs. or more.
Remove the key from the key cylinder.
Open and close a driver's door.
No Ye sWithin 15 secs.
Register next key?
Within 20 secs.
Within 10 secs.
Within 10 secs.
Within 10 secs.
*5*4 *3 *1
*2
± BODY ELECTRICALHYBRID VEHICLE IMMOBILISER SYSTEM
BE±107
1774 Author: Date:
2001 PRIUS (RM778U)
7. REGISTERING MASTER KEY
Initial condition: All doors closed, not key in cylinder.
*1: The 1 st door's open/close operation should be within 15 sec after key insertion.
*2: Remove the key within 20 sec. after the 1 st door's open/close operation.
*3: Insert the key within 10 sec. after preceding key removal.
*4: Turn the key from ignition switch LOCK to ON within 10 sec. after key insertion.
*5: If registering the other key, insert it into the key cylinder within 10 sec.

Start
Insert a master key into the key cylinder.
Repeatedly turn the key from ignition switch LOCK to ON 4 times.
Remove the master key. Repeat door's open/close operation 5 times.
End
Insert the key to be registered into the key cylinder.
Turn the key from ignition switch LOCK to ON and stay for 60 secs. or more.
Remove the key from the key cylinder.
Register next key?
Open and close a door once.
No Ye s
Within 10 secs.
*5
Within 15 secs.
Within 20 secs.
Within 10 secs.
Within 10 secs.
*4 *3 *1
*2
BE±108
± BODY ELECTRICALHYBRID VEHICLE IMMOBILISER SYSTEM
1775 Author: Date:
2001 PRIUS (RM778U)
8. REGISTERING SUB±KEY
Initial condition: All doors closed, not key in cylinder.
*1: The 1 st door's open/close operation should be within 15 sec after key insertion.
*2: Remove the key within 20 sec. after the 1 st door's open/close operation.
*3: Insert the key within 10 sec. after preceding key removal.
*4: Turn the key from ignition switch LOCK to ON within 10 sec. after key insertion.
*5: If registering the other key, insert it into the key cylinder within 10 sec.

Start
Insert a master key into the key cylinder.
Repeatedly turn the key from ignition switch LOCK to ON 6 times.
Remove the master key. Repeat driver's door open/close operation 7 times.
End
*1: The 1 st door's open/close operation should be done within 15 sec after key insertion.
*2: Remove the key within 20 sec. after the 1 st door's open/close operation.
*1
*2
Within 15 secs.
Within 20 secs.
± BODY ELECTRICALHYBRID VEHICLE IMMOBILISER SYSTEM
BE±109
1776 Author: Date:
2001 PRIUS (RM778U)
9. ERASURE OF TRANSPONDER KEY CODE
(a) Do this operation to erase transponder key registration from the transponder key ECU.
HINT:
Delete all other master and sub±key codes leaving the master key code to use the operation. When using
the key which was used before deletion, it is necessary to register the code again.
(b) Initial condition: All doors closed, not key in cylinder.

H15435
H15436
BO±14
± BODYFRONT DOOR
2001 PRIUS (RM778U)
14. REMOVE WINDOW REGULATOR
(a) Disconnect the connector.
(b) Remove the 2 bolts from the window regulator.
Torque: 4.9 N´m (50 kgf´cm, 43 in.´lbf)
(c) Remove the 4 bolts and window regulator.
Torque: 8.3 N´m (85 kgf´cm, 74 in.´lbf)
HINT:
At the time of reassembly, please refer to the following item.
Apply MP grease to the window regulator.
NOTICE:
At the time of reassembly, please refer to the following
item.
Do not apply grease to the spring of the window regulator.
15. REMOVE DOOR LOCK
(a) Disconnect the control cable from the clamp.
(b) Disconnect the 2 links from the outside handle and key
cylinder.
(c) Disconnect the connecter.
(d) Remove the bolt.
Torque: 4.9 N´m (50 kgf´cm, 43 in.´lbf)
(e) Remove the 3 screws and door lock.
Torque: 4.9 N´m (50 kgf´cm, 43 in.´lbf)
HINT:
At the time of reassembly, please refer to the following item.

Apply adhesive to the 3 screws.
Part No. 08833±00070, THREE BOND 1324 or equiva-
lent

H10815
± BODYFRONT DOOR
BO±15
2001 PRIUS (RM778U)

Apply MP grease to the sliding and rotating parts of the
door lock.
16. REMOVE OUTSIDE HANDLE
(a) Remove the 2 bolts and outside handle.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Remove the key cylinder from the handle.

H15434
BO±22
± BODYREAR DOOR
2001 PRIUS (RM778U)
HINT:
At the time of reassembly, please refer to the following item.
Apply MP grease to the sliding and rotating parts of the door
lock.
19. REMOVE OUTSIDE HANDLE
(a) Remove the 2 bolts.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Remove the outside handle and key cylinder.

BO3QS±01
H15480
H15418
H15419
H15420
BO±26
± BODYLUGGAGE COMPARTMENT DOOR AND HINGE
2001 PRIUS (RM778U)
REMOVAL
1. REMOVE LUGGAGE COMPARTMENT DOOR TRIM
Remove the 10 clips and luggage compartment door trim.
2. REMOVE LUGGAGE COMPARTMENT DOOR LOCK
(a) Remove the 2 bolts and luggage compartment door lock.
Torque: 5.4 N´m (55 kgf´cm, 48 in.´lbf)
(b) Disconnect the link and cable from the lock.
3. REMOVE LUGGAGE COMPARTMENT DOOR OUTER
GARNISH
(a) Remove the 4 nuts.
(b) Remove the luggage compartment door outer garnish
and key cylinder.
4. REMOVE LICENCE PLATE LIGHT
(a) Disconnect the connector.
(b) Remove the licence plate light as shown in the illustration.
(c) Employ the same manner described above to the other
side.
(d) Using a clip remover, remove the clamps.
5. REMOVE LUGGAGE COMPARTMENT DOOR
Remove the 4 bolts luggage compartment door.
Torque: 8.3 N´m (85 kgf´cm, 74 in.´lbf)
6. REMOVE LUGGAGE REAR FLOOR FINISH PLATE
(a) Using a clip remover, remove the 4 clips.
(b) Remove the rear floor finish plate.
7. REMOVE LUGGAGE COMPARTMENT DOOR WEATH-
ERSTRIP