replacement TOYOTA RAV4 1996 Service User Guide

REAR DOOR OUTER PANEL (ASSY)
REMOVAL
Positioning Tape
Braze
Braze
Installation
Position
Hemming Location
Disc Sander
2. After grinding off the hemming location, remove
the outer panel. 1. Before removing the outer panel, make the
installation position with a tape.
BODY PANEL REPLACEMENTREœ6

mm in.
10 0.39
INSTALLATION
Positioning Tape
Braze
Braze
Body sealer
about 10mm
Do not close the
drain hole.
Body Sealer
Cloth Tape
30°
Hemming Tool
1. Before temporarily installing the new parts,
apply body sealer to the side impact protecœ
tion beam and back side of the new parts.
HINT:
1) Apply sealer evenly about l0 mm (0.39in.)
from the flange and 3mm (0.12in.) in diameter
to the outer panel and apply just enough sealœ
er for the side impact protection beam to
make contact.
2) For other sealing points, refer to section AR.
2. Bend the flange hem about 30° with a hamœ
mer and dolly, then fasten tightly with a hemœ
ming tool.
HINT:
1) Perform hemming in three steps, being careful
not to warp the panel.
2) If a hemming tool cannot be used, hem with a
hammer and dolly.
BODY PANEL REPLACEMENTREœ7

ROCKER OUTER PANEL (CUT)
REMOVAL
[Cut and Join Location]
Cut and Join Location
(Cut Location for Supply Parts)
Cut and Join Location
(Cut Location for Supply Parts)
Cut and Join Location
(Cut Location for Supply Parts)
[Cut and Join Location]
[Cut and Join Location]
1. Cut and join the new parts at the location shown
above.
HINT: Take care not to damage the internal reinforceœ
ment of the center body pillar.
BODY PANEL REPLACEMENTREœ8

INSTALLATION
Butt Weld
Butt Weld
Butt Weld
1. Temporarily install the new parts and check the
fit of the front door and rear door.
BODY PANEL REPLACEMENTREœ9

mm in.
150
2505.91
9.84
QUARTER PANEL (CUT)
REMOVAL
[Cut and Join Location]
250 mm
Cut and Join Location
Cut and Join Location
[Cut Location for
supply parts]
RH:
LH:
Cut and Join Location
150 mm
[Cut and Join Location]
Braze
RH:
LH:
1. Cut and join the parts at the location shown
above.
BODY PANEL REPLACEMENTREœ10

mm in.
5
0.20
INSTALLATION
Butt Weld
Body Sealer
Butt Weld
RH:
LH:
Butt weld
Body sealer
Braze
about 5 mm
RH:
LH:
2. Temporarily install the new parts and check
the fit of the rear door, back door and rear
combination light. 1. Before temporarily installing the new parts,
apply body sealer to the wheel arch.
HINT:
1) Apply body sealer about 5 mm (0.20in.) from
the flange, avoiding any oozing.
2) Apply sealer evenly, about 3 - 4 mm (0.12 -
0.16in.) in diameter.
3) For other sealing points, refer to section AR.
BODY PANEL REPLACEMENTREœ11

QUARTER PANEL (CUT-P)
REMOVAL
Cut and Join Location
RH:
LH:
Braze
RH:
LH:
1. Cut and join the parts at the location shown
above.
BODY PANEL REPLACEMENTREœ12

mmin.
5
0.20Braze
INSTALLATION
Butt Weld
Body Sealer
RH:
LH:
Body Sealer
about 5 mm
RH:
LH:
1. Before temporarily installing the new parts,
apply body sealer to the wheel arch.
HINT:
1) Apply body sealer about 5 mm (0.20 in.) from
the flange, avoiding any oozing.
2) Apply sealer evenly, about 3 - 4 mm (0.12 -
0.16 in.) diameter.
3) For other sealing points, refer to section AR.
2. Temporarily install the new parts and check the
fit of the rear door, back door and rear combinaœ
tion light.
3. Before welding, cut the lining away from the
weld seams a little.
BODY PANEL REPLACEMENTREœ13

QUARTER WHEEL HOUSING OUTER PANEL
(ASSY): Right Side
REMOVAL (With the quarter panel removed.)
BODY PANEL REPLACEMENTREœ14

INSTALLATION
Assembly Mark
Assembly Mark
Quarter Wheel Housing
Bracket
2. Before welding the new parts, temporarily
install the quarter panel and check the fit. 1. Determine the position of the new parts by the
assembly marks of the inner and outer panels.
BODY PANEL REPLACEMENTREœ15