TOYOTA RAV4 1996 Service Repair Manual

S01626
Disconnect
P15391
S01284
SST
S01629
SSTSST
− ENGINE MECHANICALTIMING BELT
EM−25
1996 RAV4 (RM447U)
Remove the backing paper from a new gasket and
install the gasket evenly to the part of the timing belt
cover shaded black in the illustration.
After installing the gasket, press down on it so that
the adhesive firmly sticks to the timing belt cover.
(b) Disconnect the engine wire protector between the cylin-
der head cover and No. 3 timing belt cover.
(c) Install the No. 2 timing belt cover with the 4 bolts.
(d) Install the engine wire to the No. 2 timing belt cover.
(e) Install the engine wire protector to the 2 mounting bolts of
the No. 2 timing belt cover in the sequence shown.
15. REMOVE CRANKSHAFT PULLEY
16. INSTALL RH ENGINE MOUNTING BRACKET
Using SST, install the mounting bracket with the 3 bolts.
SST 09249−63010
Torque:
52 N·m (530 kgf·cm, 38 ft·lbf)
35 N·m (360 kgf·cm, 26 ft·lbf) for SST
HINT:
Use a torque wrench with a fulcrum length of 340 mm (13.39 in)
17. INSTALL CRANKSHAFT PULLEY
(a) Align the pulley set key with the key groove of the pulley,
and slide on the pulley.
(b) Using SST (and bolt), install the pulley bolt.
SST 09213−54015 (91651−60855 for type A),
09330−00021
Bolt: Part No. 91121−40665 for type B
Torque: 108 N·m (1,100 kgf·cm, 80 ft·lbf)
18. INSTALL SPARK PLUGS

S01352
Ground Strap EM−26
− ENGINE MECHANICALTIMING BELT
1996 RAV4 (RM447U)
19. INSTALL RH ENGINE MOUNTING INSULATOR
(a) Attach the mounting insulator to the body and mounting
bracket with the 4 bolts and 2 nuts.
(b) Tighten the 3 bolts holding the mounting insulator to the
body.
Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)
(c) Tighten the 2 nuts and bolt holding the mounting insulator
to the mounting bracket.
Torque:
37 N·m (380 kgf·cm, 27 ft·lbf) for bolt
52 N·m (530 kgf·cm, 38 ft·lbf) for nut
20. INSTALL AND ADJUST PS PUMP DRIVE BELT
21. INSTALL RH ENGINE UNDER COVER
22. INSTALL RH FRONT WHEEL
23. w/ ABS:
INSTALL NO. 3 ABS ACTUATOR BRACKET (See page
BR−41)
24. INSTALL GENERATOR BRACKET
(a) Install the bracket with the 3 bolts.
Torque: 42 N·m (425 kgf·cm, 31 ft·lbf)
(b) Connect the ground strap connector.
25. INSTALL GENERATOR (See page CH−19)
26. INSTALL WIRE HARNESS BRACKET FOR DLC1
27. INSTALL PS RESERVOIR BRACKET AND RES-
ERVOIR

EM0EP−03
− ENGINE MECHANICALCYLINDER HEAD
EM−27
1996 RAV4 (RM447U)
CYLINDER HEAD
COMPONENTS

EM−28
− ENGINE MECHANICALCYLINDER HEAD
1996 RAV4 (RM447U)

Z17352
ECM ConnectorConnector on Bracket
Engine Wire
Connector for Relay
Block No. 4
Cowl Side Trim Floor Carpet
Center Cover
Scuff Plate
− ENGINE MECHANICALCYLINDER HEAD
EM−29
1996 RAV4 (RM447U)

EM−30
− ENGINE MECHANICALCYLINDER HEAD
1996 RAV4 (RM447U)

S01821
A16074 See page EM−55
− ENGINE MECHANICALCYLINDER HEAD
EM−31
1996 RAV4 (RM447U)

EM−32
− ENGINE MECHANICALCYLINDER HEAD
1996 RAV4 (RM447U)

EM1B8−02
S01285
S01557
− ENGINE MECHANICALCYLINDER HEAD
EM−33
1996 RAV4 (RM447U)
REMOVAL
1. REMOVE RH ENGINE UNDER COVER
2. DRAIN ENGINE COOLANT
3. A/T only:
DISCONNECT THROTTLE CABLE FROM THROTTLE
BODY
4. DISCONNECT ACCELERATOR CABLE FROM
THROTTLE BODY
5. REMOVE AIR CLEANER CAP AND CASE
6. REMOVE GENERATOR (See page CH−7)
7. REMOVE DISTRIBUTOR
8. REMOVE FRONT EXHAUST PIPE
(a) Using a 14 mm deep socket wrench, remove the 3 nuts
holding the front exhaust pipe to the front TWC.
(b) Remove the 2 bolts holding the front exhaust pipe to the
TWC w/ pipe.
(c) Remove the front exhaust pipe and 2 gaskets.
9. REMOVE EXHAUST MANIFOLD AND HEAT INSULA-
TOR ASSEMBLY
(a) Disconnect the oxygen sensor (bank 1 sensor 1) connec-
tor.
(b) Disconnect the oxygen sensor (bank 1 sensor 2) connec-
tor.
(c) Remove the 6 bolts and manifold upper heat insulator.
(d) Remove the 2 bolts holding the RH exhaust manifold stay
to the cylinder block.
(e) Remove the 6 nuts, the exhaust manifold and heat insula-
tor assembly.

S01823
Oxygen Sensor
(Bank 1 Sensor 1)
Oxygen Sensor (Bank 1 Sensor 2)
P03152
S01368
S01365
S01594
EM−34
− ENGINE MECHANICALCYLINDER HEAD
1996 RAV4 (RM447U)
10. REMOVE OXYGEN SENSOR (BANK 1 SENSOR 1)
FROM EXHAUST MANIFOLD
11. REMOVE OXYGEN SENSOR (BANK 1 SENSOR 2)
FROM FRONT TWC
12. SEPARATE EXHAUST MANIFORD AND FRON TWC
(a) Remove the 5 bolts and lower manifold heat insulator.
(b) Remove the 8 bolts and 2 TWC heat insulators.
(c) Remove the 3 bolts, 2 nuts, TWC, gasket retainer and
cushion.
13. DISCONNECT OIL PRESSURE SWITCH CONNECTOR
14. REMOVE WATER OUTLET
(a) Disconnect the ECT sensor connector.
(b) Disconnect the ECT sender gauge connector.
(c) Disconnect the radiator hose from the water outlet.
(d) Disconnect the water bypass pipe hose from the water
outlet.
(e) Disconnect the heater water hose from the water outlet.
(f) Remove the 2 nuts, water outlet and gasket.
15. REMOVE WATER BYPASS PIPE
(a) Remove the bolt, 2 nuts and oil cooler heat protector.
(b) Disconnect the IAC valve water bypass hose from the wa-
ter bypass pipe.
(c) Disconnect the heater water hose from the water bypass
pipe.
(d) Disconnect the 2 oil cooler water bypass hoses from the
oil cooler.
(e) Remove the nut and disconnect the wire protector.
(f) Remove the 2 bolts and 2 nuts.
(g) Disconnect the water bypass pipe from the water pump
cover, and remove the water bypass pipe.
(h) Remove the gasket and O−ring.
16. REMOVE THROTTLE BODY (See page SF−30)