display TOYOTA RAV4 1996 Service Repair Manual

DI3Z5−01
Vehicle Brought to Workshop
Customer Problem Analysis P. DI−2
Problem Symptom Confirmation
If the engine does not start perform steps 10 and 12 firstConnect the OBD II scan tool or TOYOTA hand−held tester to DLC3 P. DI−3
If the display indicates a communication fault in the tool, inspect DLC3 P. DI−3
Check DTC and Freeze Frame Data (Pre−check)
Record or Print DTC and Freeze Frame Data P. DI−3
Clear DTC and Freeze Frame Data P. DI−3
Visual Inspection
Setting the Check Mode Diagnosis P. DI−3
Symptom Simulation P.IN−20
Basic Inspection P. DI−3DTC Chart P. DI−14
Matrix Chart of Problems Symptoms P. DI−20
Circuit Inspection P. DI−21
Adjustment, Repair
DTC Check P. DI−3
Titles insideare titles of pages in
in the bottom portion. See the indicated
pages for detailes explanations.this manual, with the page number indicated
Malfunction
occurs.Malfunction does not occur.
Parts Inspection
Check for Intermittent Problems P. DI−3
Identification of Problem
Confirmation Test
End 1
2
3
4
5
6
7
108
9
11
12
13
15 14
16
Normal Malfunction code.
17
− DIAGNOSTICSENGINE
DI−1
1996 RAV4 (RM447U)
ENGINE
HOW TO PROCEED WITH TROUBLESHOOTING
Troubleshoot in accordance with the procedure on the following pages.

S02459
− DIAGNOSTICSENGINE
DI−5
1996 RAV4 (RM447U) Terminal No.
Connection / Voltage or ResistanceCondition
2Bus  Line / Pulse generationDuring transmission
4Chassis Ground / ↔ Body Ground 1 Ω or lessAlways
5Signal Ground / ↔ Body Ground 1 Ω or lessAlways
16Battery Positive / ↔ Body Ground 9 ∼ 14VAlways
HINT:
If your display shows ”UNABLE TO CONNECT TO VEHICLE”
when you have connected the cable of the OBDII scan tool or
TOYOTA hand−held tester to DLC3, turned the ignition switch
ON and operated the scan tool, there is a problem on the ve-
hicle side or tool side.
If communication is normal when the tool is connected to
another vehicle, inspect DLC3 on the original vehicle.
If communication is still not possible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool’s instruction manual.
2. INSPECT DIAGNOSIS (Normal Mode)
(a) Check the MIL.
(1) The MIL comes on when the ignition switch is turned
ON and the engine is not running.
HINT:
If the MIL does not light up, troubleshoot the combination meter.
(2) When the engine is started, the MIL should go off.
If the lamp remains on,the diagnosis system has
detected a malfunction or abnormality in the sys-
tem.
(b) Check the DTC.
NOTICE:
TOYOTA hand−held tester only:
When the diagnosis system is switched from normal mode
to check mode, it erases all DTC and freezed frame data re-
corded in normal mode. So before switching modes, al-
ways check the DTC and freezed frame data, and note them
down.
(1) Prepare the OBDII scan tool (complying with SAE
J1978) or TOYOTA hand−held tester.
(2) Connect the OBDII scan tool or TOYOTA hand−
held tester to DLC3 at the lower of the instrument
panel.
(3) Turn the ignition switch ON and turn the OBDII scan
tool or TOYOTA hand−held tester switch ON.
(4) Use the OBDII scan tool or TOYOTA hand−held tes-
ter to check the DTC and freezed frame data, note
them down.
(5) See page DI−14 to confirm the details of the
DTC.

DI−12
− DIAGNOSTICSENGINE
1996 RAV4 (RM447U)
7. ENGINE OPERATING CONDITION
NOTICE:
The value given below for ”Normal Condition” are representative values, so a vehicle may still be
normal even it its value varies from those listed here. So do not decide whether a part is faulty or not
solely according to the ”Normal Condition” here.
(a) CARB Mandated Signals
TOYOTA hand−held tester displayMeasurement ItemNormal Condition *
FUEL SYS #1
Fuel System Bank 1
OPEN: Air−fuel ratio feedback stopped
CLOSED: Air−fuel ratio feedback operating
Idling after warning up: CLOSED
CALC LOAD
Calculator Load:
Current intake air volume as a proportion of max.
intake air volumeIdling: 20.7 − 48.4 %
Racing without load (2,500 rpm) : 17.7 − 45.3 %
COOLANT TEMPEngine Coolant Temperature Sensor ValueAfter warning up: 80 − 95°C (176 − 203°F)
SHORT FT #1Short−term Fuel Trim Bank 10 ± 20 %
LONG FT #1Long−term Fuel Trim Bank 10 ± 20 %
ENGINE SPDEngine SpeedIdling: 700 ± 50 rpm
VEHICLE SPDVehicle SpeedVehicle Stopped: 0 km/h (0 mph)
IGN ADVANCEIgnition Advance
Ignition Timing of Cylinder No.1Idling: BTDC 0 − 10°
INTAKE AIRIntake Air Temperature Sensor ValueEquivalent to Ambient Temp.
MAPAbsolute Pressure Inside Intake ManifoldIdling: 21 − 49 kPa
Racing without load (2,500 rpm): 17 − 46 kPa
THROTTLE POS
Voltage Output of Throttle Position Sensor
Calculated as a Percentage
0V → 0 %, 5V → 100 %Throttle Fully Closed: 6 − 16 %
Throttle Fully Open: 64 − 98 %
O2S B1, S1Voltage Output of Oxygen Sensor
Bnak 1,Sensor 1Idling : 0.1 − 0.9 V
O2FT B1, S1Oxygen Sensor Fuel Trim Bank 1, Sensor 1
(Same as SHORT FT #1)0 ± 20 %
O2S B1, S2Voltage Output of Oxygen Sensor
Bank 1, Sensor 2Driving 50 km/h (31 mph): 0.1 − 0.9 V
*: If no conditions are specifically stated for ”Idling”, it means the shift lever is at N or P position, the A/C switch
is OFF and all accessory switches are OFF.

− DIAGNOSTICSENGINE
DI−13
1996 RAV4 (RM447U)
(b) TOYOTA Enhanced Signals
TOYOTA hand−held tester displayMeasurement ItemNormal Condition *
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 RPM
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 9 g/r
INJECTORFuel injection time for cylinder No.1Idling: 1.9 − 3.3 ms
IAC DUTY RATIOIntake Air Control Valve Duty Ratio Opening
ratio rotary solenoid type IAC valveIdling: 25 − 60 %
STARTER SIGStarter SignalCranking: ON
A/C SIGA/C Switch SignalA/C ON: ON
PNP SWPark / Neutral Position Switch SignalP or N position: ON
ELCTRCL LOAD SIGElectrical Load SignalDefogger S/W ON: ON
STOP LIGHT SWStop Light Switch SignalStop light switch ON: ON
FC IDLFuel Cut Idle: Fuel cut when throttle valve fully
closed, during decelerationFuel cut operating: ON
FC TAUFuel Cut TAU: Fuel cut during very light loadFuel cut operating: ON
CYL#1
CYL#2
CYL#3
CYL#4
Abnormal revolution variation for each cylinder0 %
IGNITIONTotal number of ignitions for every 1,000
revolutions0 − 2,000
EGR SYSTEMEGR system operating conditionIdling: OFF
FUEL PUMPFuel Pump SignalIdling: ON
EVAP (PURGE) VSVEVAP VSV SignalVSV operating: ON
VAPOR PRESS VSVVapor Pressure VSV SignalVSV operating: ON
A/C CUT SIGA/C Cut SignalA/C S/W OFF: ON
TOTAL FT B1Total Fuel Trim Bank 1: Average value for fuel
trim system of bank 1Idling: 0.8 − 1.2
O2 LR B1, S1
Oxygen Sensor Lean Rich Bank 1, Sensor 1
Response time for oxygen sensor output to
switch from lean to rich.
Idling after warned up: 0 − 1,000 msec.
O2 RL B1, S1
Oxygen Sensor Rich Lean Bank 1, Sensor 1
Response time for oxygen sensor output to
switch from rich to lean.
Idling after warned up: 0 − 1,000 msec.
*: If conditions are specifically stated for ”Idling” , it means the shift lever is at N or P Position, the A/C switch
is OFF and all accessory switches are OFF.

DI3Z8−02
DI−14
− DIAGNOSTICSENGINE
1996 RAV4 (RM447U)
DIAGNOSTIC TROUBLE CODE CHART
HINT:
Parameters listed in the chart may not be exactly the same as your reading due to the type of instrument
or other factors.
If a malfunction code is displayed during the DTC check in check mode, check the circuit for that code listed
in the table below, for details of each code, turn to the page referred to under the ”See page” for the respec-
tive ”DTC No.” in the DTC chart.
SAE DEFINED
DTC No.
(See Page)Detection ItemTrouble AreaMILMemory
P0105
(DI−21)
Manifold Absolute
Pressure / Barometric
Pressure Circuit
MalfunctionOpen or short in Manifold absolute pressure sensor circuit
Manifold absolute pressure sensor
ECM
 *1
P0106
(DI−24)
Manifold Absolute
Pressure / Barometric
Pressure Circuit
Ranger / Performance
Problem
Manifold absolute pressure sensor *1
P0110
(DI−25)Intake Air Temp. Circuit
MalfunctionOpen or short in take air temp. sensor circuit
Intake air temp. sensor
ECM
 *1
P0115
(DI−29)Engine Coolant Temp. Circuit
MalfunctionOpen or short in engine coolant temp. sensor circuit
Engine coolant temp. sensor
ECM
 *1
P0116
(DI−33)Engine Coolant Temp. Circuit
Range / Performance ProblemEngine coolant temp. sensor
Cooling system *1
P0120
(DI−34)Throttle / Pedal Position
Sensor / Switch ”A” Circuit
MalfunctionOpen or short in throttle position sensor circuit
Throttle position sensor
ECM
 *1
P0121
(DI−38)Throttle / Pedal Position
Sensor / Switch ”A” Circuit
Range / Performance Problem
Throttle position sensor *1
P0125
(DI−39)Insufficient Coolant Temp. for
Closed Loop Fuel ControlOpen or short in oxygen sensor circuit
Oxygen sensor *1
P0130
(DI−42)Oxygen Sensor Circuit Malfunc-
tion
(Bank 1 Sensor 1)Oxygen sensor
Fuel trim malfunction *1
P0133
(DI−45)Oxygen Sensor Circuit Slow
Response
(Bank 1 Sensor 1)
Oxygen sensor *1
P0136
(DI−46)Oxygen Sensor Circuit
Malfunction
(Bank 1 Sensor 2)
Oxygen sensor *1
P0171
(DI−48)System too Lean
(Fuel Trim)
Air Intake (hose loose)
Fuel line pressure
Injector blockage
Oxygen sensor malfunction
Manifold absolute pressure sensor
Engine coolant temp. sensor
 *1
*1: MIL lights up

FI4741
20 30
10
5
3
2
0.1 0.2 0.3 0.51
−20
(−4) 0
(32) 20
(68) 40
(104) 60
(140) 80
(176)100
(212)
Temperature °C (°F) Acceptable
Resistance (Ω)
(fig. 1)
− DIAGNOSTICSENGINE
DI−25
1996 RAV4 (RM447U)
DTC P0110 Intake Air Temp. Circuit Malfunction
CIRCUIT DESCRIPTION
The intake air temp. sensor is built into the air cleaner cap and
senses the intake air temperature.
A thermistor built in the sensor changes the resistance value
according to the intake air temperature.
The lower the intake air temperature, the greater the thermistor
resistance value, and the higher the intake air temperature, the
lower the thermistor resistance value (See Fig. 1.).
The intake air temperature sensor is connected to the ECM
(See next page). The 5 V power source voltage in the ECM is
applied to the intake air temperature sensor from the terminal
THA via a resistor R.
That is , the resistor R and the intake air temperature sensor are
connected in series. When the resistance value of the intake air
temperature sensor changes in accordance with changes in the
intake air temperature, the potential at terminal THA also
changes. Based on this signal, the ECM increases the fuel in-
jection volume to improve driveability during cold engine opera-
tion.
If the ECM detects the DTC ”P0110”, it operates the fail safe
function in which the intake air temperature is assumed to be
20°C (68°F).
Intake Air Temp.
°C (°F)Resistance
(kΩ)Voltage
(V)
−20 (−4)16.24.3
0 (32)5.93.4
20 (68)2.52.4
40 (104)1.11.4
60 (140)0.60.9
80 (176)0.30.5
100 (212)0.20.3
DTC No.DTC Detecting ConditionTrouble Area
P0110Open or short in intake air temp. sensor circuit
Open or short in intake air temp. sensor circuit
Intake air temp. sensor
ECM
HINT:
After confirming DTC P0110 use the OBDII scan tool or TOYOTA hand−held tester to confirm the intake air
temperature from ”CURRENT DATA”.
Temperature DisplayedMalfunction
− 40°C (− 40°F)Open circuit
140°C (284°F) or moreShort circuit
DI3ZE−01

P19746
Engine Coolant Temp. Sensor
W
BRE5
E5E2THW5V
E1 94ECM
2
1
− DIAGNOSTICSENGINE
DI−29
1996 RAV4 (RM447U)
DTC P0115 Engine Coolant Temp. Circuit Malfunction
CIRCUIT DESCRIPTION
A thermistor built into the engine coolant temperature sensor changes the resistance value according to the
engine coolant temperature.
The structure of the sensor and connection to the ECM is the same as in the intake air temp. circuit malfunc-
tion shown on page DI−25.
If the ECM detects the DTC P0115, it operates the fail safe function in which the engine coolant temp. is
assumed to be 80°C (176°F).
DTC No.DTC Detecting ConditionTrouble Area
P0115Open or short in engine coolant temp. sensor circuit
Open or short in engine coolant temp. sensor circuit
Engine coolant temp. sensor
ECM
HINT:
After confirming DTC P0115 use the OBDII scan tool or TOYOTA hand−held tester to confirm the engine
coolant temperature from ”CURRENT DATA”.
Temperature DisplayedMalfunction
− 40°C (− 40°F)Open circuit
140°C (284°F) or moreShort circuit
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
If DTC ”P0105” (Manifold Absolute Pressure / Barometric Pressure Circuit Malfunction), ”P0110” (Intake Air
Temp. Circuit Malfunction), ”P0115” (Engine Coolant Temp. Circuit Malfunction), ”P0120” (Throttle / Pedal
Position Sensor / Switch ”A” Circuit Malfunction) are output simultaneously, E2 (sensor ground) may be
open.
DI3ZF−01

(7)
(5) (4)(6)
(3)
(2)
(1)
P20769
Vehicle Speed
70 − 90 km/h
(43 − 56 mph)
Idling
IG SW OFF
Warm up
3 − 5 mins2 mins 3 − 5 mins 2 mins Time
DI−66
− DIAGNOSTICSENGINE
1996 RAV4 (RM447U)
SYSTEM CHECK DRIVING PATTERN
(1) Connect the OBDII scan tool or TOYOTA hand−held tester to the DLC3.
(2) Start and warm it up the engine with all accessories switched OFF.
(3) Run the vehicle at 70 − 90 km/h (43 − 56 mph) for 3 minutes or more.
(4) Idle the engine for about 2 minutes.
(5) Stop at safe place and turn the ignition switch OFF.
(6) Start the engine and do steps (3) and (4) again.
(7) Check the ”READINESS TESTS” mode on the OBDII scan tool or TOYOTA hand−held tester. If ”COMPL”
is displayed and the MIL does not light up, the system is normal. If ”INCMPL” is displayed and the MIL does
not light up, run the vehicle again and check it.
HINT:
”INCMPL” is displayed when either condition (a) or (b) exists.
The system check is incomplete.
There is malfunction in the system.
If there is a malfunction in the system, the MIL will light up after step (2) to (6) above are done.
INSPECTION PROCEDURE
HINT:
If DTC ”P0150” and / or ”P0106” and ”P0401” are output simultaneously, perform troubleshooting or
DTC ”P0105” first.
If DTC ”P0401” and ”P0402” are output simultaneously, perform troubleshooting of DTC ”P0402” first.

A04252
C9V−W
E6ECM
SPD5 V
2
9 Combination Meter
− DIAGNOSTICSENGINE
DI−95
1996 RAV4 (RM447U)
WIRING DIAGRAM
INSPECTION PROCEDURE
1 Check operation of speedometer.
CHECK:
Drive the vehicle and check it the operation of the speedometer in the combination meter is normal.
HINT:
The vehicle speed sensor is operating normally if the speedometer display is normal.
NG Check speedometer circuit. See combination
meter troubleshooting.
OK

DI409−02
Vehicle Brought to Workshop
P.DI−126
Connect the OBD ll Scan Tool or TOYOTA Hand−Held Tester to DLC3
If your display shows ”UNABLE TO CONNECT TO VEHICLE” when you have
connected the scan tool/TOYOTA hand−held tester, inspect DLC3 P. DI−127
Check DTC and Freeze Frame Data (Pre−check)
Record or Print DTC and Freeze Frame Data P. DI−127
Clear DTC and Freeze Frame Data P. DI−127 Customer Problem Analysis
Visual Inspection
DTC CheckSymptom Simulation Setting the Check Mode Diagnosis P. DI−127
Problem Symptom Confirmation
P. IN−20 Symptom does
not occur
OK Codethe page number indicated in the bottom portion. See the
indicated pages for detailed explanations.
Preliminary Checkare titles of pages in the manual, with Item inside
Mechanical System Tests DTC Chart
Chapter 1
(Electronic)Manual Shifting Test
Matrix Chart of Symptoms Problems − P. DI−140
(On−vehicle)
 Pattern Select Signal Check  O/D Signal Check
InspectionCircuit(Off−vehicle) Chapter 2 Chapter 3
END Repair
Confirmation Test
Identification of ProblemParts Inspection P. DI−127
P. DI−127P. DI−127
P. DI−127
P. DI−127
P. DI−145 − DI−168 P. DI−141 1
2
P. DI−141P. DI−141 3
4
5
6
78
9
1011
12
13
14
16
18 15
17
Symptom occurs
OKNG
OKNG
NG
OK
OK OK
NG
NGNG
Step 2, 3, 4, 6, 9, 15, 18:
Diagnostic steps permitting the use of the TOYOTA
hand−held tester or TOYOTA brake−out−box.
− DIAGNOSTICSAUTOMATIC TRANSAXLE (A241E)
DI−125
1996 RAV4 (RM447U)
AUTOMATIC TRANSAXLE (A241E)
HOW TO PROCEED WITH TROUBLESHOOTING
Trobleshoot in accordance with the procedure on the follwoing pages.